Ana Silva-Magalhães
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ana Silva-Magalhães has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Daniel F. O. Braga
INEGI, Faculdade de Engenharia, Universidade do Porto, Rua Dr. Roberto Frias, 400, 4200-465 Porto, Portugal
4 shared publications - Jeroen De Backer
Friction Welding and Processing Section, TWI Ltd., Cambridge CB21 6AL, UK
4 shared publications - Pedro Miguel Guimarães Pires Moreira
Faculdade de Engenharia, Universidade do Porto, 4200-465 Porto, Portugal
4 shared publications - Miguel A. V. de Figueiredo
FEUP— Faculty of Engineering, University of Porto, 4150-564 Porto, Portugal
3 shared publications A. Grimm
1 shared publicationB. Brenner
1 shared publication
Latest Publications
- 1 October 2019
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 46, 177-184
A Friction Stir Welding case study using Temperature Controlled Robotics with a HPDC Cylinder Block and dissimilar materials joining
- 1 October 2019
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 46, 177-184
A Friction Stir Welding case study using Temperature Controlled Robotics with a HPDC Cylinder Block and dissimilar materials joining
- 1 March 2019
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 39, 12-17
In-situ temperature measurement in friction stir welding of thick section aluminium alloys
- 1 March 2019
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 39, 12-17
In-situ temperature measurement in friction stir welding of thick section aluminium alloys
- Open Access
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Soldagem & Inspeção
- Vol. 24
Thermal Dissipation Effect on Temperature-controlled Friction Stir Welding
During Friction Stir Welding (FSW) of complex geometries, the thermal dissipation, induced by geometric features or the surrounding environment, may strongly affect the final weld quality. In order to guarantee a consistent weld quality for different conditions, in-process welding parameter adaptation is needed. This paper studies the effect of thermal dissipation, induced by the backing bar thermal conductivity, on the weld temperature and the temperature controller response to it. A new temperature sensor solution, the Tool-Workpiece Thermocouple (TWT) method, was applied to acquire online temperature measurements during welding. An FSW-robot equipped with temperature control, achieved by rotation speed adaptation, was used. AA7075-T6 lap joints were performed with and without temperature control. The cooling rate during welding was register plus macrographs and tensile tests were assessed. The controller demonstrated a fast response promoting the heat input necessary to maintain the set welding temperature. The results demonstrated that temperature control using the TWT method is suitable to achieve higher joint performance and provides a fast setup of optimal parameters for different environments.
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Soldagem & Inspeção
- Vol. 24
Open AccessThermal Dissipation Effect on Temperature-controlled Friction Stir Welding
During Friction Stir Welding (FSW) of complex geometries, the thermal dissipation, induced by geometric features or the surrounding environment, may strongly affect the final weld quality. In order to guarantee a consistent weld quality for different conditions, in-process welding parameter adaptation is needed. This paper studies the effect of thermal dissipation, induced by the backing bar thermal conductivity, on the weld temperature and the temperature controller response to it. A new temperature sensor solution, the Tool-Workpiece Thermocouple (TWT) method, was applied to acquire online temperature measurements during welding. An FSW-robot equipped with temperature control, achieved by rotation speed adaptation, was used. AA7075-T6 lap joints were performed with and without temperature control. The cooling rate during welding was register plus macrographs and tensile tests were assessed. The controller demonstrated a fast response promoting the heat input necessary to maintain the set welding temperature. The results demonstrated that temperature control using the TWT method is suitable to achieve higher joint performance and provides a fast setup of optimal parameters for different environments.
- Open Access
- 9 June 2016
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 88 (9-12) , 2899-2908
Temperature measurements during friction stir welding
- 9 June 2016
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 88 (9-12) , 2899-2908
Open AccessTemperature measurements during friction stir welding
- 18 February 2015
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 79 (5-8) , 805-814
Ultimate tensile strength optimization of different FSW aluminium alloy joints
- 18 February 2015
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 79 (5-8) , 805-814
Ultimate tensile strength optimization of different FSW aluminium alloy joints
- Open Access
- 1 January 2015
- Published by Elsevier in Materials Today: Proceedings
- Vol. 2, S169-S178
Friction Stir welding of Light Metals for Industrial Applications
- 1 January 2015
- Published by Elsevier in Materials Today: Proceedings
- Vol. 2, S169-S178
Open AccessFriction Stir welding of Light Metals for Industrial Applications
- 5 November 2014
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 45 (11) , 1010-1017
Friction stir welded butt joints optimization
- 5 November 2014
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 45 (11) , 1010-1017
Friction stir welded butt joints optimization
- 1 March 2014
- Published by Elsevier in Materials & Design (1980-2015)
- Vol. 55, 120-127
Friction stir welded T-joints optimization
- 1 March 2014
- Published by Elsevier in Materials & Design (1980-2015)
- Vol. 55, 120-127
Friction stir welded T-joints optimization