WJWenlong Jia

Wenlong Jia

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Wenlong Jia has a total of 106 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Numerical Simulation of Sloshing-Induced and Static Thermodynamic Responses in a Liquid Helium Storage Tank

    by Chao Li, Quanfeng Shen, Zhaorong Shi, Wenlong Jia

    Liquid helium storage tanks undergo coupled heat ingress, thermal stratification, self-pressurization, and sloshing, but the empirical phase-change frequency used in conventional Lee models limits their reproducibility. This study couples the volume-of-fluid method, a layer-by-layer multilayer insulation/liquid nitrogen shield heat leak model, and a calibrated temperature-dependent Lee closure. The complete correlation, coefficients, evaporation adjustment factor (χ = 0.1), phase change sources, saturation relation, and latent heat source are reported. The full field after 3 h of static heat ingress is mapped into a 30 s sinusoidal sloshing calculation at 0.6 Hz and 0.3 g. In the liquid helium self-pressurization benchmark, the relative deviation of the average pressurization rate decreases from 39.64% for the best tested fixed-frequency Lee case (1.0 × 10−4 s−1) to 14.32% for the calibrated closure. After 3 h, the vapor pressure reaches 81,332.53 Pa and the average liquid centerline temperature gradient reaches 18.00 × 10−4 K/m. Sloshing produces an interfacial mixing layer approximately 0.43 m thick. The simulated pressure signals exhibit only a small downward drift; because time step sensitivity and global mass/energy balance data are unavailable, no numerically resolved pressure drop magnitude is claimed. The reported sloshing results are limited to the two-dimensional transverse plane model.

  • A Unified Multiscale Quantification Method of Adhesive Strength in Crude Oil Precipitates: Bridging Atomic Force Microscopy and Pull-Off Experiments via Discrete Element Method Modeling

    by Huan Xiao, Wenlong Jia, Min Xiang, Fan Yang, Shuoshuo Song, Xiujuan Wang, Yang Chen, Anvar R. Valeev

    Summary: The objective of this study is to establish a unified multiscale method for quantitatively characterizing the adhesion behavior at the crude oil precipitate-steel interface. Crude oil precipitates exhibiting pronounced viscoelasticity tend to deposit and accumulate on the inner walls of steel pipes and tanks, posing a threat to the safety of crude oil storage and transportation. Effectively inhibiting or removing crude oil precipitates from steel plate walls requires a thorough understanding of the multiscale adhesion characteristics and underlying mechanisms at the precipitate-steel plate interface. However, despite extensive experimental efforts at individual scales, a clear quantitative mapping between microscale adhesion mechanisms and macroscale adhesion stress has not yet been established, limiting the predictive capability of existing approaches. In this study, the microscopic morphology and microadhesion properties of crude oil precipitates were quantitatively characterized using atomic force microscopy (AFM). Simultaneously, the macroscopic adhesion stress at the precipitate-steel plate interface was quantitatively evaluated through macroscopic pull-off (POF) tests. Building upon these experimental insights and the Johnson-Kendall-Roberts (JKR) contact theory, an innovative discrete element method (DEM) model was developed to simulate the separation dynamics at the precipitate-steel plate interface. This model establishes a quantitative and bidirectional mapping between AFM-measured microscale adhesion and macroscale adhesion force by introducing interfacial energy as a physically consistent coupling parameter. This multiscale approach provided a unified quantitative characterization of the adhesion force between the precipitate and steel interface. For three types of crude oil precipitates, the relative errors between the DEM simulation predictions and the AFM and POF experiments were lower than 12.1%. The proposed multiscale adhesion characterization method provides quantitative tools for engineering decision-making in flow assurance. It allows the optimization of mechanical cleaning operations, such as determining the critical jet velocity in hydrodynamic cleaning and the required cavitation intensity in ultrasonic cleaning. It also offers a high-throughput criterion for evaluating chemical inhibitors and antifouling coatings based on their ability to reduce interfacial energy and adhesion stress.

  • Characteristic Analysis of a One-Dimensional Single-Pressure Three-Fluid Model for the Stratified Flow Pattern in a Pipe

    by C. J. Li, Y. P. Liao, W. L. Jia, F. Yang, J. He, Q. J. Huang

    Three-phase flow is commonly present in oil and gas production pipelines. Three-fluid models are extensively used for numerical simulation. Accurately modeling and solving the three-phase flow model is fundamental for monitoring the flow parameters and ensuring production stability. However, the model may be ill-posed under certain initial conditions. No reliable methods have long been used to judge the well-posedness of three-fluid models. This study presents a universal method for determining the well-posedness of the three-fluid model, which can judge the model’s well-posedness of single-phase, two-phase, and three-phase flow under the stratified flow pattern. The model’s well-posedness range in the subsonic region becomes notably limited under the high pressure and the large fluid density ratios. A convenient eigenvalue map method with a wide range of liquid holdup and pressure to analyze the three-fluid model’s hyperbolicity is proposed, which can intuitively describe the well-posed range of the model under typical operating conditions and the distribution of model eigenvalue signs, as well as determine the boundary parameters on the pipelines' inlet and outlet boundaries. The three-fluid model has the largest well-posed range under low pressure and low liquid holdup. The proposed method provides a reference for well-posed analysis and accurate solution of the three-fluid model.


  • Open Access

    Safety-Oriented Coordinated Operation Algorithms for Natural Gas Pipeline Networks and Gas-Fired Power Generation Facilities

    by Xinyi Wang, Feng Wang, Qin Bie, Wenlong Jia, Yong Jiang, Ying Liu, Yuanyuan Tian, Yuxin Zheng, Jie Sun

    The natural gas pipeline network transmission system involved in the coordinated operation of pipeline networks and gas-fired power generation facilities is complex. It consists of multiple components, such as gas sources, users, valves, compressor stations, and pipelines. The addition of natural gas-fired power generation facilities overlaps with the high and low peak periods of civil gas, imposing dual peak-shaving pressures on pipeline networks and requiring more stringent operational control strategies for maintaining system stability. To address the aforementioned issues and improve the overall operating revenues of the system, we proposed the coordinated optimization model of gas-fired power generation facilities, pipeline networks, gas storage, and compressor stations. The optimization algorithm is written using the penalty function method of the Interior Point OPTimizer (IPOPT) solver. Meanwhile, the basic parameters of the system’s pipeline networks, users, gas storage, natural gas-fired power generation facilities, compressors, and electricity prices were input into the solver. The research results reveal that the algorithm ensures solution accuracy while accounting for computational efficiency and practical applicability. The algorithm can be used to effectively calculate the ideal coordinated operation solution, significantly improve the operating revenues of the system, and achieve safe, stable, coordinated, and efficient operation of the system.


  • Experimental and Numerical Simulation of Heavy Precipitate Removal from the Walls of Crude Oil Tanks Using the Ultrasonic Cleaning Method

    by Wenlong Jia, Huan Xiao, Xiangyu Leng, Qiaojing Huang, Changjun Li

    Summary: The ultrasonic method is a potentially efficient and green method for cleaning precipitates on the wall of crude oil tanks using high-speed cavitation microjets. Nevertheless, current studies have ignored the connection between the macroscopic ultrasonic cleaning rate (UCR) and mesoscopic cavitation bubble collapse microjet dynamics. The effect and mechanism of ultrasonic cavitation microjet cleaning (UCJC) of crude oil precipitates are unclear. In this study, we experimentally prove the feasibility of UCJC of crude oil precipitates and quantitatively analyze the influence of ultrasonic parameters on the macroscopic UCR. The Maxwell equation is used to modify the precipitate constitutive equation considering the precipitate viscoelasticity, and a numerical computational model is developed for the UCJC of precipitates based on Ansys® Fluent software. To illustrate the mechanism and law of UCJC of precipitates at the macroscopic level, the effects of ultrasonic operating parameters on the microjet velocity, diameter, and cavitation pit size are analyzed at the mesoscopic level through experimental and numerical simulation methods. The results show that the ultrasonic operating parameters determine the mesoscale cavitation pit size and macroscopic UCR by controlling the microjet diameter and velocity. Specifically, the microjet velocity increases from 53.2 m/s to 116.1 m/s, and the average diameter of the cavitation crater is increased from 6.28 μm to 17.48 μm when the ultrasonic pressure is increased from 120 kPa to 485 kPa, resulting in an increase in the UCR from 533.3 mg/(h·m2) to 2256.3 mg/(h·m2). Nevertheless, the microjet velocity and diameter decrease by 36.42% and 63.14%, respectively, when the ultrasonic frequency is increased from 20 kHz to 100 kHz, resulting in a decrease in the UCR from 845.3 mg/(h·m2) to 594.7 mg/(h·m2).


  • Open Access

    RETRACTED: Zhang et al. Strength Analysis and Reinforcement of 120 m3 Liquid Helium Storage Tank for Transportation Case. Processes 2025, 13, 100

    by Jianguo Zhang, Chao Li, Fa’an Liu, Jing Xu, Qinghua Liu, Shuhui Ma, Changjun Li, Wenlong Jia, Longjiang Li

    The journal retracts and removes the article titled “Strength Analysis and Reinforcement of 120 m3 Liquid Helium Storage Tank for Transportation Case”

  • Open Access

    RETRACTED: Strength Analysis and Reinforcement of 120 m3 Liquid Helium Storage Tank for Transportation Case

    by Jianguo Zhang, Chao Li, Fa’an Liu, Jing Xu, Qinghua Liu, Shuhui Ma, Changjun Li, Wenlong Jia, Longjiang Li


  • Open Access

    Numerical Study on Heat Leakage, Thermal Stratification, and Self-Pressurization Characteristics in Liquid Helium Storage Tanks

    by Jing Xu, Fa’an Liu, Jianguo Zhang, Chao Li, Qinghua Liu, Changjun Li, Wenlong Jia, Shixiong Fu, Longjiang Li

    During the operation of liquid-phase He-4 (LHe-4) storage tanks, heat leakage changes the thermophysical parameters and phase properties of the LHe-4 in the tanks, resulting in the thermal layering phenomenon. This phenomenon is characterized by the LHe-4 temperature gradient and pressure increase (self-pressurization) phenomena in the tanks. Based on the Layer-by-Layer model, a heat transfer model of a composite adiabatic structure with multilayer insulation and liquid nitrogen screen (LNCS) insulation was established, and the Neumann boundary heat flux of the thermal response model was determined. A numerical simulation model of the thermal response of a liquid helium storage tank was established. The spatial and temporal evolutions of the pressure distribution, natural convection characteristics, thermal stratification characteristics, and self-pressurization characteristics of the LHe-4 tank were investigated. Finally, the self-pressurization thermodynamic model of the LHe-4 storage tank was built based on the isothermal saturation and homogeneous model. It is shown that the predictive performance of the mLee model for the self-boosting characteristics (relative deviation of 14.32%) was significantly improved compared with that of the Lee model (relative deviation of 39.64%). The thermal stratification degree (TSD) of the tank increased with the operation time, with TSDs of 1.023, 1.028, and 1.036 at 1 h, 2 h, and 3 h, which exacerbated the self-pressurization of the tank. The wall surface in contact with the phase interface is a strong evaporation point, so the interfacial mass transfer rate maps show a pattern of high at both ends and low in the middle.


  • Open Access

    A Predictive Model for Hydrate Formation Conditions in Alcohol-Containing Systems Based on the Cubic-Plus-Association State Equation

    by Yubin Wang, Ziyuan Li, Shujie Zhi, Qi Yang, Changjun Li, Wenlong Jia

    In alcohol-containing systems, the association of polar molecules significantly influences the calculation of water activity, leading to substantial deviations from ideal solution behavior. This makes it challenging for traditional hydrate formation condition models to accurately predict hydrate formation temperatures and pressures. To address this issue, we propose a novel unified thermodynamic framework based on the Parrish-Prausnitz (P-P) model and the Cubic-Plus-Association (CPA) equation of state (EoS) for calculating the hydrate formation condition in systems containing gas/water/alcohol, by using the advantages of the CPA EoS to characterize the association interaction of polar molecules. In addition, we utilize experimental data to model the molecular association in alcohol-containing systems and conduct regression analysis for binary interaction coefficients among alcohol, water, and gas. Multiple sets of experimental data on component fractions and hydrate formation conditions for methane-alcohol-water systems are used for validation. The proposed model shows an average relative error of 1.17–6.42% for predicting alcohol/methane component fractions in the liquid phase and 1.93–4.78% for predicting hydrate formation conditions in alcohol-containing systems. Compared to traditional models, this model demonstrates a significant improvement in accuracy and performs well in predicting hydrate formation conditions in alcohol-containing systems.