Bankim Mahanta
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Bankim Mahanta has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Pathegama Gamage Ranjith
Monash University Building 60
7 shared publications T.N. Singh
7 shared publicationsVikram Vishal
Computational and Experimental Geomechanics Laboratory, Department of Earth Sciences
6 shared publicationsT. N. Singh
Indian Institute of Technology Bombay
4 shared publications- Prakash Kumar Singh
Department of Earth and Planetary Sciences, University of Allahabad, Prayagraj, India
3 shared publications A. Tripathy
2 shared publications
Latest Publications
- 1 December 2024
- Published by Springer Nature
- p. 327-342
Evaluation of Brittleness Index of Different Shale Lithotypes from Rajmahal Basin, India
- 1 December 2024
- Published by Springer Nature
- p. 327-342
Evaluation of Brittleness Index of Different Shale Lithotypes from Rajmahal Basin, India
- 15 May 2019
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 33 (6) , 4835-4848
Interpreting Pore Dimensions in Gas Shales Using a Combination of SEM Imaging, Small-Angle Neutron Scattering, and Low-Pressure Gas Adsorption
- 15 May 2019
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 33 (6) , 4835-4848
Interpreting Pore Dimensions in Gas Shales Using a Combination of SEM Imaging, Small-Angle Neutron Scattering, and Low-Pressure Gas Adsorption
- 19 December 2018
- Published by Taylor & Francis
- p. 299-307
Digital rock physics and application of high-resolution micro-CT techniques for geomaterials
Understanding the behaviour of rocks at microstructural levels is important for interpreting their macroscopic behaviour and the long-term successful implementation of their engineering applications like underground coal gasification, geothermal energy extractions, enhanced oil recovery, geological carbon sequestrations etc. Digital Rock Physics (DRP) is an alternative way for optimization and measurement of various image-based rock properties like porosity, permeability, electrical conductivity and elastic modulus and has been useful due to its high-resolution insight into the complex rock structure. DRP using micro-CT techniques includes image acquisition, image processing followed by the numerical experiments by means of the field equations and their solutions. The foremost microscopic attributes of rocks are pore volume, pore radius; pore coordination number, throat radius and throat channel length and these can be quantified precisely with the application of micro-CT technique. Additionally, pore-network model and flow behaviour simulation can also be achieved using this technique. In the current study, the advancement and usefulness of micro-CT techniques for geomaterials like rocks is discussed and summarised. Further, the technique is applied to an Indian sandstone to evaluate the above-mentioned rock properties.
- 19 December 2018
- Published by Taylor & Francis
- p. 299-307
Digital rock physics and application of high-resolution micro-CT techniques for geomaterials
Understanding the behaviour of rocks at microstructural levels is important for interpreting their macroscopic behaviour and the long-term successful implementation of their engineering applications like underground coal gasification, geothermal energy extractions, enhanced oil recovery, geological carbon sequestrations etc. Digital Rock Physics (DRP) is an alternative way for optimization and measurement of various image-based rock properties like porosity, permeability, electrical conductivity and elastic modulus and has been useful due to its high-resolution insight into the complex rock structure. DRP using micro-CT techniques includes image acquisition, image processing followed by the numerical experiments by means of the field equations and their solutions. The foremost microscopic attributes of rocks are pore volume, pore radius; pore coordination number, throat radius and throat channel length and these can be quantified precisely with the application of micro-CT technique. Additionally, pore-network model and flow behaviour simulation can also be achieved using this technique. In the current study, the advancement and usefulness of micro-CT techniques for geomaterials like rocks is discussed and summarised. Further, the technique is applied to an Indian sandstone to evaluate the above-mentioned rock properties.
- 1 October 2018
- Published by Elsevier in Journal of Natural Gas Science and Engineering
- Vol. 58, 178-188
Experimental investigation of the influence of strain rate on strength; failure attributes and mechanism of Jhiri shale
- 1 October 2018
- Published by Elsevier in Journal of Natural Gas Science and Engineering
- Vol. 58, 178-188
Experimental investigation of the influence of strain rate on strength; failure attributes and mechanism of Jhiri shale
- Open Access
- 11 October 2017
- Published by The Royal Society in Royal Society Open Science
- Vol. 4 (10) , 170896
Assessment of dynamic material properties of intact rocks using seismic wave attenuation: an experimental study
The mechanical properties of any substance are essential facts to understand its behaviour and make the maximum use of the particular substance. Rocks are indeed an important substance, as they are of significant use in the energy industry, specifically for fossil fuels and geothermal energy. Attenuation of seismic waves is a non-destructive technique to investigate mechanical properties of reservoir rocks under different conditions. The attenuation characteristics of five different rock types, siltstone, shale, Australian sandstone, Indian sandstone and granite, were investigated in the laboratory using ultrasonic and acoustic emission instruments in a frequency range of 0.1–1 MHz. The pulse transmission technique and spectral ratios were used to calculate the attenuation coefficient (α) and quality factor (Q) values for the five selected rock types for both primary (P) and secondary (S) waves, relative to the reference steel sample. For all the rock types, the attenuation coefficient was linearly proportional to the frequency of both thePandSwaves. Interestingly, the attenuation coefficient of granite is more than 22% higher than that of siltstone, sandstone and shale for bothPandSwaves. ThePandSwave velocities were calculated based on their recorded travel time, and these velocities were then used to calculate the dynamic mechanical properties including elastic modulus (E), bulk modulus (K), shear modulus (µ) and Poisson's ratio (ν). ThePandSwave velocities for the selected rock types varied in the ranges of 2.43–4.61 km s−1and 1.43–2.41 km h−1, respectively. Furthermore, it was observed that thePwave velocity was always greater than theSwave velocity, and this confirmed the first arrival ofPwaves to the sensor. According to the experimental results, the dynamicEvalue is generally higher than the staticEvalue obtained by unconfined compressive strength tests.
- 11 October 2017
- Published by The Royal Society in Royal Society Open Science
- Vol. 4 (10) , 170896
Open AccessAssessment of dynamic material properties of intact rocks using seismic wave attenuation: an experimental study
The mechanical properties of any substance are essential facts to understand its behaviour and make the maximum use of the particular substance. Rocks are indeed an important substance, as they are of significant use in the energy industry, specifically for fossil fuels and geothermal energy. Attenuation of seismic waves is a non-destructive technique to investigate mechanical properties of reservoir rocks under different conditions. The attenuation characteristics of five different rock types, siltstone, shale, Australian sandstone, Indian sandstone and granite, were investigated in the laboratory using ultrasonic and acoustic emission instruments in a frequency range of 0.1–1 MHz. The pulse transmission technique and spectral ratios were used to calculate the attenuation coefficient (α) and quality factor (Q) values for the five selected rock types for both primary (P) and secondary (S) waves, relative to the reference steel sample. For all the rock types, the attenuation coefficient was linearly proportional to the frequency of both thePandSwaves. Interestingly, the attenuation coefficient of granite is more than 22% higher than that of siltstone, sandstone and shale for bothPandSwaves. ThePandSwave velocities were calculated based on their recorded travel time, and these velocities were then used to calculate the dynamic mechanical properties including elastic modulus (E), bulk modulus (K), shear modulus (µ) and Poisson's ratio (ν). ThePandSwave velocities for the selected rock types varied in the ranges of 2.43–4.61 km s−1and 1.43–2.41 km h−1, respectively. Furthermore, it was observed that thePwave velocity was always greater than theSwave velocity, and this confirmed the first arrival ofPwaves to the sensor. According to the experimental results, the dynamicEvalue is generally higher than the staticEvalue obtained by unconfined compressive strength tests.
- 8 September 2017
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 78 (2) , 883-897
Effects of thermal treatment on physico-morphological properties of Indian fine-grained sandstone
- 8 September 2017
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 78 (2) , 883-897
Effects of thermal treatment on physico-morphological properties of Indian fine-grained sandstone
- 24 August 2017
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 51 (1) , 5-21
The Effect of Lineation on Anisotropy in Dry and Saturated Himalayan Schistose Rock Under Brazilian Test Conditions
- 24 August 2017
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 51 (1) , 5-21
The Effect of Lineation on Anisotropy in Dry and Saturated Himalayan Schistose Rock Under Brazilian Test Conditions