Sergei Andreevich Boronin
Research Subjects
Sergei Andreevich Boronin has a total of 79 co-authors. Here are the top co-authors by number of shared publications:
A.A. Osiptsov
9 shared publications- Alexander N. Osiptsov
Institute of Mechanics, Moscow State University, Moscow, Russia
6 shared publications A. A. Osiptsov
SKOLTECH
3 shared publications- Andrei A. Osiptsov
Skolkovo Institute of Science and Technology (Skoltech) 3 Nobel Street 143026 Moscow Russian Federation
3 shared publications Andrei Osiptsov
Skolkovo Institute of Science and Technology
3 shared publicationsI.A. Garagash
3 shared publications
Latest Publications
- Open Access
- 1 October 2024
- Published by KEAI Publishing in Petroleum Science
- Vol. 21 (5) , 3237-3257
On the efficient non-linear solver for hydraulic fracturing and well cementing simulations based on Anderson acceleration
- 1 October 2024
- Published by KEAI Publishing in Petroleum Science
- Vol. 21 (5) , 3237-3257
Open AccessOn the efficient non-linear solver for hydraulic fracturing and well cementing simulations based on Anderson acceleration
- 21 March 2024
- Published by Springer Nature
- p. 1622-1632
Integrated Approach to Optimize Flowback in Multi-stage Hydraulically Fractured Wells
- 21 March 2024
- Published by Springer Nature
- p. 1622-1632
Integrated Approach to Optimize Flowback in Multi-stage Hydraulically Fractured Wells
- Open Access
- 1 August 2023
- Published by KEAI Publishing in Petroleum Science
- Vol. 20 (4) , 2202-2231
Integrated modeling of fracturing-flowback-production dynamics and calibration on field data: Optimum well startup scenarios
- 1 August 2023
- Published by KEAI Publishing in Petroleum Science
- Vol. 20 (4) , 2202-2231
Open AccessIntegrated modeling of fracturing-flowback-production dynamics and calibration on field data: Optimum well startup scenarios
- 15 March 2022
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 27 (04) , 2126-2144
Proppant Packing Near the Fracture Tip during Tip Screenout: Asymptotic Models for Pressure Buildup Calibrated on Field Data and Verified with Two-Continua Simulations
Summary: We analyze pressure slopes during buildup when proppant placement into a fracture results in tip screenout (TSO), as observed in real field data on pumping of fracturing jobs. The phenomenon is described by proppant packing and jamming near the fracture tip, leading to TSO. Transient evolution of the zone of packed proppant near the tip and associated additional pressure drop along the packed bank are evaluated. Under the assumption of constant fracture height, the additional pressure drop during TSO grows as t(1+α), where tα is the law of proppant concentration growth (pressure drop grows quadratically in time, if the proppant concentration on surface at the blender grows linearly in time). The model is calibrated on field data from fracturing jobs in Western Siberia, Russia. These approximate models are verified with the two-continua model of proppant transport used to describe the process of proppant packing and jamming near the fracture tip. We also show how predictions of bottomhole pressure (BHP) growth during TSO obtained using proppant transport models implemented into existing hydraulic fracturing simulators can be significantly improved by a reasonable (based on behavior of dense suspensions at the packing limit) modification to parameters, describing suspension shear viscosity.
- 15 March 2022
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 27 (04) , 2126-2144
Proppant Packing Near the Fracture Tip during Tip Screenout: Asymptotic Models for Pressure Buildup Calibrated on Field Data and Verified with Two-Continua Simulations
Summary: We analyze pressure slopes during buildup when proppant placement into a fracture results in tip screenout (TSO), as observed in real field data on pumping of fracturing jobs. The phenomenon is described by proppant packing and jamming near the fracture tip, leading to TSO. Transient evolution of the zone of packed proppant near the tip and associated additional pressure drop along the packed bank are evaluated. Under the assumption of constant fracture height, the additional pressure drop during TSO grows as t(1+α), where tα is the law of proppant concentration growth (pressure drop grows quadratically in time, if the proppant concentration on surface at the blender grows linearly in time). The model is calibrated on field data from fracturing jobs in Western Siberia, Russia. These approximate models are verified with the two-continua model of proppant transport used to describe the process of proppant packing and jamming near the fracture tip. We also show how predictions of bottomhole pressure (BHP) growth during TSO obtained using proppant transport models implemented into existing hydraulic fracturing simulators can be significantly improved by a reasonable (based on behavior of dense suspensions at the packing limit) modification to parameters, describing suspension shear viscosity.
- Open Access
- 12 October 2021
- Published by Society of Petroleum Engineers (SPE)
Development of Deep Transformer-Based Models for Long-Term Prediction of Transient Production of Oil Wells
We propose a novel approach to data-driven modeling of a transient production of oil wells. We apply the transformer-based neural networks trained on the multivariate time series composed of various parameters of oil wells measured during their exploitation. By tuning the machine learning models for a single well (ignoring the effect of neighboring wells) on the open-source field datasets, we demonstrate that transformer outperforms recurrent neural networks with LSTM/GRU cells in the forecasting of the bottomhole pressure dynamics. We apply the transfer learning procedure to the transformer-based surrogate model, which includes the initial training on the dataset from a certain well and additional tuning of the model's weights on the dataset from a target well. Transfer learning approach helps to improve the prediction capability of the model. Next, we generalize the single-well model based on the transformer architecture for multiple wells to simulate complex transient oilfield-level patterns. In other words, we create the global model which deals with the dataset, comprised of the production history from multiple wells, and allows for capturing the well interference resulting in more accurate prediction of the bottomhole pressure or flow rate evolutions for each well under consideration. The developed instruments for a single-well and oilfield-scale modelling can be used to optimize the production process by selecting the operating regime and submersible equipment to increase the hydrocarbon recovery. In addition, the models can be helpful to perform well-testing avoiding costly shut-in operations.
- 12 October 2021
- Published by Society of Petroleum Engineers (SPE)
Open AccessDevelopment of Deep Transformer-Based Models for Long-Term Prediction of Transient Production of Oil Wells
We propose a novel approach to data-driven modeling of a transient production of oil wells. We apply the transformer-based neural networks trained on the multivariate time series composed of various parameters of oil wells measured during their exploitation. By tuning the machine learning models for a single well (ignoring the effect of neighboring wells) on the open-source field datasets, we demonstrate that transformer outperforms recurrent neural networks with LSTM/GRU cells in the forecasting of the bottomhole pressure dynamics. We apply the transfer learning procedure to the transformer-based surrogate model, which includes the initial training on the dataset from a certain well and additional tuning of the model's weights on the dataset from a target well. Transfer learning approach helps to improve the prediction capability of the model. Next, we generalize the single-well model based on the transformer architecture for multiple wells to simulate complex transient oilfield-level patterns. In other words, we create the global model which deals with the dataset, comprised of the production history from multiple wells, and allows for capturing the well interference resulting in more accurate prediction of the bottomhole pressure or flow rate evolutions for each well under consideration. The developed instruments for a single-well and oilfield-scale modelling can be used to optimize the production process by selecting the operating regime and submersible equipment to increase the hydrocarbon recovery. In addition, the models can be helpful to perform well-testing avoiding costly shut-in operations.
- 26 October 2020
- Published by Society of Petroleum Engineers (SPE)
Field Testing of the Flowback Technology for Multistage-Fractured Horizontal Wells: Test Results and Primary Interpretation of the Results
The paper presents the results of applying the methodology of well flowback and startup after hydraulic fracturing (HF), previously proposed in (Osiptsov et al., 2019), where the preferred conditions for well flowback after hydraulic fracturing are formulated in the form of a field experiment program. The program was implemented in 2019-2020 at four out of ten wells of the Priobskoye field in Western Siberia. The comparison of the two well clean-up designs, "smooth" and "aggressive", aimed to confirm the hypothesis that the choice of a "smooth" mode can reduce undesirable geomechanical effects to preserve the fracture conductivity and increase the recovery. Adapting our own hydrodynamic and geomechanical models to actual data made it possible to control the well clean-up process in the wells of a field experiment. Well site supervision allowed authors to fully implement the research plan, and also provided the opportunity to vary the parameters of the experiment (adjusting flowrate over time, adjusting the sampling and measurement schedules) using history matched models with actual parameters of the wells. Based on the results, the obtained data were analyzed and interpreted: flow rate, water cut, bottomhole and wellhead pressure, bottomhole temperature, suspended particulate matter (SPM) concentration, drain level, expedition pump frequency and wellhead samples. At the planning stage of the experiment, a formation zone of interest (ZOI) was selected with a set of first six pilot wells, where the geomechanical effects during the flowback period have the greatest impact on production. The field experiment program, which contains the wellhead choke steps sequence of diameters and duration of the well clean-up periods for two scenarios - "aggressive" and "smooth" for particular well. In addition to the choke schedule during eruptive period, there is a need to continue the recommended well startup after the ESP run in hole (RIH). Representativeness and repeatability conditions of field tests were formulated, comparison metrics were developed in order to standardize, normalize and estimate the well performance of the well startup a. We carried out the design of a field experiment proposed in 2019 (Osiptsov et al., 2019) and showed in practice that the dynamics of the well flowback and startup affects the well productivity index for a selected ZOI. In addition, we history-matched in-house geomechanical and hydrodynamic in order to quantify the production increase with regards to different flowback scenarios. Based on the available data, the boundaries of the pressure fluctuations opposite the hydraulic fracturing ports in the horizontal well were calculated in the absence of actual measurements to clarify the conditions for maintaining the conductivity of the fracture.
- 26 October 2020
- Published by Society of Petroleum Engineers (SPE)
Field Testing of the Flowback Technology for Multistage-Fractured Horizontal Wells: Test Results and Primary Interpretation of the Results
The paper presents the results of applying the methodology of well flowback and startup after hydraulic fracturing (HF), previously proposed in (Osiptsov et al., 2019), where the preferred conditions for well flowback after hydraulic fracturing are formulated in the form of a field experiment program. The program was implemented in 2019-2020 at four out of ten wells of the Priobskoye field in Western Siberia. The comparison of the two well clean-up designs, "smooth" and "aggressive", aimed to confirm the hypothesis that the choice of a "smooth" mode can reduce undesirable geomechanical effects to preserve the fracture conductivity and increase the recovery. Adapting our own hydrodynamic and geomechanical models to actual data made it possible to control the well clean-up process in the wells of a field experiment. Well site supervision allowed authors to fully implement the research plan, and also provided the opportunity to vary the parameters of the experiment (adjusting flowrate over time, adjusting the sampling and measurement schedules) using history matched models with actual parameters of the wells. Based on the results, the obtained data were analyzed and interpreted: flow rate, water cut, bottomhole and wellhead pressure, bottomhole temperature, suspended particulate matter (SPM) concentration, drain level, expedition pump frequency and wellhead samples. At the planning stage of the experiment, a formation zone of interest (ZOI) was selected with a set of first six pilot wells, where the geomechanical effects during the flowback period have the greatest impact on production. The field experiment program, which contains the wellhead choke steps sequence of diameters and duration of the well clean-up periods for two scenarios - "aggressive" and "smooth" for particular well. In addition to the choke schedule during eruptive period, there is a need to continue the recommended well startup after the ESP run in hole (RIH). Representativeness and repeatability conditions of field tests were formulated, comparison metrics were developed in order to standardize, normalize and estimate the well performance of the well startup a. We carried out the design of a field experiment proposed in 2019 (Osiptsov et al., 2019) and showed in practice that the dynamics of the well flowback and startup affects the well productivity index for a selected ZOI. In addition, we history-matched in-house geomechanical and hydrodynamic in order to quantify the production increase with regards to different flowback scenarios. Based on the available data, the boundaries of the pressure fluctuations opposite the hydraulic fracturing ports in the horizontal well were calculated in the absence of actual measurements to clarify the conditions for maintaining the conductivity of the fracture.
- 1 May 2020
- Published by Elsevier in Journal of Petroleum Science and Engineering
- Vol. 188
Impact of Flowback Dynamics on Fracture Conductivity
- 1 May 2020
- Published by Elsevier in Journal of Petroleum Science and Engineering
- Vol. 188
Impact of Flowback Dynamics on Fracture Conductivity
- 1 February 2020
- Published by AIP Publishing in Physics of Fluids
- Vol. 32 (2) , 024104
Stability of a vertical Couette flow in the presence of settling particles
We consider the linear stability of a particle-laden vertical Couette flow between two flat plates. The flow is described in the framework of a two-fluid approach with a negligibly small volume fraction of the dispersed phase (the “dusty-gas model”). The carrier-fluid velocity profile in the main flow is modified by the presence of settling particles distributed non-uniformly between the plates. Two types of particle number density distributions are considered, namely, a single layer with a maximum at the flow center line and two symmetric layers located between the center line and the walls. Linearized governing equations are reduced to a modified Orr–Sommerfeld equation for the amplitude of a disturbance in the form of a normal mode. On the basis of a parametric study of the eigenvalues, it is shown that, in contrast to the case of two-phase Couette flow with zero particle velocity slip, the vertical disperse flow is unstable over a wide range of governing parameters, including small Reynolds numbers. In flows with both kinds of particle concentration profiles considered, there are two types of growing modes. A gravitational mode is triggered at low Reynolds numbers and typically small wavenumbers, while a shear mode with the wavelength of the order of the channel width and larger time-amplification rates is triggered at large Reynolds numbers. It is found that both modes are amplified with an increase in the particle mass loading or the ratio of the Reynolds number to squared Froude number, determining the carrier-fluid velocity profile. The results of the study can be used to control the stability of various technological processes involving particle-laden flows.
- 1 February 2020
- Published by AIP Publishing in Physics of Fluids
- Vol. 32 (2) , 024104
Stability of a vertical Couette flow in the presence of settling particles
We consider the linear stability of a particle-laden vertical Couette flow between two flat plates. The flow is described in the framework of a two-fluid approach with a negligibly small volume fraction of the dispersed phase (the “dusty-gas model”). The carrier-fluid velocity profile in the main flow is modified by the presence of settling particles distributed non-uniformly between the plates. Two types of particle number density distributions are considered, namely, a single layer with a maximum at the flow center line and two symmetric layers located between the center line and the walls. Linearized governing equations are reduced to a modified Orr–Sommerfeld equation for the amplitude of a disturbance in the form of a normal mode. On the basis of a parametric study of the eigenvalues, it is shown that, in contrast to the case of two-phase Couette flow with zero particle velocity slip, the vertical disperse flow is unstable over a wide range of governing parameters, including small Reynolds numbers. In flows with both kinds of particle concentration profiles considered, there are two types of growing modes. A gravitational mode is triggered at low Reynolds numbers and typically small wavenumbers, while a shear mode with the wavelength of the order of the channel width and larger time-amplification rates is triggered at large Reynolds numbers. It is found that both modes are amplified with an increase in the particle mass loading or the ratio of the Reynolds number to squared Froude number, determining the carrier-fluid velocity profile. The results of the study can be used to control the stability of various technological processes involving particle-laden flows.
- 1 July 2019
- Published by Elsevier in Journal of Petroleum Science and Engineering
- Vol. 178, 408-418
Formation damage and cleanup in the vicinity of flooding wells: Multi-fluid suspension flow model and calibration on lab data
- 1 July 2019
- Published by Elsevier in Journal of Petroleum Science and Engineering
- Vol. 178, 408-418
Formation damage and cleanup in the vicinity of flooding wells: Multi-fluid suspension flow model and calibration on lab data
- Open Access
- 19 June 2019
- Published by The Royal Society in Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Vol. 475 (2226) , 20190039
Lubrication model of suspension flow in a hydraulic fracture with frictional rheology for shear-induced migration and jamming
We developed a model for suspension flow in a hydraulic fracture, taking into account frictional rheology to capture the effects of shear-induced particle migration, jamming and transition to close packing. One of the key issues with the existing slurry rheology models is that each of them diverges near the close packing limit, which is typically resolved in numerical simulations via a pragmatic (and mostly unjustified) regularization. Another drawback of the family of existing models for proppant transport in fractures is the assumption of a uniform cross-flow concentration profile, which neglects the effects of shear-induced migration. We developed a self-consistent model for slurry flow with a constitutive relation for suspension rheology, which is applicable in the entire range of particle volume concentration, from dilute suspension through dense suspension to the close packing limit. In addition, we investigated the influence of various constitutive relations for the suspension rheology on the final model for the slurry flow. The selected model for slurry flow was implemented into a two-dimensional lubrication model of proppant transport in a fracture (based on the two-continua approach), and illustrative simulations were conducted in comparison with the family of existing suspension rheology models (having a singularity). Validation against laboratory experiments is discussed.
- 19 June 2019
- Published by The Royal Society in Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Vol. 475 (2226) , 20190039
Open AccessLubrication model of suspension flow in a hydraulic fracture with frictional rheology for shear-induced migration and jamming
We developed a model for suspension flow in a hydraulic fracture, taking into account frictional rheology to capture the effects of shear-induced particle migration, jamming and transition to close packing. One of the key issues with the existing slurry rheology models is that each of them diverges near the close packing limit, which is typically resolved in numerical simulations via a pragmatic (and mostly unjustified) regularization. Another drawback of the family of existing models for proppant transport in fractures is the assumption of a uniform cross-flow concentration profile, which neglects the effects of shear-induced migration. We developed a self-consistent model for slurry flow with a constitutive relation for suspension rheology, which is applicable in the entire range of particle volume concentration, from dilute suspension through dense suspension to the close packing limit. In addition, we investigated the influence of various constitutive relations for the suspension rheology on the final model for the slurry flow. The selected model for slurry flow was implemented into a two-dimensional lubrication model of proppant transport in a fracture (based on the two-continua approach), and illustrative simulations were conducted in comparison with the family of existing suspension rheology models (having a singularity). Validation against laboratory experiments is discussed.