Maarten K. Sabbe
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Maarten K. Sabbe has a total of 107 co-authors. Here are the top co-authors by number of shared publications:
- Kevin Marcel Van Geem
Laboratory for Chemical Technology, Ghent University, Technologiepark 125, B-9052 Ghent, Belgium
12 shared publications - Yannick Ureel
Laboratory for Chemical Technology, Department of Materials, Textiles and Chemical Engineering, Ghent University, Technologiepark 125, 9052 Gent, Belgium
10 shared publications - Guy B. Marin
Laboratory for Chemical Technology, Ghent University, Technologiepark 121, 9052 Zwijnaarde, Belgium
7 shared publications - Joris W. Thybaut
Laboratory for Chemical Technology (LCT), Ghent University, Technologiepark 125, 9052 Ghent, Belgium
7 shared publications - Marie-Françoise Reyniers
Laboratory for Chemical Technology, Ghent University, Technologiepark 121, 9052 Zwijnaarde, Belgium
7 shared publications - An Verberckmoes
Industrial Catalysis and Adsorption Technology (INCAT), Department of Materials Textiles and Chemical Engineering (MaTCh), Ghent University, Valentin Vaerwyckweg 1, 9000, Ghent, Belgium
6 shared publications
Latest Publications
- 9 May 2026
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 65 (19) , 10205-10213
Importance of Conformer Diversity over Quantity in COSMO-RS-Based LLE Predictions: A Case Study
- 9 May 2026
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 65 (19) , 10205-10213
Importance of Conformer Diversity over Quantity in COSMO-RS-Based LLE Predictions: A Case Study
- 24 February 2026
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry A
- Vol. 130 (10) , 2158-2168
Semi-Empirical Evaluation of Hindered Internal Rotors for Accelerated Thermodynamics Predictions
Accurate determination of a molecule's thermodynamic properties using quantum chemistry methods is crucial for developing kinetic models. A vital step in the quantum chemical workflow is calculating torsional energy profiles to apply the one-dimensional hindered-rotor approximation. However, these profiles are typically obtained by performing rotational scans using density functional theory (DFT) methods, which adds high computational cost to the workflow. Here, we assess the performance of the semiempirical GFN2-xTB method for rapid generation of these torsional profiles by calculating the contributions of GFN2-xTB and B3LYP profiles to the enthalpy, entropy, heat capacity, and Gibbs free energy of molecules. Several correction methods to improve the results are proposed and evaluated. It is found that correcting the energy profiles based on their second derivative at the optimized-geometry point yields the most accurate results. This optimal correction method results in a mean absolute error on the Gibbs free energy at 1000 K of 0.43 kJ mol-1 for a hydrocarbons data set and 0.93 kJ mol-1 for a data set of nitrogen-containing compounds. In conclusion, the GFN2-xTB method, when combined with a suitable correction method, can accelerate the generation of hindered rotor profiles by a factor of 700, with only a minor loss of accuracy.
- 24 February 2026
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry A
- Vol. 130 (10) , 2158-2168
Semi-Empirical Evaluation of Hindered Internal Rotors for Accelerated Thermodynamics Predictions
Accurate determination of a molecule's thermodynamic properties using quantum chemistry methods is crucial for developing kinetic models. A vital step in the quantum chemical workflow is calculating torsional energy profiles to apply the one-dimensional hindered-rotor approximation. However, these profiles are typically obtained by performing rotational scans using density functional theory (DFT) methods, which adds high computational cost to the workflow. Here, we assess the performance of the semiempirical GFN2-xTB method for rapid generation of these torsional profiles by calculating the contributions of GFN2-xTB and B3LYP profiles to the enthalpy, entropy, heat capacity, and Gibbs free energy of molecules. Several correction methods to improve the results are proposed and evaluated. It is found that correcting the energy profiles based on their second derivative at the optimized-geometry point yields the most accurate results. This optimal correction method results in a mean absolute error on the Gibbs free energy at 1000 K of 0.43 kJ mol-1 for a hydrocarbons data set and 0.93 kJ mol-1 for a data set of nitrogen-containing compounds. In conclusion, the GFN2-xTB method, when combined with a suitable correction method, can accelerate the generation of hindered rotor profiles by a factor of 700, with only a minor loss of accuracy.
- 20 November 2025
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 39 (48) , 22780-22796
Characterization and Source Tracing of Nitrogenates and Halogens in Polyolefin Waste Pyrolysis Oils by Ultrahigh-Resolution FT-ICR MS
- 20 November 2025
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 39 (48) , 22780-22796
Characterization and Source Tracing of Nitrogenates and Halogens in Polyolefin Waste Pyrolysis Oils by Ultrahigh-Resolution FT-ICR MS
- 6 November 2025
- Published by Elsevier in Journal of Analytical and Applied Pyrolysis
- Vol. 193
A combined gas and catalytic-phase kinetic model for ex-situ catalytic pyrolysis of polyethylene
- 6 November 2025
- Published by Elsevier in Journal of Analytical and Applied Pyrolysis
- Vol. 193
A combined gas and catalytic-phase kinetic model for ex-situ catalytic pyrolysis of polyethylene
- Open Access
- 19 August 2025
- Published by Elsevier in Engineering
- Vol. 52, 14-18
How Can Active Machine Learning Aid Kinetic Model Generation, and Why Should We Care?
- 19 August 2025
- Published by Elsevier in Engineering
- Vol. 52, 14-18
Open AccessHow Can Active Machine Learning Aid Kinetic Model Generation, and Why Should We Care?
- 12 August 2025
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 64 (34) , 16563-16573
Microkinetic Modeling of Plastic Waste Catalytic Cracking with Phosphorus-Modified Mesoporous HZSM-5: An Iso-Octane Model Compound Study
- 12 August 2025
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 64 (34) , 16563-16573
Microkinetic Modeling of Plastic Waste Catalytic Cracking with Phosphorus-Modified Mesoporous HZSM-5: An Iso-Octane Model Compound Study
- Open Access
- 9 July 2025
- Published by American Chemical Society (ACS) in ACS Engineering Au
- Vol. 5 (4) , 434-449
The Influence of Mesopore Architecture in Hierarchical H-ZSM-5 on n-Butanol Dehydration
Zeolites are among the most widely employed catalysts in the (petro-)chemical industry. However, due to their elaborate microporous network, they are prone to diffusion limitations and deactivation. Several modification methods have been proposed to overcome these limitations, each exhibiting their benefits. In this work, two of the most promising strategies were combined, i.e., limiting the length of one of the crystal axes during synthesis to achieve a platelike morphology and introducing mesoporosity, creating a hierarchical platelike H-ZSM-5. The platelike morphology was obtained by adding urea as a growth modifier to the synthesis mixture, and mesopores were introduced in the platelike H-ZSM-5 through etching with a NaOH/TPAOH mixture. As a benchmark, the same etching procedure was applied to a commercial ZSM-5 counterpart. These materials were tested in the n-butanol dehydration, where the platelike morphology exhibited an improved catalytic performance, significantly increasing the activity per acid site and stability, and slightly increasing the selectivity toward the butenes. The generation of mesopores in commercial ZSM-5 also increased the activity per acid site but reduced the catalyst’s stability, likely due to an increased amount of Lewis acid sites upon etching. When applying the same modification method to the platelike H-ZSM-5, much larger mesopores and some macropores were observed. These further increased the stability of the catalyst but barely affected the activity per acid site, presumably due to the already optimized catalytic performance of the platelike H-ZSM-5.
- 9 July 2025
- Published by American Chemical Society (ACS) in ACS Engineering Au
- Vol. 5 (4) , 434-449
Open AccessThe Influence of Mesopore Architecture in Hierarchical H-ZSM-5 on n-Butanol Dehydration
Zeolites are among the most widely employed catalysts in the (petro-)chemical industry. However, due to their elaborate microporous network, they are prone to diffusion limitations and deactivation. Several modification methods have been proposed to overcome these limitations, each exhibiting their benefits. In this work, two of the most promising strategies were combined, i.e., limiting the length of one of the crystal axes during synthesis to achieve a platelike morphology and introducing mesoporosity, creating a hierarchical platelike H-ZSM-5. The platelike morphology was obtained by adding urea as a growth modifier to the synthesis mixture, and mesopores were introduced in the platelike H-ZSM-5 through etching with a NaOH/TPAOH mixture. As a benchmark, the same etching procedure was applied to a commercial ZSM-5 counterpart. These materials were tested in the n-butanol dehydration, where the platelike morphology exhibited an improved catalytic performance, significantly increasing the activity per acid site and stability, and slightly increasing the selectivity toward the butenes. The generation of mesopores in commercial ZSM-5 also increased the activity per acid site but reduced the catalyst’s stability, likely due to an increased amount of Lewis acid sites upon etching. When applying the same modification method to the platelike H-ZSM-5, much larger mesopores and some macropores were observed. These further increased the stability of the catalyst but barely affected the activity per acid site, presumably due to the already optimized catalytic performance of the platelike H-ZSM-5.
- Open Access
Direct Conversion of 1,3-Butanediol to 1,3-Butadiene over ZSM-22 Catalysts: Influence of the Si/Al Ratio
ZSM-22 zeolites with different Si/Al ratios (38, 50, 80) were prepared via a hydrothermal synthesis method, investigated for the catalytic dehydration of 1,3-butanediol (1,3-BDO) to butadiene (BD) at 300 °C. The catalytic performance of the synthesized materials was related to their properties and compared to a commercial ZSM-22 zeolite (Si/Al = 30). ZSM-22 (50) exhibited a quick decline in conversion, a lower BD selectivity, and higher propylene selectivity compared to the other materials, which could be attributed to the presence of strong Lewis acid sites and silanol nests. The Lewis sites favor the cracking of the intermediate 3-buten-1-ol (3B1OL) into propylene, while the silanol nests interact with the free hydroxyl group of 3B1OL, potentially inhibiting further dehydration towards BD. The highest initial BD yield of 74% was observed over ZSM-22 (80), while the highest initial BD productivity of 2.7 gBD·g−1cata·h−1 was achieved over ZSM-22 (38). After 22 h time on stream (TOS), c-ZSM-22 and ZSM-22 (38) outperformed previously reported catalysts from the literature, with productivities amounting to 1.3 gBD·g−1cata·h−1 and 1.2 gBD·g−1cata·h−1, respectively, at a site time of 6.6 molH+·s·mol−11,3-BDO.
Open AccessDirect Conversion of 1,3-Butanediol to 1,3-Butadiene over ZSM-22 Catalysts: Influence of the Si/Al Ratio
ZSM-22 zeolites with different Si/Al ratios (38, 50, 80) were prepared via a hydrothermal synthesis method, investigated for the catalytic dehydration of 1,3-butanediol (1,3-BDO) to butadiene (BD) at 300 °C. The catalytic performance of the synthesized materials was related to their properties and compared to a commercial ZSM-22 zeolite (Si/Al = 30). ZSM-22 (50) exhibited a quick decline in conversion, a lower BD selectivity, and higher propylene selectivity compared to the other materials, which could be attributed to the presence of strong Lewis acid sites and silanol nests. The Lewis sites favor the cracking of the intermediate 3-buten-1-ol (3B1OL) into propylene, while the silanol nests interact with the free hydroxyl group of 3B1OL, potentially inhibiting further dehydration towards BD. The highest initial BD yield of 74% was observed over ZSM-22 (80), while the highest initial BD productivity of 2.7 gBD·g−1cata·h−1 was achieved over ZSM-22 (38). After 22 h time on stream (TOS), c-ZSM-22 and ZSM-22 (38) outperformed previously reported catalysts from the literature, with productivities amounting to 1.3 gBD·g−1cata·h−1 and 1.2 gBD·g−1cata·h−1, respectively, at a site time of 6.6 molH+·s·mol−11,3-BDO.
- Open Access
- 30 June 2025
- Published by Royal Society of Chemistry (RSC) in Polymer Chemistry
- Vol. 16 (31) , 3496-3510
Pulsed laser polymerization to retrieve kinetic parameters for a propagated mid-chain radical in poly(n-butyl acrylate) synthesis: a combined DFT and kinetic Monte Carlo study
Roadmap to obtain acrylate-specific rate coefficients/Arrhenius parametersrr via PLP-SEC.
- 30 June 2025
- Published by Royal Society of Chemistry (RSC) in Polymer Chemistry
- Vol. 16 (31) , 3496-3510
Open AccessPulsed laser polymerization to retrieve kinetic parameters for a propagated mid-chain radical in poly(n-butyl acrylate) synthesis: a combined DFT and kinetic Monte Carlo study
Roadmap to obtain acrylate-specific rate coefficients/Arrhenius parametersrr via PLP-SEC.
- Open Access
- 20 January 2025
- Published by Elsevier in Chemical Engineering Journal
- Vol. 506
Multiscale analysis of the M1 MoVNbTeO catalyst for ethylene production via selective ethane oxidation: From atomistic calculations to the industrial reactor
- 20 January 2025
- Published by Elsevier in Chemical Engineering Journal
- Vol. 506
Open AccessMultiscale analysis of the M1 MoVNbTeO catalyst for ethylene production via selective ethane oxidation: From atomistic calculations to the industrial reactor