Hongjian Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Hongjian Li has a total of 107 co-authors. Here are the top co-authors by number of shared publications:
- Haojun Zhang
University of California
16 shared publications Shuji Nakamura
Materials Department, University of California, Santa Barbara, California 93106, United States
15 shared publications- Steven DenBaars
Department of Electrical and Computer Engineering, University of California, Santa Barbara, CA, USA
14 shared publications Panpan Li
Future Display Institute of Xiamen
13 shared publications- Panpan Li
Materials Department, University of California 1 , Santa Barbara, California 93106, USA
11 shared publications James S. Speck
Materials Department, University of California, Santa Barbara, California 93106, United States
10 shared publications
Latest Publications
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (11) , 2231-2234
Highly Thermally Stable Long-Wavelength InGaN Micro-Light-Emitting Diodes for Gigabit Optical Links
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (11) , 2231-2234
Highly Thermally Stable Long-Wavelength InGaN Micro-Light-Emitting Diodes for Gigabit Optical Links
- 26 October 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (22) , 42168
Suppressed spectral shift in InGaN red micro-light-emitting diodes via preserved localized-state recombination
Micro-light-emitting diodes (µLEDs) are promising for next-generation micro-displays, but spectrally stable InGaN red emission remains difficult because high-indium-content quantum wells suffer from severe current-induced blueshift and spectral broadening. Here, we demonstrate 5 × 5 µm 2 InGaN red µLEDs with strongly suppressed spectral drift using an AlN interlayer/low-temperature p-GaN design. Compared with the reference µLEDs, which show a 56 nm blueshift from 4 to 100 A/cm 2 , the engineered devices exhibit blueshifts of only 14 nm from 4 to 100 A/cm 2 and 24 nm up to 600 A/cm 2 , together with a small linewidth variation over the common 4-100 A/cm 2 range. Comparative atom-probe tomography reveals nanoscale In-composition fluctuations in both samples, with distinct local compositional contrast retained in the analyzed upper-QW region of the engineered sample; this local observation is not interpreted as a broader ensemble-scale distribution of radiative transition energies. Temperature- and power-dependent photoluminescence further indicate a localized-state ensemble that is more robust against thermal and carrier-density perturbations. These correlated observations are consistent with weaker redistribution toward higher-energy recombination channels in the engineered sample. The engineered µLEDs reach a peak EQE of 5.9% at 612 nm, providing a route toward spectrally stable InGaN red µLEDs.
- 26 October 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (22) , 42168
Suppressed spectral shift in InGaN red micro-light-emitting diodes via preserved localized-state recombination
Micro-light-emitting diodes (µLEDs) are promising for next-generation micro-displays, but spectrally stable InGaN red emission remains difficult because high-indium-content quantum wells suffer from severe current-induced blueshift and spectral broadening. Here, we demonstrate 5 × 5 µm 2 InGaN red µLEDs with strongly suppressed spectral drift using an AlN interlayer/low-temperature p-GaN design. Compared with the reference µLEDs, which show a 56 nm blueshift from 4 to 100 A/cm 2 , the engineered devices exhibit blueshifts of only 14 nm from 4 to 100 A/cm 2 and 24 nm up to 600 A/cm 2 , together with a small linewidth variation over the common 4-100 A/cm 2 range. Comparative atom-probe tomography reveals nanoscale In-composition fluctuations in both samples, with distinct local compositional contrast retained in the analyzed upper-QW region of the engineered sample; this local observation is not interpreted as a broader ensemble-scale distribution of radiative transition energies. Temperature- and power-dependent photoluminescence further indicate a localized-state ensemble that is more robust against thermal and carrier-density perturbations. These correlated observations are consistent with weaker redistribution toward higher-energy recombination channels in the engineered sample. The engineered µLEDs reach a peak EQE of 5.9% at 612 nm, providing a route toward spectrally stable InGaN red µLEDs.
- 12 October 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (15)
C-plane yellow–green InGaN micro-light-emitting diodes with 1.55 GHz modulation bandwidth for free-space visible-light communication
Yellow–green InGaN micro-light-emitting diodes (micro-LEDs) are attractive transmitters for visible-light communication, yet high-In-content quantum wells usually impose a trade-off among efficiency, optical power, and modulation speed. Here, we report c-plane single-quantum-well InGaN micro-LEDs emitting near 545 nm that combine milliwatt-level output at high-current density with gigahertz-class small-signal modulation. Devices with lateral sizes of 40 and 60 μm exhibit peak external quantum efficiencies (EQEs) of 5.36% and 5.35%, respectively, and retain EQEs of 2.84% and 2.83% at 1000 A cm−2. The 40 μm device reaches a maximum −3dB bandwidth of 1.55 GHz and maintains gigahertz-class bandwidth from a high operation temperature (300–375 K). We also demonstrate 2.0 Gbit/s free-space non-return-to-zero on–off keying transmission with an estimated bit-error rate below the 7% overhead hard-decision forward-error-correction limit. These results show that c-plane yellow–green InGaN micro-LEDs can provide compact, efficient, and thermally robust transmitters for high-speed free-space visible-light links.
- 12 October 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (15)
C-plane yellow–green InGaN micro-light-emitting diodes with 1.55 GHz modulation bandwidth for free-space visible-light communication
Yellow–green InGaN micro-light-emitting diodes (micro-LEDs) are attractive transmitters for visible-light communication, yet high-In-content quantum wells usually impose a trade-off among efficiency, optical power, and modulation speed. Here, we report c-plane single-quantum-well InGaN micro-LEDs emitting near 545 nm that combine milliwatt-level output at high-current density with gigahertz-class small-signal modulation. Devices with lateral sizes of 40 and 60 μm exhibit peak external quantum efficiencies (EQEs) of 5.36% and 5.35%, respectively, and retain EQEs of 2.84% and 2.83% at 1000 A cm−2. The 40 μm device reaches a maximum −3dB bandwidth of 1.55 GHz and maintains gigahertz-class bandwidth from a high operation temperature (300–375 K). We also demonstrate 2.0 Gbit/s free-space non-return-to-zero on–off keying transmission with an estimated bit-error rate below the 7% overhead hard-decision forward-error-correction limit. These results show that c-plane yellow–green InGaN micro-LEDs can provide compact, efficient, and thermally robust transmitters for high-speed free-space visible-light links.
- 31 August 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (9)
An InGaN amber nano-light-emitting diode with external quantum efficiency of 10.1%
Efficient long-wavelength nano-light-emitting diodes (nano-LEDs) are essential for ultrahigh-density monolithic RGB micro-displays, yet their efficiency usually deteriorates as device size shrinks because sidewall-related nonradiative recombination becomes increasingly important. Here, we demonstrate electrically injected planar InGaN amber nano-LEDs with a circular mesa diameter of ∼840 nm fabricated by a conventional top-down process with conformal ALD-Al2O3 sidewall passivation. The device emits at 608 nm and exhibits an ultralow reverse leakage current of ∼10−14 A at −5 V. A peak external quantum efficiency of 10.1% is achieved at ∼12 A/cm2, exceeding that of a 20 μm device from the same wafer (∼9.8% at ∼4 A/cm2). Analysis using an ABC model indicates that downscaling increases the sidewall-related SRH term, but this penalty is overcompensated by enhanced light extraction efficiency in the nanoscale mesa. The fluorescence lifetime imaging microscopy mapping further reveals spatially resolved carrier dynamics that are closely correlated with strong carrier localization in the high-In-content red-emitting quantum wells, which helps suppress sidewall nonradiative recombination. These results establish top-down long-wavelength III-nitride nano-LEDs as a viable route toward ultrahigh-resolution monolithic micro-displays.
- 31 August 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (9)
An InGaN amber nano-light-emitting diode with external quantum efficiency of 10.1%
Efficient long-wavelength nano-light-emitting diodes (nano-LEDs) are essential for ultrahigh-density monolithic RGB micro-displays, yet their efficiency usually deteriorates as device size shrinks because sidewall-related nonradiative recombination becomes increasingly important. Here, we demonstrate electrically injected planar InGaN amber nano-LEDs with a circular mesa diameter of ∼840 nm fabricated by a conventional top-down process with conformal ALD-Al2O3 sidewall passivation. The device emits at 608 nm and exhibits an ultralow reverse leakage current of ∼10−14 A at −5 V. A peak external quantum efficiency of 10.1% is achieved at ∼12 A/cm2, exceeding that of a 20 μm device from the same wafer (∼9.8% at ∼4 A/cm2). Analysis using an ABC model indicates that downscaling increases the sidewall-related SRH term, but this penalty is overcompensated by enhanced light extraction efficiency in the nanoscale mesa. The fluorescence lifetime imaging microscopy mapping further reveals spatially resolved carrier dynamics that are closely correlated with strong carrier localization in the high-In-content red-emitting quantum wells, which helps suppress sidewall nonradiative recombination. These results establish top-down long-wavelength III-nitride nano-LEDs as a viable route toward ultrahigh-resolution monolithic micro-displays.
- 11 May 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (19)
Investigation on compositional pulling effect of InGaN red multiple quantum wells and its remedy
Achieving InGaN quantum wells (QWs) with high indium compositions for red emission presents significant challenges. One challenge is that the red peak is often accompanied by a short-wavelength emission with increased current injection. In this work, such dual-peak emissions in InGaN red multiple QWs (MQWs) were investigated using cross-sectional cathodoluminescence and scanning transmission electron microscopy. This was attributed to the compositional pulling effect. A peak shift from 570 to 600 nm, in conjunction with increased indium composition, was observed across the MQWs from the bottom to the top. By controlling the growth temperature of the individual QWs, short-wavelength emission was suppressed. As a result of this, InGaN red micro light-emitting-diodes (Micro-LEDs) were fabricated, showing a single red emission peak up to a current density of 100 A/cm2 (612 nm) and a peak external quantum efficiency of 7.9% at 5.2 A/cm2. This study not only reveals the presence of the CPE in red InGaN MQWs of high indium compositions but also demonstrates a remedy to achieve single-peak red emission even under high current density operation.
- 11 May 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (19)
Investigation on compositional pulling effect of InGaN red multiple quantum wells and its remedy
Achieving InGaN quantum wells (QWs) with high indium compositions for red emission presents significant challenges. One challenge is that the red peak is often accompanied by a short-wavelength emission with increased current injection. In this work, such dual-peak emissions in InGaN red multiple QWs (MQWs) were investigated using cross-sectional cathodoluminescence and scanning transmission electron microscopy. This was attributed to the compositional pulling effect. A peak shift from 570 to 600 nm, in conjunction with increased indium composition, was observed across the MQWs from the bottom to the top. By controlling the growth temperature of the individual QWs, short-wavelength emission was suppressed. As a result of this, InGaN red micro light-emitting-diodes (Micro-LEDs) were fabricated, showing a single red emission peak up to a current density of 100 A/cm2 (612 nm) and a peak external quantum efficiency of 7.9% at 5.2 A/cm2. This study not only reveals the presence of the CPE in red InGaN MQWs of high indium compositions but also demonstrates a remedy to achieve single-peak red emission even under high current density operation.
- 5 May 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (10) , 17683-17691
High-performance tunnel-junction micro-LEDs grown by MOCVD without post-growth annealing
High-performance tunnel junction (TJ) micro-light-emitting diode (micro LED) devices without post-growth annealing were grown by metalorganic chemical vapor deposition (MOCVD). During the initial growth of the top n − -GaN layer, the device forms island-like structures, allowing hydrogen to escape through the gaps between islands, thereby achieving activation of the p-GaN layer. The device achieves an operating voltage of 2.99 V at 20 A/cm 2 , a peak wall-plug efficiency (WPE) of 45.23%, and exhibits more uniform luminescence intensity in the electroluminescence (EL) image. This work establishes a pathway for enhancing the performance of an MOCVD-grown TJ.
- 5 May 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (10) , 17683-17691
High-performance tunnel-junction micro-LEDs grown by MOCVD without post-growth annealing
High-performance tunnel junction (TJ) micro-light-emitting diode (micro LED) devices without post-growth annealing were grown by metalorganic chemical vapor deposition (MOCVD). During the initial growth of the top n − -GaN layer, the device forms island-like structures, allowing hydrogen to escape through the gaps between islands, thereby achieving activation of the p-GaN layer. The device achieves an operating voltage of 2.99 V at 20 A/cm 2 , a peak wall-plug efficiency (WPE) of 45.23%, and exhibits more uniform luminescence intensity in the electroluminescence (EL) image. This work establishes a pathway for enhancing the performance of an MOCVD-grown TJ.
- 20 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (5) , 949-952
High-Performance Long-Wavelength InGaN Micro-LEDs Achieving 1.01-GHz Bandwidth
The low modulation bandwidth of AlInGaP red micro light-emitting diodes (Micro-LEDs) limits full-color visible light communication (VLC) applications. Here, we demonstrate fast modulation speed long wavelength InGaN Micro-LEDs with red multiple quantum wells (MQWs) that exhibit sharp and uniform interfaces. The red Micro-LEDs show extremely low reverse leakage current of 1.77 × 10-11 A at -5 V and an external quantum efficiency (EQE) of 4.07%. The -3 dB modulation bandwidth reaches 1.01 GHz for 20 μm device, which is the highest one among red Micro-LEDs. The dependence of modulation bandwidth on current densities revealed the transition of carrier lifetime mechanisms with current injection level. Furthermore, an optical communication system was established, achieving open eye diagrams up to 1 Gbps with measured quality factors. These results demonstrate the large potential of long wavelength InGaN Micro-LEDs for next-generation high-speed VLC systems and optical computing.
- 20 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (5) , 949-952
High-Performance Long-Wavelength InGaN Micro-LEDs Achieving 1.01-GHz Bandwidth
The low modulation bandwidth of AlInGaP red micro light-emitting diodes (Micro-LEDs) limits full-color visible light communication (VLC) applications. Here, we demonstrate fast modulation speed long wavelength InGaN Micro-LEDs with red multiple quantum wells (MQWs) that exhibit sharp and uniform interfaces. The red Micro-LEDs show extremely low reverse leakage current of 1.77 × 10-11 A at -5 V and an external quantum efficiency (EQE) of 4.07%. The -3 dB modulation bandwidth reaches 1.01 GHz for 20 μm device, which is the highest one among red Micro-LEDs. The dependence of modulation bandwidth on current densities revealed the transition of carrier lifetime mechanisms with current injection level. Furthermore, an optical communication system was established, achieving open eye diagrams up to 1 Gbps with measured quality factors. These results demonstrate the large potential of long wavelength InGaN Micro-LEDs for next-generation high-speed VLC systems and optical computing.
- 2 September 2025
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 40 (9) , 090201
Special issue on group III-nitrides for next-generation optoelectronic devices
- 2 September 2025
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 40 (9) , 090201
Special issue on group III-nitrides for next-generation optoelectronic devices
- Open Access
- 1 August 2024
- Published by AIP Publishing in APL Materials
- Vol. 12 (8)
Advances in InGaN-based RGB micro-light-emitting diodes for AR applications: Status and perspective
Micro-light-emitting diodes (µLEDs) are gathering significant interest as a technology for emerging micro-displays. However, µLEDs encounter numerous obstacles, including size-dependent efficiency loss, poor efficiency of red µLEDs, and challenges associated with the mass transfer and integration of full-color µLEDs. These issues become more acute in ultra-small µLEDs (<5 µm), which were required by the augmented reality (AR) displays. Here, we discuss the principal challenges faced by µLEDs and explore the possible solutions. We highlight recent advances in InGaN-based RGB µLEDs tailored for AR displays. In particular, we discuss the advancements in ultra-small InGaN µLEDs scaled down to 1 µm, the developments in InGaN red µLEDs, and the implementation of tunnel junction-based cascaded InGaN µLEDs for monolithic integration.
- 1 August 2024
- Published by AIP Publishing in APL Materials
- Vol. 12 (8)
Open AccessAdvances in InGaN-based RGB micro-light-emitting diodes for AR applications: Status and perspective
Micro-light-emitting diodes (µLEDs) are gathering significant interest as a technology for emerging micro-displays. However, µLEDs encounter numerous obstacles, including size-dependent efficiency loss, poor efficiency of red µLEDs, and challenges associated with the mass transfer and integration of full-color µLEDs. These issues become more acute in ultra-small µLEDs (<5 µm), which were required by the augmented reality (AR) displays. Here, we discuss the principal challenges faced by µLEDs and explore the possible solutions. We highlight recent advances in InGaN-based RGB µLEDs tailored for AR displays. In particular, we discuss the advancements in ultra-small InGaN µLEDs scaled down to 1 µm, the developments in InGaN red µLEDs, and the implementation of tunnel junction-based cascaded InGaN µLEDs for monolithic integration.
- 12 May 2023
- Published by American Chemical Society (ACS) in ACS Photonics
- Vol. 10 (6) , 1899-1905
Significant Quantum Efficiency Enhancement of InGaN Red Micro-Light-Emitting Diodes with a Peak External Quantum Efficiency of up to 6%
- 12 May 2023
- Published by American Chemical Society (ACS) in ACS Photonics
- Vol. 10 (6) , 1899-1905
Significant Quantum Efficiency Enhancement of InGaN Red Micro-Light-Emitting Diodes with a Peak External Quantum Efficiency of up to 6%