Menno P. de Ridder
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Menno P. de Ridder has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Joost P. Den Bieman
Deltares
5 shared publications Marcel R.A. van Gent
4 shared publicationsDennis C.P. van Kester
3 shared publicationsPatricia Mares-Nasarre
2 shared publications- Anouk de Bakker
Unit of Marine and Coastal Systems, Deltares, 2600 Delft, The Netherlands
1 shared publication - C. W. T. van Bemmelen
Water Resources, Faculty of Civil Engineering and Geosciences Delft University of Technology Delft Netherlands
1 shared publication
Latest Publications
- Open Access
- 20 August 2026
- Published by American Geophysical Union (AGU) in Journal of Geophysical Research: Oceans
- Vol. 131 (8)
Wave Energy Transfer in Shallow Water: Numerical Investigation of Slope and Offshore Wave Condition Effects
This study advances the understanding of nonlinear wave interactions in shallow water by numerically quantifying how foreshore slope and offshore conditions influence energy transfer and wave evolution over a broad range of conditions. Two non‐hydrostatic models, SWASH and XBeach, are validated against physical experiments and applied across a wide range of conditions. The two‐layer SWASH model accurately reproduces wave parameters, third‐order statistics, and nonlinear energy transfer. Results show that the relative water depth , the offshore wave steepness and the Iribarren number are key parameters for describing the interaction strength and biphase behavior. The slope mainly affects high‐frequency biphase behavior, whereas for the other nonlinear interactions it primarily alters the magnitude of the energy transfer. For smaller than 0.2, low‐frequency energy is redistributed toward higher frequencies within the surf zone, while low‐frequencies at steeper slopes only receive energy. In shallow water , energy transfer to higher and lower frequencies is not dominated solely by primary wave interactions. Triads involving two high‐frequency components and one low‐frequency component play a major role, alongside interactions of one low‐frequency component with two primary components. Consequently, milder slopes increase low‐frequency wave height contributions up to 60%, whereas steeper slopes result in 20%–40% for the studied conditions. High‐frequency contributions remain relatively stable across profiles and offshore conditions, accounting for approximately 60%–70% of total wave height in shallow water.
- 20 August 2026
- Published by American Geophysical Union (AGU) in Journal of Geophysical Research: Oceans
- Vol. 131 (8)
Open AccessWave Energy Transfer in Shallow Water: Numerical Investigation of Slope and Offshore Wave Condition Effects
This study advances the understanding of nonlinear wave interactions in shallow water by numerically quantifying how foreshore slope and offshore conditions influence energy transfer and wave evolution over a broad range of conditions. Two non‐hydrostatic models, SWASH and XBeach, are validated against physical experiments and applied across a wide range of conditions. The two‐layer SWASH model accurately reproduces wave parameters, third‐order statistics, and nonlinear energy transfer. Results show that the relative water depth , the offshore wave steepness and the Iribarren number are key parameters for describing the interaction strength and biphase behavior. The slope mainly affects high‐frequency biphase behavior, whereas for the other nonlinear interactions it primarily alters the magnitude of the energy transfer. For smaller than 0.2, low‐frequency energy is redistributed toward higher frequencies within the surf zone, while low‐frequencies at steeper slopes only receive energy. In shallow water , energy transfer to higher and lower frequencies is not dominated solely by primary wave interactions. Triads involving two high‐frequency components and one low‐frequency component play a major role, alongside interactions of one low‐frequency component with two primary components. Consequently, milder slopes increase low‐frequency wave height contributions up to 60%, whereas steeper slopes result in 20%–40% for the studied conditions. High‐frequency contributions remain relatively stable across profiles and offshore conditions, accounting for approximately 60%–70% of total wave height in shallow water.
- Open Access
- 2 May 2026
- Published by Elsevier in Coastal Engineering
- Vol. 209
Wave overtopping discharges at rubble mound structures in shallow water: Effects of directional spreading
- 2 May 2026
- Published by Elsevier in Coastal Engineering
- Vol. 209
Open AccessWave overtopping discharges at rubble mound structures in shallow water: Effects of directional spreading
- Open Access
- 29 May 2025
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 38,p. 54
IMPLEMENTATION AND VALIDATION OF AN INTRA-WAVE SEDIMENT TRANSPORT MODULE IN A DEPTH-AVERAGED NON-HYDROSTATIC WAVE MODEL
XBeach (Roelvink et al., 2009) is an open-source numerical model which simulates hydrodynamic and morphodynamic processes and impacts on coasts on the time scale of storms. The original model approach (Surfbeat mode) explicitly solves wave group and long wave (infragravity) dynamics but parameterizes the intra- wave motions of short (sea-swell) waves. On steep beaches and on coastal structures, this parameterization leads to substantial underestimation of wave run-up (e.g., De Beer et al., 2021) and overtopping (Roelvink et al., 2018). Recently, the model was therefore extended with a non-hydrostatic mode that resolves depth-averaged intra-wave motions explicitly (de Ridder et al., 2021). However, this mode did not have a suitable sediment transport module to resolve intra-wave sediment transport and morphological changes. Here, the Van Rijn (2007) equations for bed load and suspended transport are implemented in a depth- averaged framework for the non-hydrostatic version of XBeach in a similar way as done in the Surfbeat mode. In this abstract the newly implemented sediment transport formulations are presented and validated with large-scale detailed laboratory experiments of dune erosion under extreme storms.
- 29 May 2025
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 38,p. 54
Open AccessIMPLEMENTATION AND VALIDATION OF AN INTRA-WAVE SEDIMENT TRANSPORT MODULE IN A DEPTH-AVERAGED NON-HYDROSTATIC WAVE MODEL
XBeach (Roelvink et al., 2009) is an open-source numerical model which simulates hydrodynamic and morphodynamic processes and impacts on coasts on the time scale of storms. The original model approach (Surfbeat mode) explicitly solves wave group and long wave (infragravity) dynamics but parameterizes the intra- wave motions of short (sea-swell) waves. On steep beaches and on coastal structures, this parameterization leads to substantial underestimation of wave run-up (e.g., De Beer et al., 2021) and overtopping (Roelvink et al., 2018). Recently, the model was therefore extended with a non-hydrostatic mode that resolves depth-averaged intra-wave motions explicitly (de Ridder et al., 2021). However, this mode did not have a suitable sediment transport module to resolve intra-wave sediment transport and morphological changes. Here, the Van Rijn (2007) equations for bed load and suspended transport are implemented in a depth- averaged framework for the non-hydrostatic version of XBeach in a similar way as done in the Surfbeat mode. In this abstract the newly implemented sediment transport formulations are presented and validated with large-scale detailed laboratory experiments of dune erosion under extreme storms.
- Open Access
- 6 February 2025
- Published by Elsevier in Coastal Engineering
- Vol. 198
Individual overtopping volumes, water layer thickness and front velocities at rubble mound breakwaters with a smooth crest in shallow water
- 6 February 2025
- Published by Elsevier in Coastal Engineering
- Vol. 198
Open AccessIndividual overtopping volumes, water layer thickness and front velocities at rubble mound breakwaters with a smooth crest in shallow water
- Open Access
- 23 December 2024
- Published by TU Delft OPEN Publishing in Journal of Coastal and Hydraulic Structures
- Vol. 4
Validation of an efficient two-layer non-hydrostatic wave model on a sloping foreshore
In the physical modelling of coastal engineering problems, use is often made of foreshores and transition slopes to obtain the desired wave conditions - both spectral parameters and wave height distribution - at a given location. Numerical wave models can be used to predict whether the target wave conditions are met for a given physical model layout and wave forcing. The XBeach non-hydrostatic two-layer model is a computationally efficient numerical model that has been validated for spectral wave parameters, but lacks validation of the simulated wave height distributions. In this work, wave flume data with high spatial density over a sloping foreshore is used to validate the ability of this numerical model to reproduce both spectral wave parameters and wave height distributions. As part of this effort, optimal settings have been derived for the wave breaking formulation used in the numerical model, resulting in recommended values for the maxbrsteep and reformsteep parameters of 0.40 and 0.20 respectively. From the results of the validation it is concluded that the numerical model is unsuccessful in reproducing the validation tests with 5.0% wave steepness, potentially due to the higher kph numbers on the generating model boundary. Hence, using the numerical model with values of kph ≥ 2 on the model boundary is not recommended. The XBeach non-hydrostatic two-layer model performs much better for the 1.0% and 2.5% wave steepness tests, where the spectral wave parameters are represented well. The corresponding wave height distributions are represented reasonably well up to the point that the relative water depth gets very shallow. For shallower water, the model is expected to underestimate the higher waves in the wave height distribution. Additionally, the numerical model is shown to reproduce the wave height distribution better than a commonly used analytical formulation for wave height distributions on slopes.
- 23 December 2024
- Published by TU Delft OPEN Publishing in Journal of Coastal and Hydraulic Structures
- Vol. 4
Open AccessValidation of an efficient two-layer non-hydrostatic wave model on a sloping foreshore
In the physical modelling of coastal engineering problems, use is often made of foreshores and transition slopes to obtain the desired wave conditions - both spectral parameters and wave height distribution - at a given location. Numerical wave models can be used to predict whether the target wave conditions are met for a given physical model layout and wave forcing. The XBeach non-hydrostatic two-layer model is a computationally efficient numerical model that has been validated for spectral wave parameters, but lacks validation of the simulated wave height distributions. In this work, wave flume data with high spatial density over a sloping foreshore is used to validate the ability of this numerical model to reproduce both spectral wave parameters and wave height distributions. As part of this effort, optimal settings have been derived for the wave breaking formulation used in the numerical model, resulting in recommended values for the maxbrsteep and reformsteep parameters of 0.40 and 0.20 respectively. From the results of the validation it is concluded that the numerical model is unsuccessful in reproducing the validation tests with 5.0% wave steepness, potentially due to the higher kph numbers on the generating model boundary. Hence, using the numerical model with values of kph ≥ 2 on the model boundary is not recommended. The XBeach non-hydrostatic two-layer model performs much better for the 1.0% and 2.5% wave steepness tests, where the spectral wave parameters are represented well. The corresponding wave height distributions are represented reasonably well up to the point that the relative water depth gets very shallow. For shallower water, the model is expected to underestimate the higher waves in the wave height distribution. Additionally, the numerical model is shown to reproduce the wave height distribution better than a commonly used analytical formulation for wave height distributions on slopes.
- Open Access
- 27 September 2024
- Published by Elsevier in Coastal Engineering
- Vol. 194
Wave overtopping discharges at rubble mound structures in shallow water
- 27 September 2024
- Published by Elsevier in Coastal Engineering
- Vol. 194
Open AccessWave overtopping discharges at rubble mound structures in shallow water
- Open Access
- 2 May 2024
- Published by TU Delft OPEN Publishing in CoastLab 2024: Physical Modelling in Coastal Engineering and Science
Validation Of A Nonlinear Wave Decompistion Method Including Shoaling
It is important to decompose the incident and the reflected waves when performing physical or numerical experiments in a wave flume. Especially when large reflection is expected, from for example a breakwater, the total measured signal can significantly deviate from the incident signal. Different techniques exist to decompose a signal into incident and reflected signals. For 1D wave flumes a method based on co-located wave gauges (Nwogu, 1989) or multiple wave gauges (Røge Eldrup and Lykke Andersen, 2019, Zelt and Skjelbreia, 1993) is commonly applied. The latter is the focus of this abstract since recently, the decomposition method based on multiple wave gauges was extended to be applicable to nonlinear irregular waves by including bound waves and amplitude dispersion (Eldrup and Lykke Andersen, 2019). Moreover, the practical requirements for the nonlinear wave decomposition methods were described in De Ridder et al. (2023). Most of the nonlinear wave decomposition methods are only applicable to a flat bed and will introduce an error when it is applied on a sloping foreshore which is typically the case in physical model experiments. Padilla and Alsina (2020) derived a general framework including shoaling of bound waves and Lykke Andersen and Eldrup (2021) presented a method for nonlinear regular waves over a sloping bed. However, a nonlinear decomposition method for irregular waves over a sloping bed has never been verified with physical model experiments. In this abstract the nonlinear decomposition method for irregular waves as presented in De Ridder et al. (2023) is extended with the effects of shoaling and its effects are verified with a physical model experiment.
- 2 May 2024
- Published by TU Delft OPEN Publishing in CoastLab 2024: Physical Modelling in Coastal Engineering and Science
Open AccessValidation Of A Nonlinear Wave Decompistion Method Including Shoaling
It is important to decompose the incident and the reflected waves when performing physical or numerical experiments in a wave flume. Especially when large reflection is expected, from for example a breakwater, the total measured signal can significantly deviate from the incident signal. Different techniques exist to decompose a signal into incident and reflected signals. For 1D wave flumes a method based on co-located wave gauges (Nwogu, 1989) or multiple wave gauges (Røge Eldrup and Lykke Andersen, 2019, Zelt and Skjelbreia, 1993) is commonly applied. The latter is the focus of this abstract since recently, the decomposition method based on multiple wave gauges was extended to be applicable to nonlinear irregular waves by including bound waves and amplitude dispersion (Eldrup and Lykke Andersen, 2019). Moreover, the practical requirements for the nonlinear wave decomposition methods were described in De Ridder et al. (2023). Most of the nonlinear wave decomposition methods are only applicable to a flat bed and will introduce an error when it is applied on a sloping foreshore which is typically the case in physical model experiments. Padilla and Alsina (2020) derived a general framework including shoaling of bound waves and Lykke Andersen and Eldrup (2021) presented a method for nonlinear regular waves over a sloping bed. However, a nonlinear decomposition method for irregular waves over a sloping bed has never been verified with physical model experiments. In this abstract the nonlinear decomposition method for irregular waves as presented in De Ridder et al. (2023) is extended with the effects of shoaling and its effects are verified with a physical model experiment.
- Open Access
- 11 May 2023
- Published by Elsevier in Applied Ocean Research
- Vol. 136
Hybrid modelling to improve operational wave forecasts by combining process-based and machine learning models
- 11 May 2023
- Published by Elsevier in Applied Ocean Research
- Vol. 136
Open AccessHybrid modelling to improve operational wave forecasts by combining process-based and machine learning models
- Open Access
- 4 April 2023
- Published by Elsevier in Coastal Engineering
- Vol. 183
Validation and practical application of nonlinear wave decomposition methods for irregular waves
- 4 April 2023
- Published by Elsevier in Coastal Engineering
- Vol. 183
Open AccessValidation and practical application of nonlinear wave decomposition methods for irregular waves
- 1 June 2020
- Published by Elsevier in Coastal Engineering
- Vol. 158
Deep learning video analysis as measurement technique in physical models
- 1 June 2020
- Published by Elsevier in Coastal Engineering
- Vol. 158
Deep learning video analysis as measurement technique in physical models