Yulia E. Lebedeva
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yulia E. Lebedeva has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
D. V. Grashchenkov
All-Russia Scientific-Research Institute of Aviation Materials (VIAM)
7 shared publications- A. S. Chainikova
All-Russian Scientific Research Institute of Aviation Materials
6 shared publications N. V. Popovich
Russian University of Chemical Technology
6 shared publicationsA. S. Chainikova
National Research Center – Kurchatov Institute (NRC Kurchatov Institute – VIAM), Moscow, Russia
5 shared publicationsL. A. Orlova
Russian University of Chemical Technology
5 shared publicationsM. L. Vaganova
All-Russia Scientific Research Institute of Aviation Materials (VIAM)
5 shared publications
Latest Publications
- 27 July 2022
- Published by Springer Nature in Glass and Ceramics
- Vol. 79 (3-4) , 121-129
Sol-Gel Production of Alkaline-Free Aluminosilicate Glass Ceramic and Investigation of its Properties
- 27 July 2022
- Published by Springer Nature in Glass and Ceramics
- Vol. 79 (3-4) , 121-129
Sol-Gel Production of Alkaline-Free Aluminosilicate Glass Ceramic and Investigation of its Properties
- 1 January 2022
- Published by Pleiades Publishing Ltd in Inorganic Materials
- Vol. 58 (1) , 104-110
Effect of Silicon Carbide Whiskers on the Physicomechanical Properties of ZrB2/SiC Ceramic Composite Materials
ZrB2/(20 – х)SiC/хSiCw (х = 0.5–1.5 vol %) ceramic composite materials have been produced by spark plasma sintering, and their physicomechanical and thermophysical properties have been shown to be influenced by the percentage of the silicon carbide whiskers. The best properties are offered by the ZrB2/SiC ceramic composite material containing 0.5 vol % silicon carbide whiskers. The addition of silicon carbide whiskers has been shown to ensure an increase in apparent density to 99.7% and a reduction in open porosity to 0.13%. Moreover, it increases the microhardness of the composites to 16.4 GPa, their critical stress intensity factor to 5.7 MPa m1/2, and their bending strength to 580 MPa.
- 1 January 2022
- Published by Pleiades Publishing Ltd in Inorganic Materials
- Vol. 58 (1) , 104-110
Effect of Silicon Carbide Whiskers on the Physicomechanical Properties of ZrB2/SiC Ceramic Composite Materials
ZrB2/(20 – х)SiC/хSiCw (х = 0.5–1.5 vol %) ceramic composite materials have been produced by spark plasma sintering, and their physicomechanical and thermophysical properties have been shown to be influenced by the percentage of the silicon carbide whiskers. The best properties are offered by the ZrB2/SiC ceramic composite material containing 0.5 vol % silicon carbide whiskers. The addition of silicon carbide whiskers has been shown to ensure an increase in apparent density to 99.7% and a reduction in open porosity to 0.13%. Moreover, it increases the microhardness of the composites to 16.4 GPa, their critical stress intensity factor to 5.7 MPa m1/2, and their bending strength to 580 MPa.
- 10 November 2021
- Published by Springer Nature in Glass and Ceramics
- Vol. 78 (7-8) , 301-307
Investigation of the Interaction of Y2O3–Al2O3–SiO2 Coatings with Water Vapor and Na2SO4 at Temperatures to 1450°C
- 10 November 2021
- Published by Springer Nature in Glass and Ceramics
- Vol. 78 (7-8) , 301-307
Investigation of the Interaction of Y2O3–Al2O3–SiO2 Coatings with Water Vapor and Na2SO4 at Temperatures to 1450°C
- 6 November 2021
- Published by Springer Nature in Glass and Ceramics
- Vol. 78 (7-8) , 284-287
Investigation of the Effect of SiC-Whisker Content on the Properties of Ceramic Composite Material Obtained by Spark Plasma Sintering (SPS)
- 6 November 2021
- Published by Springer Nature in Glass and Ceramics
- Vol. 78 (7-8) , 284-287
Investigation of the Effect of SiC-Whisker Content on the Properties of Ceramic Composite Material Obtained by Spark Plasma Sintering (SPS)
- Open Access
Erratum: Polozov, I., et al. Fabrication of Silicon Carbide Fiber-Reinforced Silicon Carbide Matrix Composites Using Binder Jetting Additive Manufacturing from Irregularly-Shaped and Spherical Powders. Materials 2020, 13, 1766
The authors wish to make the following correction to this paper
Open AccessErratum: Polozov, I., et al. Fabrication of Silicon Carbide Fiber-Reinforced Silicon Carbide Matrix Composites Using Binder Jetting Additive Manufacturing from Irregularly-Shaped and Spherical Powders. Materials 2020, 13, 1766
The authors wish to make the following correction to this paper
- Open Access
Fabrication of Silicon Carbide Fiber-Reinforced Silicon Carbide Matrix Composites Using Binder Jetting Additive Manufacturing from Irregularly-Shaped and Spherical Powders
In this paper, silicon carbide fiber-reinforced silicon carbide (SiCf/SiC) composites were fabricated using binder jetting additive manufacturing followed by polymer infiltration and pyrolysis. Spherical SiC powders were produced using milling, spray drying, and thermal plasma treatment, and were characterized using SEM and XRD methods. Irregularly shaped and spherical SiC powders were used to obtain SiCf/SiC blends for the application in binder jetting. The effect of SiC powder shape on densification behavior, microstructure, and mechanical properties of binder jetted SiCf/SiC composites was evaluated. The highest density of 2.52 g/cm3 was obtained after six polymer infiltration and pyrolysis cycles. The microstructure and mechanical properties of the fabricated SiCf/SiC composites were characterized. Using the spherical SiC powder resulted in higher fracture toughness and hardness, but lower flexural strength compared to the irregularly shaped powder. It was shown that it is feasible to fabricate dense SiCf/SiC composites using binder jetting followed by polymer infiltration and pyrolysis.
Open AccessFabrication of Silicon Carbide Fiber-Reinforced Silicon Carbide Matrix Composites Using Binder Jetting Additive Manufacturing from Irregularly-Shaped and Spherical Powders
In this paper, silicon carbide fiber-reinforced silicon carbide (SiCf/SiC) composites were fabricated using binder jetting additive manufacturing followed by polymer infiltration and pyrolysis. Spherical SiC powders were produced using milling, spray drying, and thermal plasma treatment, and were characterized using SEM and XRD methods. Irregularly shaped and spherical SiC powders were used to obtain SiCf/SiC blends for the application in binder jetting. The effect of SiC powder shape on densification behavior, microstructure, and mechanical properties of binder jetted SiCf/SiC composites was evaluated. The highest density of 2.52 g/cm3 was obtained after six polymer infiltration and pyrolysis cycles. The microstructure and mechanical properties of the fabricated SiCf/SiC composites were characterized. Using the spherical SiC powder resulted in higher fracture toughness and hardness, but lower flexural strength compared to the irregularly shaped powder. It was shown that it is feasible to fabricate dense SiCf/SiC composites using binder jetting followed by polymer infiltration and pyrolysis.
- 28 January 2019
- Published by Springer Nature in Glass and Ceramics
- Vol. 75 (9-10) , 340-344
Thermophysical Properties of Silicon-Carbide-Based Ceramic Composite Materials Obtained by Spark Plasma Sintering (SPS)
- 28 January 2019
- Published by Springer Nature in Glass and Ceramics
- Vol. 75 (9-10) , 340-344
Thermophysical Properties of Silicon-Carbide-Based Ceramic Composite Materials Obtained by Spark Plasma Sintering (SPS)
- 19 July 2018
- Published by Springer Nature in Glass and Ceramics
- Vol. 75 (3-4) , 133-138
Effect of High Boron Additive Content on SPS-Consolidation and Properties of Commercial Silicon Carbide Powder
- 19 July 2018
- Published by Springer Nature in Glass and Ceramics
- Vol. 75 (3-4) , 133-138
Effect of High Boron Additive Content on SPS-Consolidation and Properties of Commercial Silicon Carbide Powder
- 1 May 2018
- Published by Pleiades Publishing Ltd in Russian Journal of Applied Chemistry
- Vol. 91 (5) , 785-792
Effect of Modifying Additives on the Sintering and Properties of SiC/SiCw Ceramic Composite Material
Spark plasma sintering and hot compaction methods were used to obtain experimental samples of a composite material of the SiC‒SiCw system with various modifying additives (AlN, B4C, HfB2, Y2O3, Al2O3,...
- 1 May 2018
- Published by Pleiades Publishing Ltd in Russian Journal of Applied Chemistry
- Vol. 91 (5) , 785-792
Effect of Modifying Additives on the Sintering and Properties of SiC/SiCw Ceramic Composite Material
Spark plasma sintering and hot compaction methods were used to obtain experimental samples of a composite material of the SiC‒SiCw system with various modifying additives (AlN, B4C, HfB2, Y2O3, Al2O3,...
- 1 May 2018
- Published by Pleiades Publishing Ltd in High Temperature
- Vol. 56 (3) , 378-381
Influence of Nitrogen High-Speed Flow Impact on the Structure and Chemical Composition of High-Temperature Coating on SiC Composite
The impact of the nitrogen high-speed plasma flow on the silicon carbide composite samples (SCC) with high-temperature coating has been studied. The work was performed in a VAT-104 wind tunnel...
- 1 May 2018
- Published by Pleiades Publishing Ltd in High Temperature
- Vol. 56 (3) , 378-381
Influence of Nitrogen High-Speed Flow Impact on the Structure and Chemical Composition of High-Temperature Coating on SiC Composite
The impact of the nitrogen high-speed plasma flow on the silicon carbide composite samples (SCC) with high-temperature coating has been studied. The work was performed in a VAT-104 wind tunnel...