Bhargav Pandya
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Bhargav Pandya has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Nishant Modi
School of Technology, Pandit Deendayal Petroleum University, Gandhinagar, Gujarat 382007, India
9 shared publications - Vinay Kumar
Gujarat Power Engineering and Research Institute
8 shared publications Jatin Patel
Pandit Deendayal Petroleum University
7 shared publicationsVijay Matawala
Gujarat Power Engineering and Research Institute
4 shared publications- Anurag Mudgal
Mechanical Engineering Department, School of Technology, Pandit Deendayal Energy University, Gandhinagar, India
3 shared publications - Jatin Patel
Mechanical Engineering Department, School of Technology, Pandit Deendayal Energy University, Gandhinagar, India
3 shared publications
Latest Publications
- Open Access
- 1 April 2022
- Published by KEAI Publishing in Energy and Built Environment
- Vol. 3 (2) , 181-189
Integration of evacuated solar collectors with an adsorptive ice maker for hot climate region
- 1 April 2022
- Published by KEAI Publishing in Energy and Built Environment
- Vol. 3 (2) , 181-189
Open AccessIntegration of evacuated solar collectors with an adsorptive ice maker for hot climate region
- 2 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Synergetic Control of Three-Phase AC-AC Current-Source Converter Employing Monolithic Bidirectional 600 V GaN Transistors
AC-AC current-source converters (CSCs) are an interesting alternative to the widely-used voltage-source converters for next-generation motor drive applications, as they inherently feature continuous output voltages and minimum filter effort. This mitigates issues such as reflections on long motor cables, high-frequency motor losses, the need for expensive shielded motor cables, and common-mode currents that damage motor bearings. In this paper, we first propose a new synergetic control for an AC-AC CSC that always operates either the front-end rectifier or the output-side inverter stage with one phase clamped, reducing switching losses compared to conventional modulation that continuously operates all three phases. We then provide calorimetric switching loss measurements of a novel 600 V, 140 mW monolithic bidirectional GaN transistor, and model the impact of the third, passive switch present in CSC commutation cells on switching losses. This facilitates a subsequent quantitative performance evaluation of an exemplary AC-AC CSC motor drive that employs the GaN M-BDS and operates from a 200 V three-phase mains. For a nominal motor power of 1.5 kW and a required AC-AC semiconductor efficiency of 98 %, a conventionally controlled CSC can operate with a switching frequency of 48 kHz, whereas the proposed synergetic control enables twice the switching frequency, i.e., 96 kHz and accordingly facilitates a significant volume reduction of the DC-link inductor and the input and output side filter capacitors.
- 2 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Synergetic Control of Three-Phase AC-AC Current-Source Converter Employing Monolithic Bidirectional 600 V GaN Transistors
AC-AC current-source converters (CSCs) are an interesting alternative to the widely-used voltage-source converters for next-generation motor drive applications, as they inherently feature continuous output voltages and minimum filter effort. This mitigates issues such as reflections on long motor cables, high-frequency motor losses, the need for expensive shielded motor cables, and common-mode currents that damage motor bearings. In this paper, we first propose a new synergetic control for an AC-AC CSC that always operates either the front-end rectifier or the output-side inverter stage with one phase clamped, reducing switching losses compared to conventional modulation that continuously operates all three phases. We then provide calorimetric switching loss measurements of a novel 600 V, 140 mW monolithic bidirectional GaN transistor, and model the impact of the third, passive switch present in CSC commutation cells on switching losses. This facilitates a subsequent quantitative performance evaluation of an exemplary AC-AC CSC motor drive that employs the GaN M-BDS and operates from a 200 V three-phase mains. For a nominal motor power of 1.5 kW and a required AC-AC semiconductor efficiency of 98 %, a conventionally controlled CSC can operate with a switching frequency of 48 kHz, whereas the proposed synergetic control enables twice the switching frequency, i.e., 96 kHz and accordingly facilitates a significant volume reduction of the DC-link inductor and the input and output side filter capacitors.
- 26 May 2020
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 142 (10) , 1-21
Investigation of an Energy Source Temperature for NH3 + NaSCN and NH3 + LiNO3 Absorption Refrigeration Systems
This paper evaluates the energy source temperature for novel salts based ammonia/sodium thiocyanate (NH3 + NaSCN) and ammonia/lithium nitrate (NH3 + LiNO3) absorption refrigeration systems. Minimum energy source temperature (cutoff) required to initiate the cooling, critical energy source temperature for optimized thermodynamic performance and possible maximum energy source temperature to avoid crystallization have been determined, and empirical correlations are developed to facilitate continuous operation of the system. A comparison of cutoff energy source temperature depicts that the NH3 + NaSCN pair requires averagely 6 –7 °C higher cutoff temperature compared with the NH3 + LiNO3 pair. Contradictory to this, the maximum coefficient of performance (COP) of the NH3 + NaSCN pair is 7.02% higher than that the NH3 + LiNO3 pair. However, NH3 + NaSCN pair operates in a very narrow range of energy source temperature. From the P − T − X diagram, the crystallization phenomenon is clarified and the maximum energy source temperature has been determined beyond which the system would not function due to crystallization problems. For −10 °C evaporator temperature, the energy source temperature should be controlled between 87 °C and 115 °C for the NH3 + NaSCN pair and between 80 °C and 147 °C for the NH3 + LiNO3 pair.
- 26 May 2020
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 142 (10) , 1-21
Investigation of an Energy Source Temperature for NH3 + NaSCN and NH3 + LiNO3 Absorption Refrigeration Systems
This paper evaluates the energy source temperature for novel salts based ammonia/sodium thiocyanate (NH3 + NaSCN) and ammonia/lithium nitrate (NH3 + LiNO3) absorption refrigeration systems. Minimum energy source temperature (cutoff) required to initiate the cooling, critical energy source temperature for optimized thermodynamic performance and possible maximum energy source temperature to avoid crystallization have been determined, and empirical correlations are developed to facilitate continuous operation of the system. A comparison of cutoff energy source temperature depicts that the NH3 + NaSCN pair requires averagely 6 –7 °C higher cutoff temperature compared with the NH3 + LiNO3 pair. Contradictory to this, the maximum coefficient of performance (COP) of the NH3 + NaSCN pair is 7.02% higher than that the NH3 + LiNO3 pair. However, NH3 + NaSCN pair operates in a very narrow range of energy source temperature. From the P − T − X diagram, the crystallization phenomenon is clarified and the maximum energy source temperature has been determined beyond which the system would not function due to crystallization problems. For −10 °C evaporator temperature, the energy source temperature should be controlled between 87 °C and 115 °C for the NH3 + NaSCN pair and between 80 °C and 147 °C for the NH3 + LiNO3 pair.
- 26 March 2020
- Published by ASME International in Journal of Solar Energy Engineering
- Vol. 142 (5) , 1-34
Dynamic Performance Investigation of Single-Effect NH3 + LiNO3 and NH3 + NaSCN Solar Cooling Cycles: A Case Study for Western Indian Climate
This article compares the dynamic behaviour of solar assisted novel salts-based ammonia/sodium thiocyanate (NH3+NaSCN) and ammonia/lithium nitrate (NH3+LiNO3) single effect absorption refrigeration cycles. An evacuated tube collector (ETC) is attached with fully mixed hot water storage tank to power the absorption system. Variations in ambient conditions are determined for Gujarat Region of India and their effects on absorption cycles critical parameters are quantified throughout the days for the months of April to September. Respectively, systems performance is investigated and compared on terms of Coefficient of performance (COP), Refrigeration Capacity, Efficiency and Solar COP (SCOP). At same operating conditions, it is found that the NH3+LiNO3 cycle can achieve much lower evaporator temperature (−13.1°C) then NH3+NaSCN cycle (−7.5 °C), maximum possible COP for NH3+NaSCN cycle is 0.73 and 0.68 for NH3+LiNO3 cycle. Working limit of NH3+LiNO3 cycle is wide-ranging and narrow for NH3+NaSCN cycle due to high crystallization possibility. SCOP varies from 0.18 to 0.43 for NH3+NaSCN cycle and 0.17 to 0.39 for NH3+LiNO3 cycle over the period of six months. Based on these findings, the suitable working cycle is justified.
- 26 March 2020
- Published by ASME International in Journal of Solar Energy Engineering
- Vol. 142 (5) , 1-34
Dynamic Performance Investigation of Single-Effect NH3 + LiNO3 and NH3 + NaSCN Solar Cooling Cycles: A Case Study for Western Indian Climate
This article compares the dynamic behaviour of solar assisted novel salts-based ammonia/sodium thiocyanate (NH3+NaSCN) and ammonia/lithium nitrate (NH3+LiNO3) single effect absorption refrigeration cycles. An evacuated tube collector (ETC) is attached with fully mixed hot water storage tank to power the absorption system. Variations in ambient conditions are determined for Gujarat Region of India and their effects on absorption cycles critical parameters are quantified throughout the days for the months of April to September. Respectively, systems performance is investigated and compared on terms of Coefficient of performance (COP), Refrigeration Capacity, Efficiency and Solar COP (SCOP). At same operating conditions, it is found that the NH3+LiNO3 cycle can achieve much lower evaporator temperature (−13.1°C) then NH3+NaSCN cycle (−7.5 °C), maximum possible COP for NH3+NaSCN cycle is 0.73 and 0.68 for NH3+LiNO3 cycle. Working limit of NH3+LiNO3 cycle is wide-ranging and narrow for NH3+NaSCN cycle due to high crystallization possibility. SCOP varies from 0.18 to 0.43 for NH3+NaSCN cycle and 0.17 to 0.39 for NH3+LiNO3 cycle over the period of six months. Based on these findings, the suitable working cycle is justified.
- 4 September 2019
- Published by Springer Nature
- p. 77-86
Thermo-economic Comparison of Solar Heat Driven NH3–LiNO3 and NH3–H2O Absorption Refrigeration System
- 4 September 2019
- Published by Springer Nature
- p. 77-86
Thermo-economic Comparison of Solar Heat Driven NH3–LiNO3 and NH3–H2O Absorption Refrigeration System
- 21 May 2019
- Published by Springer Nature in Building Simulation
- Vol. 12 (6) , 1063-1075
Thermodynamic performance and comparison of solar assisted double effect absorption cooling system with LiCl-H2O and LiBr-H2O working fluid
- 21 May 2019
- Published by Springer Nature in Building Simulation
- Vol. 12 (6) , 1063-1075
Thermodynamic performance and comparison of solar assisted double effect absorption cooling system with LiCl-H2O and LiBr-H2O working fluid
- 4 April 2019
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 141 (9) , 1-41
Advanced Exergetic Assessment of a Vapor Compression Cycle With Alternative Refrigerants
The present study compares the thermal performance of various alternative refrigerants with conventional refrigerant operating on a vapor compression cycle with energetic, exergetic, and advanced exergetic approaches. Appropriate alternative refrigerants are selected for the analysis, and R1234yf is recommended as the best suitable refrigerant to replace the existing refrigerants. By splitting the exergy destruction into endogenous and unavoidable, endogenous and avoidable, exogenous and unavoidable, and exogenous and avoidable parts, an advanced exergy method depicts the real potentials for the improvement in the thermal system. Moreover, a traditional exergy method prefers condenser for performance improvement as it has 18.48% higher exergy destruction than evaporator, whereas the advanced exergy method proposes evaporator rather than condenser since its endogenous and avoidable destruction part is 26.38% more than condenser for R1234yf refrigerant.
- 4 April 2019
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 141 (9) , 1-41
Advanced Exergetic Assessment of a Vapor Compression Cycle With Alternative Refrigerants
The present study compares the thermal performance of various alternative refrigerants with conventional refrigerant operating on a vapor compression cycle with energetic, exergetic, and advanced exergetic approaches. Appropriate alternative refrigerants are selected for the analysis, and R1234yf is recommended as the best suitable refrigerant to replace the existing refrigerants. By splitting the exergy destruction into endogenous and unavoidable, endogenous and avoidable, exogenous and unavoidable, and exogenous and avoidable parts, an advanced exergy method depicts the real potentials for the improvement in the thermal system. Moreover, a traditional exergy method prefers condenser for performance improvement as it has 18.48% higher exergy destruction than evaporator, whereas the advanced exergy method proposes evaporator rather than condenser since its endogenous and avoidable destruction part is 26.38% more than condenser for R1234yf refrigerant.