Changhai Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Changhai Liu has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Donghui Xia
School of Electrical and Electronic Engineering, Huazhong University of Science and Technology 2 , Wuhan 430074
5 shared publications Fangtai Cui
State Key Laboratory of Advanced Electromagnetic Engineering and Technology, School of Electrical and Electronic Engineering, Huazhong University of Science and Technology, Wuhan 430074, China
2 shared publicationsYikun Jin
State Key Laboratory of Advanced Electromagnetic Engineering and Technology, School of Electrical and Electronic Engineering, Huazhong University of Science and Technology, Wuhan 430074, China
2 shared publicationsZhenxiong Yu
State Key Laboratory of Advanced Electromagnetic Engineering and Technology, School of Electrical and Electronic Engineering, Huazhong University of Science and Technology, Wuhan 430074, China
2 shared publicationsZhijiang Wang
International Joint Research Laboratory of Magnetic Confinement Fusion and Plasma Physics, State Key Laboratory of Advanced Electromagnetic Engineering and Technology, School of Electrical and Electronic Engineering, Huazhong University of Science and Technology, Wuhan, China
2 shared publications- Zhijiang Wang
Huazhong University of Science and Technology
2 shared publications
Latest Publications
- 5 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 48 (6) , 1560-1565
Design of a Launcher for the 105-GHz ECRH System on J-TEXT
- 5 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 48 (6) , 1560-1565
Design of a Launcher for the 105-GHz ECRH System on J-TEXT
- 2 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 66 (11) , 6043-6048
Study of Polarization Strategy for High-Power Millimeter Wave With Two Identical Reflective Gratings
For high-power millimeter systems, reflective gratings (RGs) are usually used to control the wave polarization. This paper presents the polarization strategy with two identical RGs. We use the coordinate transformation method for the RG design. A code based on this method is checked by numerical examples and also low-power experiments. Experiments are carried out at frequencies of 60, 70, and 105 GHz. Four gratings are manufactured for test. We present and compare calculated results of the coordinate transformation method with the numerical results of the integral method and low-power test results. The comparison results indicate that the calculation results of the code are accurate and reliable. Finally, the polarization strategy with two identical RGs is studied with the code. Parameters and polarization characteristics including the bandwidth of designed gratings are given.
- 2 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 66 (11) , 6043-6048
Study of Polarization Strategy for High-Power Millimeter Wave With Two Identical Reflective Gratings
For high-power millimeter systems, reflective gratings (RGs) are usually used to control the wave polarization. This paper presents the polarization strategy with two identical RGs. We use the coordinate transformation method for the RG design. A code based on this method is checked by numerical examples and also low-power experiments. Experiments are carried out at frequencies of 60, 70, and 105 GHz. Four gratings are manufactured for test. We present and compare calculated results of the coordinate transformation method with the numerical results of the integral method and low-power test results. The comparison results indicate that the calculation results of the code are accurate and reliable. Finally, the polarization strategy with two identical RGs is studied with the code. Parameters and polarization characteristics including the bandwidth of designed gratings are given.
- 13 February 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 46 (5) , 1628-1632
Polarizer Designed for the Electron Cyclotron Resonance Heating System on J-TEXT
An electron cyclotron (EC) resonance heating (ECRH) system with four 60-GHz/200-kW/0.5-s gyrotrons donated by the Culham Science Center is being developed on J-TEXT for plasma heating and magnetohydrodynamics studies. A controlled polarization launcher has been designed to inject the EC beam into plasma with the desired polarization and direction. The polarizer with sinusoidal grooves has been integrated into the launcher for polarization control of the EC wave. We use the coordinate transformation method for the polarizer design. The polarization parameters of the designed polarizer, including the rotation angle and the ellipticity, are measured with a low-power test platform. The experimental results agree well with the numerical calculations, indicating that the designed polarizer can meet the requirements of the ECRH system on J-TEXT.
- 13 February 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 46 (5) , 1628-1632
Polarizer Designed for the Electron Cyclotron Resonance Heating System on J-TEXT
An electron cyclotron (EC) resonance heating (ECRH) system with four 60-GHz/200-kW/0.5-s gyrotrons donated by the Culham Science Center is being developed on J-TEXT for plasma heating and magnetohydrodynamics studies. A controlled polarization launcher has been designed to inject the EC beam into plasma with the desired polarization and direction. The polarizer with sinusoidal grooves has been integrated into the launcher for polarization control of the EC wave. We use the coordinate transformation method for the polarizer design. The polarization parameters of the designed polarizer, including the rotation angle and the ellipticity, are measured with a low-power test platform. The experimental results agree well with the numerical calculations, indicating that the designed polarizer can meet the requirements of the ECRH system on J-TEXT.
- 23 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 46 (5) , 1344-1349
Signal Transmission Links for the Electron Cyclotron Resonance Heating System on J-TEXT
Electron cyclotron resonance heating (ECRH) is an important auxiliary heating method which is widely used in magnetic confinement fusion. For the ECRH system on J-TEXT, signals should be transmitted to the control system for monitoring and protection and also to the data acquisition system. Considering the high-voltage and harsh electromagnetic interference environment, reliable fiber-optic transmission links are applied. Transmitted by fiber-optic modules, the response time of digital signals can be less than 1 μs. According to the ECRH system requirements, two practical analog fiber-optic transmission links based on the voltage-to-frequency and frequency-to-voltage conversion technology have been designed and developed. With IC AD650, the delay time of most analog signals is less than 100 μs, and with IC VFC110, critical signal transmission delay can be shortened to 5 μs. The test results indicate that the designed signal transmission links for ECRH system on J-TEXT are stable and reliable.
- 23 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 46 (5) , 1344-1349
Signal Transmission Links for the Electron Cyclotron Resonance Heating System on J-TEXT
Electron cyclotron resonance heating (ECRH) is an important auxiliary heating method which is widely used in magnetic confinement fusion. For the ECRH system on J-TEXT, signals should be transmitted to the control system for monitoring and protection and also to the data acquisition system. Considering the high-voltage and harsh electromagnetic interference environment, reliable fiber-optic transmission links are applied. Transmitted by fiber-optic modules, the response time of digital signals can be less than 1 μs. According to the ECRH system requirements, two practical analog fiber-optic transmission links based on the voltage-to-frequency and frequency-to-voltage conversion technology have been designed and developed. With IC AD650, the delay time of most analog signals is less than 100 μs, and with IC VFC110, critical signal transmission delay can be shortened to 5 μs. The test results indicate that the designed signal transmission links for ECRH system on J-TEXT are stable and reliable.
- 28 November 2017
- Published by IOP Publishing in Plasma Science and Technology
- Vol. 20 (1) , 014018
The anode power supply for the ECRH system on the J-TEXT tokamak
- 28 November 2017
- Published by IOP Publishing in Plasma Science and Technology
- Vol. 20 (1) , 014018
The anode power supply for the ECRH system on the J-TEXT tokamak
- 1 May 2015
- Published by Elsevier in Optics Communications
- Vol. 342, 73-78
Sequential deconvolution from wave-front sensing using bivariate simplex splines
- 1 May 2015
- Published by Elsevier in Optics Communications
- Vol. 342, 73-78
Sequential deconvolution from wave-front sensing using bivariate simplex splines
- 4 November 2009
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7508, 750809-750809-5
Simulation of the computer-generated holographic modal wave front sensor
We introduce a modal wave front sensing technique of using binary computer generated hologram (BCGH) and a coding approach. Several types of Zernike aberrations were encoded into the BCGH using this method. Light wave front was modulated by BCGH and single Zernike aberration mode respectively, and the holographic modal wavefront sensor was simulated and verified. The results show that, wave front distorted by a special aberration mode, after modulated by the BCGH, can be transformed into beams which have a relative intensity, which can reflect the change trend of the aberration coefficients in the unknown wavefront.
- 4 November 2009
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7508, 750809-750809-5
Simulation of the computer-generated holographic modal wave front sensor
We introduce a modal wave front sensing technique of using binary computer generated hologram (BCGH) and a coding approach. Several types of Zernike aberrations were encoded into the BCGH using this method. Light wave front was modulated by BCGH and single Zernike aberration mode respectively, and the holographic modal wavefront sensor was simulated and verified. The results show that, wave front distorted by a special aberration mode, after modulated by the BCGH, can be transformed into beams which have a relative intensity, which can reflect the change trend of the aberration coefficients in the unknown wavefront.