Sigurd Wenner
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Sigurd Wenner has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Randi Holmestad
Norwegian University of Science and Technology (NTNU)
14 shared publications Calin D. Marioara
Materials and Chemistry, SINTEF, NO-7491 Trondheim, Norway
7 shared publications- Sigmund Jarle Andersen
SINTEF Materials and Chemistry, Trondheim, Norway
5 shared publications - Calin Daniel Marioara
SINTEF Industry, Trondheim, Norway
4 shared publications Dai Tomono
RIKEN Nishina Center for Accelerator Based Science, RIKEN
4 shared publicationsKatsuhiko Nishimura
University of Toyama
4 shared publications
Latest Publications
- Open Access
- 17 August 2024
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 141 (43)
Inception of vented water trees in high voltage XLPE cable insulation: Effect of inorganic contaminations inside the semiconductive material
Wet‐design AC subsea power cables are currently rated up to a maximum voltage of 72.5 kV. These high voltage (HV) cables are cost‐effective alternatives to subsea cables kept dry by a protective lead sheath and exhibit superior properties for dynamic applications. However, several vented water trees, degradation phenomena reducing the cable lifetime, are observed in a HV XLPE insulated cable subjected to wet aging in the laboratory. The water trees initiate from a smooth and clean XLPE insulation/semiconductive screen interface. In this paper, we show that voids in the range 15–150 μm are observed in the conductor screen, 50–320 μm from the water tree inception sites. Degradation of the semiconductive material is observed, in the form of porous regions that connect the voids to the water tree inception sites. NaCl impurities are detected on the void surfaces and in the porous regions. These features are proposed to be the pre‐requisites for the formation of the vented water trees observed in this type of cable. The mechanism responsible for the formation of the void and porous regions in the semiconductive cable screen is discussed based on the observations.
- 17 August 2024
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 141 (43)
Open AccessInception of vented water trees in high voltage XLPE cable insulation: Effect of inorganic contaminations inside the semiconductive material
Wet‐design AC subsea power cables are currently rated up to a maximum voltage of 72.5 kV. These high voltage (HV) cables are cost‐effective alternatives to subsea cables kept dry by a protective lead sheath and exhibit superior properties for dynamic applications. However, several vented water trees, degradation phenomena reducing the cable lifetime, are observed in a HV XLPE insulated cable subjected to wet aging in the laboratory. The water trees initiate from a smooth and clean XLPE insulation/semiconductive screen interface. In this paper, we show that voids in the range 15–150 μm are observed in the conductor screen, 50–320 μm from the water tree inception sites. Degradation of the semiconductive material is observed, in the form of porous regions that connect the voids to the water tree inception sites. NaCl impurities are detected on the void surfaces and in the porous regions. These features are proposed to be the pre‐requisites for the formation of the vented water trees observed in this type of cable. The mechanism responsible for the formation of the void and porous regions in the semiconductive cable screen is discussed based on the observations.
- Open Access
Atomic Layer Deposition of Titanium Oxide-Based Films for Semiconductor Applications—Effects of Precursor and Operating Conditions
Two widely used atomic layer deposition precursors, Tetrakis (dimethylamido) titanium (TDMA-Ti) and titanium tetrachloride (TiCl4), were investigated for use in the deposition of TiOx-based thin films as a passivating contact material for solar cells. This study revealed that both precursors are suited to similar deposition temperatures (150 °C). Post-deposition annealing plays a major role in optimising the titanium oxide (TiOx) film passivation properties, improving minority carrier lifetime (τeff) by more than 200 µs. Aluminium oxide deposited together with titanium oxide (AlOy/TiOx) reduced the sheet resistance by 40% compared with pure TiOx. It was also revealed that the passivation quality of the (AlOy/TiOx) stack depends on the precursor and ratio of AlOy to TiOx deposition cycles.
Open AccessAtomic Layer Deposition of Titanium Oxide-Based Films for Semiconductor Applications—Effects of Precursor and Operating Conditions
Two widely used atomic layer deposition precursors, Tetrakis (dimethylamido) titanium (TDMA-Ti) and titanium tetrachloride (TiCl4), were investigated for use in the deposition of TiOx-based thin films as a passivating contact material for solar cells. This study revealed that both precursors are suited to similar deposition temperatures (150 °C). Post-deposition annealing plays a major role in optimising the titanium oxide (TiOx) film passivation properties, improving minority carrier lifetime (τeff) by more than 200 µs. Aluminium oxide deposited together with titanium oxide (AlOy/TiOx) reduced the sheet resistance by 40% compared with pure TiOx. It was also revealed that the passivation quality of the (AlOy/TiOx) stack depends on the precursor and ratio of AlOy to TiOx deposition cycles.
- 26 October 2018
- Published by Oxford University Press (OUP) in Microscopy
- Vol. 67 (suppl_2) , i17
2aB_SS2-2The Connection Between Inter-Granular Corrosion Resistance and Precipitate Microstructure in an AA6005A Alloy
Due to their optimal combination of mechanical properties and corrosion resistance, the Al-Mg-Si(-Cu) alloys are increasingly being used in the automotive industry and as construction materials. Their properties are given by high numbers of nano-sized metastable precipitates which form in the Al matrix during a heat treatment. Cu additions to Al-Mg-Si alloys increase material strength, but at the expense of inter-granular corrosion resistance [1–3]. Transmission electron microscopy techniques have been used to measure precipitate parameters (types, atomic structures, compositions, numbers, size, volume fractions) as well as elemental segregation at grain boundaries. It is found that Cu incorporation into metastable Mg-Si precipitates can be controlled by manipulation of the thermo-mechanical treatment. Conditions with higher Cu incorporation into precipitates have a reduced segregation of Cu at grain boundaries and showed an increased resistance to inter-granular corrosion.
- 26 October 2018
- Published by Oxford University Press (OUP) in Microscopy
- Vol. 67 (suppl_2) , i17
2aB_SS2-2The Connection Between Inter-Granular Corrosion Resistance and Precipitate Microstructure in an AA6005A Alloy
Due to their optimal combination of mechanical properties and corrosion resistance, the Al-Mg-Si(-Cu) alloys are increasingly being used in the automotive industry and as construction materials. Their properties are given by high numbers of nano-sized metastable precipitates which form in the Al matrix during a heat treatment. Cu additions to Al-Mg-Si alloys increase material strength, but at the expense of inter-granular corrosion resistance [1–3]. Transmission electron microscopy techniques have been used to measure precipitate parameters (types, atomic structures, compositions, numbers, size, volume fractions) as well as elemental segregation at grain boundaries. It is found that Cu incorporation into metastable Mg-Si precipitates can be controlled by manipulation of the thermo-mechanical treatment. Conditions with higher Cu incorporation into precipitates have a reduced segregation of Cu at grain boundaries and showed an increased resistance to inter-granular corrosion.
- 1 November 2016
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 684, 195-200
Precipitation in a mixed Al–Cu–Mg/Al–Zn–Mg alloy system
- 1 November 2016
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 684, 195-200
Precipitation in a mixed Al–Cu–Mg/Al–Zn–Mg alloy system
- 1 June 2016
- Published by Elsevier in Scripta Materialia
- Vol. 118, 5-8
Accurately measured precipitate–matrix misfit in an Al–Mg–Si alloy by electron microscopy
- 1 June 2016
- Published by Elsevier in Scripta Materialia
- Vol. 118, 5-8
Accurately measured precipitate–matrix misfit in an Al–Mg–Si alloy by electron microscopy
- 14 September 2015
- Published by Taylor & Francis in Philosophical Magazine
- Vol. 95 (31) , 3524-3534
Structural modifications and electron beam damage in aluminium alloy precipitate θ'–AL2
The –Al Cu phase in an Al–4Zn–2Cu–1Mg–0.7Si (wt.%) alloy was investigated by means of scanning transmission electron microscopy. With our specific alloy composition, the phase is often formed with stacking faults on and planes. The stacking faults on planes are often regularly spaced and create a previously unreported superstructure. Structural damage by electron irradiation is observed, even at a low acceleration voltage of 80 kV. The damage is more pronounced in the precipitates with stacking faults, which agrees with theoretical calculations of knock-on scattering cross-sections. These two very different forms of disruptions of the structure are linked to its spacious interstitial sites and the ease at which Cu atoms diffuse into and between them.
- 14 September 2015
- Published by Taylor & Francis in Philosophical Magazine
- Vol. 95 (31) , 3524-3534
Structural modifications and electron beam damage in aluminium alloy precipitate θ'–AL2
The –Al Cu phase in an Al–4Zn–2Cu–1Mg–0.7Si (wt.%) alloy was investigated by means of scanning transmission electron microscopy. With our specific alloy composition, the phase is often formed with stacking faults on and planes. The stacking faults on planes are often regularly spaced and create a previously unreported superstructure. Structural damage by electron irradiation is observed, even at a low acceleration voltage of 80 kV. The damage is more pronounced in the precipitates with stacking faults, which agrees with theoretical calculations of knock-on scattering cross-sections. These two very different forms of disruptions of the structure are linked to its spacious interstitial sites and the ease at which Cu atoms diffuse into and between them.
- 1 August 2015
- Published by Elsevier in Materials Characterization
- Vol. 106, 226-231
A hybrid aluminium alloy and its zoo of interacting nano-precipitates
- 1 August 2015
- Published by Elsevier in Materials Characterization
- Vol. 106, 226-231
A hybrid aluminium alloy and its zoo of interacting nano-precipitates
- 26 August 2014
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 45 (12) , 5777-5781
Clustering and Vacancy Behavior in High- and Low-Solute Al-Mg-Si Alloys
- 26 August 2014
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 45 (12) , 5777-5781
Clustering and Vacancy Behavior in High- and Low-Solute Al-Mg-Si Alloys