Nirut Konkong
Research Subjects
Nirut Konkong has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Apai Benchaphong
Faculty of Engineering, Rajamangala University of Technology Krungthep, Bangkok 10120, Thailand
2 shared publications- Kampanart Piyathamrongchai
Department of Natural Resources and Environment, Faculty of Agriculture, Natural Resources and Environment, Naresuan University, Phitsanulok 65000, Thailand
2 shared publications - Rapikorn Chalongsuppunyoo
Faculty of Education, Nakhon Sawan Rajabhat University, Nakhon Sawan 60000, Thailand
2 shared publications Rattanasak Hongthong
Faculty of Engineering, Rajamangala University of Technology Krungthep, Bangkok 10120, Thailand
2 shared publications- Rhutairat Hataitara
Department of Natural Resources and Environment, Faculty of Agriculture, Natural Resources and Environment, Naresuan University, Phitsanulok 65000, Thailand
2 shared publications - Sittichai Choosumrong
Department of Natural Resources and Environment, Faculty of Agriculture, Nature Resources and Environment, Naresuan University
2 shared publications
Latest Publications
- Open Access
Development of an IoT-Based Flood Monitoring System Integrated with GIS for Lowland Agricultural Areas
Disaster risk reduction requires efficient flood control in lowland and flood-prone areas, especially in agricultural areas like the Bang Rakam model area in Phitsanulok province, Thailand. In order to improve flood prediction and response, this study proposes the creation of a low-cost, real-time water-level monitoring integrated with spatial data analysis using Geographic Information System (GIS) technology. Ten ultrasonic sensor-equipped monitoring stations were installed thoughtfully around sub-catchment areas to provide highly accurate water-level readings. To define inundation zones and create flood depth maps, the sensors gather flood level data from each station, which is then processed using a 1-m Digital Elevation Model (DEM) and Python-based geospatial analysis. In order to create dynamic flood maps that offer information on flood extent, depth, and water volume within each sub-catchment, an automated method was created to use real-time water-level data. These results demonstrate the promise of low-cost IoT-based flood monitoring devices as an affordable and scalable remedy for communities that are at risk. This method improves knowledge of flood dynamics in the Bang Rakam model area by combining sensor technology and spatial data analysis. It also acts as a standard for flood management tactics in other lowland areas. The study emphasizes how crucial real-time data-driven flood monitoring is to enhancing early-warning systems, disaster preparedness, and water resource management.
Open AccessDevelopment of an IoT-Based Flood Monitoring System Integrated with GIS for Lowland Agricultural Areas
Disaster risk reduction requires efficient flood control in lowland and flood-prone areas, especially in agricultural areas like the Bang Rakam model area in Phitsanulok province, Thailand. In order to improve flood prediction and response, this study proposes the creation of a low-cost, real-time water-level monitoring integrated with spatial data analysis using Geographic Information System (GIS) technology. Ten ultrasonic sensor-equipped monitoring stations were installed thoughtfully around sub-catchment areas to provide highly accurate water-level readings. To define inundation zones and create flood depth maps, the sensors gather flood level data from each station, which is then processed using a 1-m Digital Elevation Model (DEM) and Python-based geospatial analysis. In order to create dynamic flood maps that offer information on flood extent, depth, and water volume within each sub-catchment, an automated method was created to use real-time water-level data. These results demonstrate the promise of low-cost IoT-based flood monitoring devices as an affordable and scalable remedy for communities that are at risk. This method improves knowledge of flood dynamics in the Bang Rakam model area by combining sensor technology and spatial data analysis. It also acts as a standard for flood management tactics in other lowland areas. The study emphasizes how crucial real-time data-driven flood monitoring is to enhancing early-warning systems, disaster preparedness, and water resource management.
- Open Access
- 17 June 2025
- Published by MDPI AG in Preprints.org
Development of an IoT-Based Flood Monitoring System Integrated with GIS for Lowland Agricultural Areas
Disaster risk reduction requires efficient flood control in lowland and flood-prone areas, especially in agricultural areas like Bang Rakam model area in Phitsanulok province, Thailand. In order to improve flood prediction and response, this study proposes the creation of a low-cost, real-time water level monitoring integrated with spatial data analysis using Geographic Information System (GIS) technology. Ten ultrasonic sensor-equipped monitoring stations were installed thoughtfully around sub-catchment areas to provide highly accurate water level readings. To define inundation zones and create flood depth maps, the sensors gather flood level data from each station, which is then processed using a 1-meter Digital Elevation Model (DEM) and Python-based geospatial analysis. In order to create dynamic flood maps that offer information on flood extent, depth, and water volume within each sub-catchment, an automated method was created to use real-time water level data. These results demonstrate the promise of low-cost IoT-based flood monitoring devices as an affordable and scalable remedy for communities that are at risk. This method improves knowledge of flood dynamics in the Bang Rakam model area by combining sensor technology and spatial data analysis. It also acts as a standard for flood management tactics in other lowland areas. The study emphasizes how crucial real-time data-driven flood monitoring is to enhancing early warning systems, disaster preparedness, and water resource management.
- 17 June 2025
- Published by MDPI AG in Preprints.org
Open AccessDevelopment of an IoT-Based Flood Monitoring System Integrated with GIS for Lowland Agricultural Areas
Disaster risk reduction requires efficient flood control in lowland and flood-prone areas, especially in agricultural areas like Bang Rakam model area in Phitsanulok province, Thailand. In order to improve flood prediction and response, this study proposes the creation of a low-cost, real-time water level monitoring integrated with spatial data analysis using Geographic Information System (GIS) technology. Ten ultrasonic sensor-equipped monitoring stations were installed thoughtfully around sub-catchment areas to provide highly accurate water level readings. To define inundation zones and create flood depth maps, the sensors gather flood level data from each station, which is then processed using a 1-meter Digital Elevation Model (DEM) and Python-based geospatial analysis. In order to create dynamic flood maps that offer information on flood extent, depth, and water volume within each sub-catchment, an automated method was created to use real-time water level data. These results demonstrate the promise of low-cost IoT-based flood monitoring devices as an affordable and scalable remedy for communities that are at risk. This method improves knowledge of flood dynamics in the Bang Rakam model area by combining sensor technology and spatial data analysis. It also acts as a standard for flood management tactics in other lowland areas. The study emphasizes how crucial real-time data-driven flood monitoring is to enhancing early warning systems, disaster preparedness, and water resource management.
- Open Access
- 4 November 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (21) , 14530
Probabilistic Analysis of Slope against Uncertain Soil Parameters
The purpose of this article was to investigate the influence of uncertain soil parameters on slope stability problems using the probability method. The most important soil instability is probably the inherent spatial variability of soil properties and its influence on slope safety factors. The probability method is recognized for its validity both in practice and academic research. This method of geotechnical risk management involves uncertain parameters. In this study, randomly selected uncertain parameters were combined with traditional analysis using Bishop’s simple methodology and Monte Carlo simulation. The minimum safety factor and critical slip surface of the slope stability were analyzed by Bishop’s simple method. The influence of uncertain soil parameters was analyzed by the back analysis method with Monte Carlo simulation. The calculation was controlled by a critical slip surface, and the safety factor was equal to 1. The results of the analysis show the minimum safety factor and the significant slippery surface of slope stability with the original soil strength parameters. The new soil strength parameters were recommended by Monte Carlo simulation that was used for improving the soil strength parameters in construction. In addition, probability analysis can identify an insufficient understanding of groundwater level distribution and that the assumption of a uniform distribution increases the probability of failure. Governments can use the results of water level analysis in flood warnings and flood management projects to reduce risks to life and property.
- 4 November 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (21) , 14530
Open AccessProbabilistic Analysis of Slope against Uncertain Soil Parameters
The purpose of this article was to investigate the influence of uncertain soil parameters on slope stability problems using the probability method. The most important soil instability is probably the inherent spatial variability of soil properties and its influence on slope safety factors. The probability method is recognized for its validity both in practice and academic research. This method of geotechnical risk management involves uncertain parameters. In this study, randomly selected uncertain parameters were combined with traditional analysis using Bishop’s simple methodology and Monte Carlo simulation. The minimum safety factor and critical slip surface of the slope stability were analyzed by Bishop’s simple method. The influence of uncertain soil parameters was analyzed by the back analysis method with Monte Carlo simulation. The calculation was controlled by a critical slip surface, and the safety factor was equal to 1. The results of the analysis show the minimum safety factor and the significant slippery surface of slope stability with the original soil strength parameters. The new soil strength parameters were recommended by Monte Carlo simulation that was used for improving the soil strength parameters in construction. In addition, probability analysis can identify an insufficient understanding of groundwater level distribution and that the assumption of a uniform distribution increases the probability of failure. Governments can use the results of water level analysis in flood warnings and flood management projects to reduce risks to life and property.
- 7 July 2022
- Published by Periodica Polytechnica Budapest University of Technology and Economics in Periodica Polytechnica Civil Engineering
- Vol. 66 (4) , 1060-1070
Prediction of In-plane Stiffness for the Cold-formed Steel Frame of the Wall Panel Structure
The purpose of this research was to study the lateral deformation behavior of cold-formed steel wall panel structures using experimental tests, finite element analysis and analytical methods to study the lateral stiffness of these structures. The wall panel structures were tested by full-scale experiments the experimental results of which were verified by a 3D-finite element model. The verification results showed a good correlation between the experimental tests and a finite element model. The single-column spring model was proposed for an elastic lateral stiffness analysis of the cold-formed steel wall panel structures that were formed by combinations of a guide cantilever beam and springs connection. The spring constants were defined by using the stiffness of the stub-chord connection and the bending stiffness of the chord. The experiments tests and finite element analysis were used to verify this single-column spring model. The comparison results showed good agreement between the analytical prediction, finite element analysis and experimental data in the case of the primary type of cold-formed wall structure. The proposed procedure was an efficient method for elastic lateral deformation analysis of cold-formed wall panel structures which can be used for such configurations.
- 7 July 2022
- Published by Periodica Polytechnica Budapest University of Technology and Economics in Periodica Polytechnica Civil Engineering
- Vol. 66 (4) , 1060-1070
Prediction of In-plane Stiffness for the Cold-formed Steel Frame of the Wall Panel Structure
The purpose of this research was to study the lateral deformation behavior of cold-formed steel wall panel structures using experimental tests, finite element analysis and analytical methods to study the lateral stiffness of these structures. The wall panel structures were tested by full-scale experiments the experimental results of which were verified by a 3D-finite element model. The verification results showed a good correlation between the experimental tests and a finite element model. The single-column spring model was proposed for an elastic lateral stiffness analysis of the cold-formed steel wall panel structures that were formed by combinations of a guide cantilever beam and springs connection. The spring constants were defined by using the stiffness of the stub-chord connection and the bending stiffness of the chord. The experiments tests and finite element analysis were used to verify this single-column spring model. The comparison results showed good agreement between the analytical prediction, finite element analysis and experimental data in the case of the primary type of cold-formed wall structure. The proposed procedure was an efficient method for elastic lateral deformation analysis of cold-formed wall panel structures which can be used for such configurations.
- 1 January 2020
- Published by Faculty of Engineering, University of Rijeka in Engineering review
- Vol. 41 (1) , 69-84
Stiffness prediction for bolted moment-connections in cold-formed steel trusses
The purpose of this research was to study the behavior of cold-formed steel cantilever truss structures. A cantilever truss structure and bolt-moment connection were tested and verified by the 3D-finite element model. The verification...
- 1 January 2020
- Published by Faculty of Engineering, University of Rijeka in Engineering review
- Vol. 41 (1) , 69-84
Stiffness prediction for bolted moment-connections in cold-formed steel trusses
The purpose of this research was to study the behavior of cold-formed steel cantilever truss structures. A cantilever truss structure and bolt-moment connection were tested and verified by the 3D-finite element model. The verification...
- Open Access
- 9 August 2017
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 7 (4) , 1826-1832
An Investigation on the Ultimate Strength of Cold-Formed Steel Bolted Connections
This paper presents experimental results and finite element analysis of the cold-formed steel bolted connection under shear loading. Experiments are conducted to study the ultimate behaviors, such as ultimate strength and failure mode of connections. The samples were fabricated into three different groups, single bolted, double bolted and quadruple bolted connection. Material properties were determined by tensile coupon testing. Bearing failure modes were detected in the bolted connection tests. The ultimate capacities were compared with the nominal strengths calculated using the AISI (2012). The comparisons show that the nominal strength parameters predicted by this specification is conservative. The finite element analysis shell elements were used to model the cold-formed steel plate while solid elements were used to model the bolted fastenings for the purpose of studying the structural behavior of bolted connections. Material nonlinearities, contact problem and geometry nonlinearities analysis are carried out in order to predict ultimate strength and failure mode of connections. The results show that the proposed model accurately represents the failure mode and ultimate strength of bolted connection, as determined from experimental investigation. The new factor for type of bearing connection has a good agreement with the tested bearing strength of bolt connection.
- 9 August 2017
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 7 (4) , 1826-1832
Open AccessAn Investigation on the Ultimate Strength of Cold-Formed Steel Bolted Connections
This paper presents experimental results and finite element analysis of the cold-formed steel bolted connection under shear loading. Experiments are conducted to study the ultimate behaviors, such as ultimate strength and failure mode of connections. The samples were fabricated into three different groups, single bolted, double bolted and quadruple bolted connection. Material properties were determined by tensile coupon testing. Bearing failure modes were detected in the bolted connection tests. The ultimate capacities were compared with the nominal strengths calculated using the AISI (2012). The comparisons show that the nominal strength parameters predicted by this specification is conservative. The finite element analysis shell elements were used to model the cold-formed steel plate while solid elements were used to model the bolted fastenings for the purpose of studying the structural behavior of bolted connections. Material nonlinearities, contact problem and geometry nonlinearities analysis are carried out in order to predict ultimate strength and failure mode of connections. The results show that the proposed model accurately represents the failure mode and ultimate strength of bolted connection, as determined from experimental investigation. The new factor for type of bearing connection has a good agreement with the tested bearing strength of bolt connection.
- Open Access
- 1 January 2017
- Published by Wiley in Advances in Civil Engineering
- Vol. 2017, 1-19
An Analytical Method for Determining the Load Distribution of Single-Column Multibolt Connection
The purpose of this research was to investigate the effect of geometric variables on the bolt load distributions of a cold-formed steel bolt connection. The study was conducted using an experimental test, finite element analysis, and an analytical method. The experimental study was performed using single-lap shear testing of a concentrically loaded bolt connection fabricated from G550 cold-formed steel. Finite element analysis with shell elements was used to model the cold-formed steel plate while solid elements were used to model the bolt fastener for the purpose of studying the structural behavior of the bolt connections. Material nonlinearities, contact problems, and a geometric nonlinearity procedure were used to predict the failure behavior of the bolt connections. The analytical method was generated using the spring model. The bolt-plate interaction stiffness was newly proposed which was verified by the experiment and finite element model. It was applied to examine the effect of geometric variables on the single-column multibolt connection. The effects were studied of varying bolt diameter, plate thickness, and the plate thickness ratio () on the bolt load distribution. The results of the parametric study showed that theratio controlled the efficiency of the bolt load distribution more than the other parameters studied.- 1 January 2017
- Published by Wiley in Advances in Civil Engineering
- Vol. 2017, 1-19
Open AccessAn Analytical Method for Determining the Load Distribution of Single-Column Multibolt Connection
The purpose of this research was to investigate the effect of geometric variables on the bolt load distributions of a cold-formed steel bolt connection. The study was conducted using an experimental test, finite element analysis, and an analytical method. The experimental study was performed using single-lap shear testing of a concentrically loaded bolt connection fabricated from G550 cold-formed steel. Finite element analysis with shell elements was used to model the cold-formed steel plate while solid elements were used to model the bolt fastener for the purpose of studying the structural behavior of the bolt connections. Material nonlinearities, contact problems, and a geometric nonlinearity procedure were used to predict the failure behavior of the bolt connections. The analytical method was generated using the spring model. The bolt-plate interaction stiffness was newly proposed which was verified by the experiment and finite element model. It was applied to examine the effect of geometric variables on the single-column multibolt connection. The effects were studied of varying bolt diameter, plate thickness, and the plate thickness ratio () on the bolt load distribution. The results of the parametric study showed that theratio controlled the efficiency of the bolt load distribution more than the other parameters studied.