Hasiaoqier Han
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hasiaoqier Han has a total of 59 co-authors. Here are the top co-authors by number of shared publications:
- Zhenbang Xu
Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, No. 3888, Dong Nanhu Road, Changchun 130033, China
8 shared publications Qingwen Wu
5 shared publications- Qingwen Wu
Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033, China
5 shared publications - Jiaxin Li
Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, No. 3888, Dong Nanhu Road, Changchun 130033, China
4 shared publications Zhenbang Xu
4 shared publicationsJunwei Lin
3 shared publications
Latest Publications
- Open Access
Design and Modelling of a Two-Axis Compliant Joint Based on Flexure Leaf Springs
In the field of parallel robots, traditional rigid joints compromise motion accuracy owing to inherent friction and backlash, thus driving the demand for high-performance compliant joints. This paper proposes a parametric design method for a two-axis compliant joint that employs flexure leaf springs (FLSs) as rigid joint alternatives. The joint configuration consists of four FLSs arranged in a revolute–revolute (RR) layout. Based on Euler–Bernoulli beam theory and the deformation superposition principle, linear analytical models for the compliance and stress characteristics of both the flexure leaf spring (FLS) and the compliant joint are derived. These models are validated through finite element analysis (FEA) and rotational motion experiments. The results indicate that the relative errors between the analytical model (AM) and finite element model (FEM) are below 8%, while the relative errors between the AM and experimental data are within 12%. The proposed parametric design method enables rapid preliminary design and the performance evaluation of the two-axis compliant joint, which is intended as a rotational joint for six degrees of freedom (6-DOF) parallel robots with typical applications in high-precision optical alignment.
Open AccessDesign and Modelling of a Two-Axis Compliant Joint Based on Flexure Leaf Springs
In the field of parallel robots, traditional rigid joints compromise motion accuracy owing to inherent friction and backlash, thus driving the demand for high-performance compliant joints. This paper proposes a parametric design method for a two-axis compliant joint that employs flexure leaf springs (FLSs) as rigid joint alternatives. The joint configuration consists of four FLSs arranged in a revolute–revolute (RR) layout. Based on Euler–Bernoulli beam theory and the deformation superposition principle, linear analytical models for the compliance and stress characteristics of both the flexure leaf spring (FLS) and the compliant joint are derived. These models are validated through finite element analysis (FEA) and rotational motion experiments. The results indicate that the relative errors between the analytical model (AM) and finite element model (FEM) are below 8%, while the relative errors between the AM and experimental data are within 12%. The proposed parametric design method enables rapid preliminary design and the performance evaluation of the two-axis compliant joint, which is intended as a rotational joint for six degrees of freedom (6-DOF) parallel robots with typical applications in high-precision optical alignment.
- Open Access
- 3 February 2026
- Published by MDPI AG in Preprints.org
Design and Modeling of a Two-Axis Compliant Joint Based on Flexure Leaf Springs
In the field of parallel robots, traditional rigid joints compromise motion accuracy owing to inherent friction and backlash, thus driving the demand for high-performance com-pliant joints. This paper proposes a parametric design method for a two-axis compliant joint that employs flexure leaf springs (FLSs) as rigid joint alternatives. The joint con-figuration consists of four FLSs arranged in a revolute-revolute (RR) layout. Based on Euler–Bernoulli beam theory and the deformation superposition principle, linear ana-lytical models for the compliance and stress characteristics of both the flexure leaf spring (FLS) and the compliant joint are derived. These models are validated through finite element analysis (FEA) and rotational motion experiments. The results indicate that the relative errors between the analytical model (AM) and finite element model (FEM) are below 8%, while the relative errors between the AM and experimental data are within 12%. The proposed parametric design method enables rapid preliminary design and performance evaluation of compliant joints, which highlights its potential for practical engineering application.
- 3 February 2026
- Published by MDPI AG in Preprints.org
Open AccessDesign and Modeling of a Two-Axis Compliant Joint Based on Flexure Leaf Springs
In the field of parallel robots, traditional rigid joints compromise motion accuracy owing to inherent friction and backlash, thus driving the demand for high-performance com-pliant joints. This paper proposes a parametric design method for a two-axis compliant joint that employs flexure leaf springs (FLSs) as rigid joint alternatives. The joint con-figuration consists of four FLSs arranged in a revolute-revolute (RR) layout. Based on Euler–Bernoulli beam theory and the deformation superposition principle, linear ana-lytical models for the compliance and stress characteristics of both the flexure leaf spring (FLS) and the compliant joint are derived. These models are validated through finite element analysis (FEA) and rotational motion experiments. The results indicate that the relative errors between the analytical model (AM) and finite element model (FEM) are below 8%, while the relative errors between the AM and experimental data are within 12%. The proposed parametric design method enables rapid preliminary design and performance evaluation of compliant joints, which highlights its potential for practical engineering application.
- Open Access
- 29 November 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (23) , 12683
Motion Error of V-Type Roller Linear Guides Considering Geometric Errors of the Guide Rails
V-type roller linear guides can achieve extremely high motion accuracy through precision design and machining; however, theoretical research and methodologies in this field remain limited. This paper proposes a computational method for estimating the motion errors of V-type roller linear guides and establishes a four-degree-of-freedom error model that accounts for guide rail yaw errors, guide rail pitch errors, variations in roller positions, and the contact states of rollers. The effects of the error wavelength ratio, load, and number of roller rows on the motion error of a single V-type roller linear guide are investigated, and the mechanisms and characteristics of the error averaging effect are analyzed. The motion error characteristics of a double V-type roller linear guide are also discussed. Finally, the proposed model is applied to the development and motion error estimation of a double V-type roller linear guide for a grating ruling engine. The straightness of the carriage in the X and Y directions over a 600 mm travel distance reached 0.62 μm and 0.48 μm, respectively. Furthermore, a high-precision echelle diffraction grating with a wavefront PV of 0.21λ was fabricated. These results further validate the proposed model and provide guidance for the manufacturing error allocation and precision design of V-type roller linear guides.
- 29 November 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (23) , 12683
Open AccessMotion Error of V-Type Roller Linear Guides Considering Geometric Errors of the Guide Rails
V-type roller linear guides can achieve extremely high motion accuracy through precision design and machining; however, theoretical research and methodologies in this field remain limited. This paper proposes a computational method for estimating the motion errors of V-type roller linear guides and establishes a four-degree-of-freedom error model that accounts for guide rail yaw errors, guide rail pitch errors, variations in roller positions, and the contact states of rollers. The effects of the error wavelength ratio, load, and number of roller rows on the motion error of a single V-type roller linear guide are investigated, and the mechanisms and characteristics of the error averaging effect are analyzed. The motion error characteristics of a double V-type roller linear guide are also discussed. Finally, the proposed model is applied to the development and motion error estimation of a double V-type roller linear guide for a grating ruling engine. The straightness of the carriage in the X and Y directions over a 600 mm travel distance reached 0.62 μm and 0.48 μm, respectively. Furthermore, a high-precision echelle diffraction grating with a wavefront PV of 0.21λ was fabricated. These results further validate the proposed model and provide guidance for the manufacturing error allocation and precision design of V-type roller linear guides.
- 14 March 2025
- Published by Elsevier in Precision Engineering
- Vol. 94, 330-343
Design and analysis of Leaf-spring flexure hinge with adjustable fillet shapes
- 14 March 2025
- Published by Elsevier in Precision Engineering
- Vol. 94, 330-343
Design and analysis of Leaf-spring flexure hinge with adjustable fillet shapes
- Open Access
Design and Analysis of a Portable Robot for Venous Blood Sampling
Venous blood sampling is a common procedure in medical diagnosis and treatment. However, the stationary manual blood sampling method in current use not only requires human resources but also is inconvenient for elderly persons and patients with limited mobility. To address this issue, this paper proposes a portable robot for venous blood sampling that features a 6-P-RR-R-RR horizontal parallel mechanism in its main structure. This design is better adapted to the shape of the human arm than previous robots, with an offset RR-hinge structure to increase the mechanism’s workspace. The introduction of offset hinge variables makes the kinematic solution more complex than that for conventional parallel mechanisms. This paper uses the kinematic constraint characteristics of the offset hinge to establish a kinematic model of the parallel mechanism, and the Newton–Raphson numerical iterative method is used to perform the computation. The kinematic model and its solutions are verified using kinematics simulation. The robot’s workspace is validated through special pose calculations and simulations to ensure that it meets the required specifications. A test system was built, and the accuracy of the parallel mechanism’s motion was verified.
Open AccessDesign and Analysis of a Portable Robot for Venous Blood Sampling
Venous blood sampling is a common procedure in medical diagnosis and treatment. However, the stationary manual blood sampling method in current use not only requires human resources but also is inconvenient for elderly persons and patients with limited mobility. To address this issue, this paper proposes a portable robot for venous blood sampling that features a 6-P-RR-R-RR horizontal parallel mechanism in its main structure. This design is better adapted to the shape of the human arm than previous robots, with an offset RR-hinge structure to increase the mechanism’s workspace. The introduction of offset hinge variables makes the kinematic solution more complex than that for conventional parallel mechanisms. This paper uses the kinematic constraint characteristics of the offset hinge to establish a kinematic model of the parallel mechanism, and the Newton–Raphson numerical iterative method is used to perform the computation. The kinematic model and its solutions are verified using kinematics simulation. The robot’s workspace is validated through special pose calculations and simulations to ensure that it meets the required specifications. A test system was built, and the accuracy of the parallel mechanism’s motion was verified.
- 19 December 2024
- Published by ASME International in Journal of Mechanisms and Robotics
- Vol. 17 (2) , 1-31
Theoretical Analysis of Workspace of a Hybrid Offset Joint
Offset joints are widely used in robotics, and literature has demonstrated that axial offset joints can expand the workspace. However, the hybrid offset joint, which incorporates offsets in three orthogonal directions (x, y, and z axes), provides a more flexible and comprehensive range of motion compared to traditional axial offset joints. Therefore, a comprehensive understanding of the workspace of hybrid offset joints with three-directional offsets is essential. First, through a parameter model, the interference motion of hybrid offset joints is studied, considering three different directional offsets and obtaining analytical expressions. Next, based on coordinate transformations, the workspace of this joint is investigated, resulting in corresponding theoretical formulas. In addition, the influence of offset amounts in various directions on the joint’s workspace is examined. Finally, the application of hybrid offset joints in parallel manipulators (PMs) is introduced, highlighting their practical engineering value. Through comparative analysis, it is found that lateral offsets on the x- and y-axes adjust the maximum rotation angles, while the z-axis offset expands the rotational range of these joints. Moreover, by increasing the limit rotation angle of the passive joint in a specific direction, the application of hybrid offset joints in PMs can impact the workspace. These findings offer valuable insights for the design of hybrid offset joints and their applications in robotics.
- 19 December 2024
- Published by ASME International in Journal of Mechanisms and Robotics
- Vol. 17 (2) , 1-31
Theoretical Analysis of Workspace of a Hybrid Offset Joint
Offset joints are widely used in robotics, and literature has demonstrated that axial offset joints can expand the workspace. However, the hybrid offset joint, which incorporates offsets in three orthogonal directions (x, y, and z axes), provides a more flexible and comprehensive range of motion compared to traditional axial offset joints. Therefore, a comprehensive understanding of the workspace of hybrid offset joints with three-directional offsets is essential. First, through a parameter model, the interference motion of hybrid offset joints is studied, considering three different directional offsets and obtaining analytical expressions. Next, based on coordinate transformations, the workspace of this joint is investigated, resulting in corresponding theoretical formulas. In addition, the influence of offset amounts in various directions on the joint’s workspace is examined. Finally, the application of hybrid offset joints in parallel manipulators (PMs) is introduced, highlighting their practical engineering value. Through comparative analysis, it is found that lateral offsets on the x- and y-axes adjust the maximum rotation angles, while the z-axis offset expands the rotational range of these joints. Moreover, by increasing the limit rotation angle of the passive joint in a specific direction, the application of hybrid offset joints in PMs can impact the workspace. These findings offer valuable insights for the design of hybrid offset joints and their applications in robotics.
- Open Access
Robot Learning Method for Human-like Arm Skills Based on the Hybrid Primitive Framework
This paper addresses the issue of how to endow robots with motion skills, flexibility, and adaptability similar to human arms. It innovatively proposes a hybrid-primitive-frame-based robot skill learning algorithm and utilizes the policy improvement with a path integral algorithm to optimize the parameters of the hybrid primitive framework, enabling robots to possess skills similar to human arms. Firstly, the end of the robot is dynamically modeled using an admittance control model to give the robot flexibility. Secondly, the dynamic movement primitives are employed to model the robot’s motion trajectory. Additionally, novel stiffness primitives and damping primitives are introduced to model the stiffness and damping parameters in the impedance model. The combination of the dynamic movement primitives, stiffness primitives, and damping primitives is called the hybrid primitive framework. Simulated experiments are designed to validate the effectiveness of the hybrid-primitive-frame-based robot skill learning algorithm, including point-to-point motion under external force disturbance and trajectory tracking under variable stiffness conditions.
Open AccessRobot Learning Method for Human-like Arm Skills Based on the Hybrid Primitive Framework
This paper addresses the issue of how to endow robots with motion skills, flexibility, and adaptability similar to human arms. It innovatively proposes a hybrid-primitive-frame-based robot skill learning algorithm and utilizes the policy improvement with a path integral algorithm to optimize the parameters of the hybrid primitive framework, enabling robots to possess skills similar to human arms. Firstly, the end of the robot is dynamically modeled using an admittance control model to give the robot flexibility. Secondly, the dynamic movement primitives are employed to model the robot’s motion trajectory. Additionally, novel stiffness primitives and damping primitives are introduced to model the stiffness and damping parameters in the impedance model. The combination of the dynamic movement primitives, stiffness primitives, and damping primitives is called the hybrid primitive framework. Simulated experiments are designed to validate the effectiveness of the hybrid-primitive-frame-based robot skill learning algorithm, including point-to-point motion under external force disturbance and trajectory tracking under variable stiffness conditions.
- Open Access
- 29 March 2024
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 112 (11) , 9719-9721
Correction to: Simplified dynamic characteristic analysis method for parallel manipulators with flexure hinges
- 29 March 2024
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 112 (11) , 9719-9721
Open AccessCorrection to: Simplified dynamic characteristic analysis method for parallel manipulators with flexure hinges
- 26 March 2024
- Published by Cambridge University Press (CUP) in Robotica
- Vol. 42 (5) , 1-19
Inverse dynamics analysis of a 6-RR-RP-RR parallel manipulator with offset universal joints
This paper presents an algorithm for solving the inverse dynamics of a parallel manipulator (PM) with offset universal joints (RR–joints) via the Newton–Euler method. The PM with RR–joints increase the joint stiffness and enlarge the workspace but introduces additional joint parameters and constraint torques, rendering the dynamics more complex. Unlike existing studies on PMs with RR–joints, which emphasize the kinematics and joint performance, this paper studies the dynamical model. First, an iterative algorithm is established through a rigid body velocity transformation, which calculates the input parameters of the link velocity and acceleration. A linear system of equations in matrix form is then established for the entire PM through the Newton–Euler method. By using the generalized minimal residual method (GMRES) to solve the equation system, all the forces and torques on the joints can be obtained, from which the required actuation force can be derived. This method is validated through numerical simulations using the automatic dynamic analysis of multibody systems software. The proposed method is suitable for establishing the dynamic model of complex PMs with redundant or hybrid structures.
- 26 March 2024
- Published by Cambridge University Press (CUP) in Robotica
- Vol. 42 (5) , 1-19
Inverse dynamics analysis of a 6-RR-RP-RR parallel manipulator with offset universal joints
This paper presents an algorithm for solving the inverse dynamics of a parallel manipulator (PM) with offset universal joints (RR–joints) via the Newton–Euler method. The PM with RR–joints increase the joint stiffness and enlarge the workspace but introduces additional joint parameters and constraint torques, rendering the dynamics more complex. Unlike existing studies on PMs with RR–joints, which emphasize the kinematics and joint performance, this paper studies the dynamical model. First, an iterative algorithm is established through a rigid body velocity transformation, which calculates the input parameters of the link velocity and acceleration. A linear system of equations in matrix form is then established for the entire PM through the Newton–Euler method. By using the generalized minimal residual method (GMRES) to solve the equation system, all the forces and torques on the joints can be obtained, from which the required actuation force can be derived. This method is validated through numerical simulations using the automatic dynamic analysis of multibody systems software. The proposed method is suitable for establishing the dynamic model of complex PMs with redundant or hybrid structures.