Ashkan Behnam
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ashkan Behnam has a total of 68 co-authors. Here are the top co-authors by number of shared publications:
- Ant Ural
University of Florida
18 shared publications - Eric Pop
Stanford University
8 shared publications Gijs Bosman
University of Florida 1 Department of Electrical and Computer Engineering Gainesville, Florida 32611, USA
5 shared publicationsJason L. Johnson
University of Florida 1 Department of Electrical and Computer Engineering Gainesville, Florida 32611, USA
3 shared publications- Roman Sordan
L-NESS, Department of Physics, Politecnico di Milano, Como, ITALY
3 shared publications - Yanbin An
University of Florida 1 Department of Electrical and Computer Engineering Gainesville, Florida 32611, USA
3 shared publications
Latest Publications
- Open Access
- 20 February 2018
- Published by IOP Publishing in 2D Materials
- Vol. 5 (2) , 025014
Ultra-low contact resistance in graphene devices at the Dirac point
- 20 February 2018
- Published by IOP Publishing in 2D Materials
- Vol. 5 (2) , 025014
Open AccessUltra-low contact resistance in graphene devices at the Dirac point
- Open Access
- 25 May 2017
- Published by Springer Nature in Scientific Reports
- Vol. 7 (1) , 1-7
High-Gain Graphene Transistors with a Thin AlOx Top-Gate Oxide
The high-frequency performance of transistors is usually assessed by speed and gain figures of merit, such as the maximum oscillation frequency fmax, cutoff frequency fT, ratio fmax/fT, forward transmission coefficient S21, and open-circuit voltage gain Av. All these figures of merit must be as large as possible for transistors to be useful in practical electronics applications. Here we demonstrate high-performance graphene field-effect transistors (GFETs) with a thin AlOx gate dielectric which outperform previous state-of-the-art GFETs: we obtained fmax/fT > 3, Av > 30 dB, and S21 = 12.5 dB (at 10 MHz and depending on the transistor geometry) from S-parameter measurements. A dc characterization of GFETs in ambient conditions reveals good current saturation and relatively large transconductance ~600 S/m. The realized GFETs offer the prospect of using graphene in a much wider range of electronic applications which require substantial gain.
- 25 May 2017
- Published by Springer Nature in Scientific Reports
- Vol. 7 (1) , 1-7
Open AccessHigh-Gain Graphene Transistors with a Thin AlOx Top-Gate Oxide
The high-frequency performance of transistors is usually assessed by speed and gain figures of merit, such as the maximum oscillation frequency fmax, cutoff frequency fT, ratio fmax/fT, forward transmission coefficient S21, and open-circuit voltage gain Av. All these figures of merit must be as large as possible for transistors to be useful in practical electronics applications. Here we demonstrate high-performance graphene field-effect transistors (GFETs) with a thin AlOx gate dielectric which outperform previous state-of-the-art GFETs: we obtained fmax/fT > 3, Av > 30 dB, and S21 = 12.5 dB (at 10 MHz and depending on the transistor geometry) from S-parameter measurements. A dc characterization of GFETs in ambient conditions reveals good current saturation and relatively large transconductance ~600 S/m. The realized GFETs offer the prospect of using graphene in a much wider range of electronic applications which require substantial gain.
- 28 November 2016
- Published by AIP Publishing in Applied Physics Letters
- Vol. 109 (22) , 223104
Gate tunneling current and quantum capacitance in metal-oxide-semiconductor devices with graphene gate electrodes
Metal-oxide-semiconductor (MOS) devices with graphene as the metal gate electrode, silicon dioxide with thicknesses ranging from 5 to 20 nm as the dielectric, and p-type silicon as the semiconductor are fabricated and characterized. It is found that Fowler-Nordheim (F-N) tunneling dominates the gate tunneling current in these devices for oxide thicknesses of 10 nm and larger, whereas for devices with 5 nm oxide, direct tunneling starts to play a role in determining the total gate current. Furthermore, the temperature dependences of the F-N tunneling current for the 10 nm devices are characterized in the temperature range 77–300 K. The F-N coefficients and the effective tunneling barrier height are extracted as a function of temperature. It is found that the effective barrier height decreases with increasing temperature, which is in agreement with the results previously reported for conventional MOS devices with polysilicon or metal gate electrodes. In addition, high frequency capacitance-voltage measurements of these MOS devices are performed, which depict a local capacitance minimum under accumulation for thin oxides. By analyzing the data using numerical calculations based on the modified density of states of graphene in the presence of charged impurities, it is shown that this local minimum is due to the contribution of the quantum capacitance of graphene. Finally, the workfunction of the graphene gate electrode is extracted by determining the flat-band voltage as a function of oxide thickness. These results show that graphene is a promising candidate as the gate electrode in metal-oxide-semiconductor devices.
- 28 November 2016
- Published by AIP Publishing in Applied Physics Letters
- Vol. 109 (22) , 223104
Gate tunneling current and quantum capacitance in metal-oxide-semiconductor devices with graphene gate electrodes
Metal-oxide-semiconductor (MOS) devices with graphene as the metal gate electrode, silicon dioxide with thicknesses ranging from 5 to 20 nm as the dielectric, and p-type silicon as the semiconductor are fabricated and characterized. It is found that Fowler-Nordheim (F-N) tunneling dominates the gate tunneling current in these devices for oxide thicknesses of 10 nm and larger, whereas for devices with 5 nm oxide, direct tunneling starts to play a role in determining the total gate current. Furthermore, the temperature dependences of the F-N tunneling current for the 10 nm devices are characterized in the temperature range 77–300 K. The F-N coefficients and the effective tunneling barrier height are extracted as a function of temperature. It is found that the effective barrier height decreases with increasing temperature, which is in agreement with the results previously reported for conventional MOS devices with polysilicon or metal gate electrodes. In addition, high frequency capacitance-voltage measurements of these MOS devices are performed, which depict a local capacitance minimum under accumulation for thin oxides. By analyzing the data using numerical calculations based on the modified density of states of graphene in the presence of charged impurities, it is shown that this local minimum is due to the contribution of the quantum capacitance of graphene. Finally, the workfunction of the graphene gate electrode is extracted by determining the flat-band voltage as a function of oxide thickness. These results show that graphene is a promising candidate as the gate electrode in metal-oxide-semiconductor devices.
- 21 September 2015
- Published by AIP Publishing in Applied Physics Letters
- Vol. 107 (12) , 123508
Nanoscale phase change memory with graphene ribbon electrodes
Phase change memory (PCM) devices are known to reduce in power consumption as the bit volume and contact area of their electrodes are scaled down. Here, we demonstrate two types of low-power PCM devices with lateral graphene ribbon electrodes: one in which the graphene is patterned into narrow nanoribbons and the other where the phase change material is patterned into nanoribbons. The sharp graphene “edge” contacts enable switching with threshold voltages as low as ∼3 V, low programming currents (μA SET and μA RESET) and OFF/ON resistance ratios >100. Large-scale fabrication with graphene grown by chemical vapor deposition also enables the study of heterogeneous integration and that of variability for such nanomaterials and devices.
- 21 September 2015
- Published by AIP Publishing in Applied Physics Letters
- Vol. 107 (12) , 123508
Nanoscale phase change memory with graphene ribbon electrodes
Phase change memory (PCM) devices are known to reduce in power consumption as the bit volume and contact area of their electrodes are scaled down. Here, we demonstrate two types of low-power PCM devices with lateral graphene ribbon electrodes: one in which the graphene is patterned into narrow nanoribbons and the other where the phase change material is patterned into nanoribbons. The sharp graphene “edge” contacts enable switching with threshold voltages as low as ∼3 V, low programming currents (μA SET and μA RESET) and OFF/ON resistance ratios >100. Large-scale fabrication with graphene grown by chemical vapor deposition also enables the study of heterogeneous integration and that of variability for such nanomaterials and devices.
- 21 September 2015
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 118 (11) , 114307
Forward-bias diode parameters, electronic noise, and photoresponse of graphene/silicon Schottky junctions with an interfacial native oxide layer
Metal-semiconductor Schottky junction devices composed of chemical vapor deposition grown monolayer graphene on p-type silicon substrates are fabricated and characterized. Important diode parameters, such as the Schottky barrier height, ideality factor, and series resistance, are extracted from forward bias current-voltage characteristics using a previously established method modified to take into account the interfacial native oxide layer present at the graphene/silicon junction. It is found that the ideality factor can be substantially increased by the presence of the interfacial oxide layer. Furthermore, low frequency noise of graphene/silicon Schottky junctions under both forward and reverse bias is characterized. The noise is found to be 1/f dominated and the shot noise contribution is found to be negligible. The dependence of the 1/f noise on the forward and reverse current is also investigated. Finally, the photoresponse of graphene/silicon Schottky junctions is studied. The devices exhibit a peak responsivity of around 0.13 A/W and an external quantum efficiency higher than 25%. From the photoresponse and noise measurements, the bandwidth is extracted to be ∼1 kHz and the normalized detectivity is calculated to be cm Hz1/2 W−1. These results provide important insights for the future integration of graphene with silicon device technology.- 21 September 2015
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 118 (11) , 114307
Forward-bias diode parameters, electronic noise, and photoresponse of graphene/silicon Schottky junctions with an interfacial native oxide layer
Metal-semiconductor Schottky junction devices composed of chemical vapor deposition grown monolayer graphene on p-type silicon substrates are fabricated and characterized. Important diode parameters, such as the Schottky barrier height, ideality factor, and series resistance, are extracted from forward bias current-voltage characteristics using a previously established method modified to take into account the interfacial native oxide layer present at the graphene/silicon junction. It is found that the ideality factor can be substantially increased by the presence of the interfacial oxide layer. Furthermore, low frequency noise of graphene/silicon Schottky junctions under both forward and reverse bias is characterized. The noise is found to be 1/f dominated and the shot noise contribution is found to be negligible. The dependence of the 1/f noise on the forward and reverse current is also investigated. Finally, the photoresponse of graphene/silicon Schottky junctions is studied. The devices exhibit a peak responsivity of around 0.13 A/W and an external quantum efficiency higher than 25%. From the photoresponse and noise measurements, the bandwidth is extracted to be ∼1 kHz and the normalized detectivity is calculated to be cm Hz1/2 W−1. These results provide important insights for the future integration of graphene with silicon device technology.- 15 April 2015
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 7 (17) , 8076-8083
Scaling of graphene integrated circuits
The scaling of graphene sub-micron integrated circuits was demonstrated by fabricating and characterizing graphene ring oscillators of different gate lengths, exhibiting the highest oscillation frequency of 4.3 GHz obtained in any strictly low-dimensional material to date.
- 15 April 2015
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 7 (17) , 8076-8083
Scaling of graphene integrated circuits
The scaling of graphene sub-micron integrated circuits was demonstrated by fabricating and characterizing graphene ring oscillators of different gate lengths, exhibiting the highest oscillation frequency of 4.3 GHz obtained in any strictly low-dimensional material to date.
- 6 February 2013
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 13 (10) , 4581-4586
High-Field Electrical and Thermal Transport in Suspended Graphene
We study the intrinsic transport properties of suspended graphene devices at high fields (≥1 V/μm) and high temperatures (≥1000 K). Across 15 samples, we find peak (average) saturation velocity of 3.6 × 107 cm/s (1.7 × 107 cm/s) and peak (average) thermal conductivity of 530 W m–1 K–1 (310 W m–1 K–1) at 1000 K. The saturation velocity is 2–4 times and the thermal conductivity 10–17 times greater than in silicon at such elevated temperatures. However, the thermal conductivity shows a steeper decrease at high temperature than in graphite, consistent with stronger effects of second-order three-phonon scattering. Our analysis of sample-to-sample variation suggests the behavior of “cleaner” devices most closely approaches the intrinsic high-field properties of graphene. This study reveals key features of charge and heat flow in graphene up to device breakdown at ∼2230 K in vacuum, highlighting remaining unknowns under extreme operating conditions.
- 6 February 2013
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 13 (10) , 4581-4586
High-Field Electrical and Thermal Transport in Suspended Graphene
We study the intrinsic transport properties of suspended graphene devices at high fields (≥1 V/μm) and high temperatures (≥1000 K). Across 15 samples, we find peak (average) saturation velocity of 3.6 × 107 cm/s (1.7 × 107 cm/s) and peak (average) thermal conductivity of 530 W m–1 K–1 (310 W m–1 K–1) at 1000 K. The saturation velocity is 2–4 times and the thermal conductivity 10–17 times greater than in silicon at such elevated temperatures. However, the thermal conductivity shows a steeper decrease at high temperature than in graphite, consistent with stronger effects of second-order three-phonon scattering. Our analysis of sample-to-sample variation suggests the behavior of “cleaner” devices most closely approaches the intrinsic high-field properties of graphene. This study reveals key features of charge and heat flow in graphene up to device breakdown at ∼2230 K in vacuum, highlighting remaining unknowns under extreme operating conditions.
- 7 January 2013
- Published by AIP Publishing in Applied Physics Letters
- Vol. 102 (1) , 013110
Metal-semiconductor-metal photodetectors based on graphene/p-type silicon Schottky junctions
Metal-semiconductor-metal (MSM) photodetectors based on graphene/p-type Si Schottky junctions are fabricated and characterized. Thermionic emission dominates the transport across the junctions above 260 K with a zero-bias barrier height of 0.48 eV. The reverse-bias dependence of the barrier height is found to result mostly from the Fermi level shift in graphene. MSM photodetectors exhibit a responsivity of 0.11 A/W and a normalized photocurrent-to-dark current ratio of 4.55 × 104 mW−1, which are larger than those previously obtained for similar detectors based on carbon nanotubes. These results are important for the integration of transparent, conductive graphene electrodes into existing silicon technologies.
- 7 January 2013
- Published by AIP Publishing in Applied Physics Letters
- Vol. 102 (1) , 013110
Metal-semiconductor-metal photodetectors based on graphene/p-type silicon Schottky junctions
Metal-semiconductor-metal (MSM) photodetectors based on graphene/p-type Si Schottky junctions are fabricated and characterized. Thermionic emission dominates the transport across the junctions above 260 K with a zero-bias barrier height of 0.48 eV. The reverse-bias dependence of the barrier height is found to result mostly from the Fermi level shift in graphene. MSM photodetectors exhibit a responsivity of 0.11 A/W and a normalized photocurrent-to-dark current ratio of 4.55 × 104 mW−1, which are larger than those previously obtained for similar detectors based on carbon nanotubes. These results are important for the integration of transparent, conductive graphene electrodes into existing silicon technologies.
- 15 June 2011
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 109 (12) , 124301
Experimental study of graphitic nanoribbon films for ammonia sensing
We fabricate and study the ammonia sensing properties of graphitic nanoribbon films consisting of multi-layer graphene nanoribbons. These films show very good sensitivity to parts-per-million (ppm) level concentrations of ammonia, which is further enhanced by platinum functionalization, resulting in a relative resistance response of ∼70% when exposed to 50 ppm ammonia. In addition, the sensing response exhibits excellent repeatability and full recovery in air. We also study in detail the dependence of the sensing response on ammonia concentration and temperature. We find that the relative resistance response of the graphitic nanoribbon films shows a power-law dependence on the ammonia concentration, which can be explained based on the Freundlich isotherm. The activation energy obtained from an Arrhenius plot of the temperature-dependent measurements is ∼50 meV, which is consistent with the theoretical calculations of the adsorption energies of ammonia on large graphene sheets and nanoribbons. Their simple and low-cost fabrication process and good sensing response open up the possibility of using graphitic nanoribbon films for large-scale sensing applications.
- 15 June 2011
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 109 (12) , 124301
Experimental study of graphitic nanoribbon films for ammonia sensing
We fabricate and study the ammonia sensing properties of graphitic nanoribbon films consisting of multi-layer graphene nanoribbons. These films show very good sensitivity to parts-per-million (ppm) level concentrations of ammonia, which is further enhanced by platinum functionalization, resulting in a relative resistance response of ∼70% when exposed to 50 ppm ammonia. In addition, the sensing response exhibits excellent repeatability and full recovery in air. We also study in detail the dependence of the sensing response on ammonia concentration and temperature. We find that the relative resistance response of the graphitic nanoribbon films shows a power-law dependence on the ammonia concentration, which can be explained based on the Freundlich isotherm. The activation energy obtained from an Arrhenius plot of the temperature-dependent measurements is ∼50 meV, which is consistent with the theoretical calculations of the adsorption energies of ammonia on large graphene sheets and nanoribbons. Their simple and low-cost fabrication process and good sensing response open up the possibility of using graphitic nanoribbon films for large-scale sensing applications.
- 1 June 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 129-130
Transport properties of CVD-grown graphene nanoribbon field-effect transistors
This work represents the first demonstration of GNR FETs using CVD-grown graphene, a key step towards large-scale integration. CVD GNRs are comparable to the best state-of-the-art GNRs obtained by other methods, and can support current densities up to ~3 mA/μm. Presenting data from 22 samples, this work also serves to identify key future challenges, such as device variability.
- 1 June 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 129-130
Transport properties of CVD-grown graphene nanoribbon field-effect transistors
This work represents the first demonstration of GNR FETs using CVD-grown graphene, a key step towards large-scale integration. CVD GNRs are comparable to the best state-of-the-art GNRs obtained by other methods, and can support current densities up to ~3 mA/μm. Presenting data from 22 samples, this work also serves to identify key future challenges, such as device variability.