KGKumarukuttan Gopakumar

Kumarukuttan Gopakumar

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Kumarukuttan Gopakumar has a total of 100 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Switched Capacitive Nine-Level Inverter for Drives With Sinusoidal PWM Control in Extended Linear Modulation Range Independent of Load Power Factor

    by Vaidika T. Pardhi, Vibhore Jain, K. Gopakumar, Loganathan Umanand, Dariusz Zielinski

    The proposed work introduces a novel hybrid inverter topology that integrates a flying capacitor with an open-ended induction motor (OEIM) load, using a cascaded H-bridge and a switched capacitor on the other side of the winding. The primary objective of this work is to extend the modulation range using sinusoidal PWM, unlike the traditional six-step method that creates more harmonics. This approach works well even at unity power factor and does not depend on the type of load. The proposed design reduces the semiconductor rating, thus decreasing stress on the components and minimizing switching losses, especially in high-power inverters. By linearizing the over-modulation region with sinusoidal PWM, the system enhances performance during flux weakening, where traditional six-step inverters produce lower-order harmonics. This topology achieves a maximum peak phase fundamental voltage of 0.637 times the DC-link voltage, while extending the linear modulation range using sinusoidal PWM control. Capacitors are kept balanced under all dynamic conditions through space vector redundancy, ensuring proper voltage regulation in the output phase voltages. The functionality of the topology is validated through experimental testing under both steady-state and transient conditions.


  • Open Access

    Sensorless Compensation of DC-Link Current Pulsations in Energy Storage Systems

    by Dariusz Zieliński, Maciej Rudawski, K. Gopakumar

    This study addresses the problem of DC-link current pulsations in four-wire AC/DC converters with energy storage operating under unbalanced load conditions. A sensorless compensation algorithm based on AC-side voltage and current measurements is proposed, eliminating the need for additional sensors. The algorithm incorporates a Second Order Generalized Integrator (SOGI) filter for accurate detection and compensation of the pulsating component. Experimental validation under severe asymmetry confirmed the method’s effectiveness. In case 1, the AC component of the DC-link current was reduced from 7 A to 1.4 A and, in case 2, from 3 A to 0.5 A. Corresponding FFT analysis showed a reduction in relative amplitude from 240% to 21.5% and from 264% to 22%, respectively. In an asymmetrical charging scenario (case 3), the AC component was reduced from 2.5 A to nearly 0 A, corresponding to a decrease from 42% to 4.9% in the FFT spectrum. These results demonstrate that the proposed method enables stable converter operation even under deep phase current imbalances, significantly improving energy storage reliability and utility grid performance.

  • Modulating and Level-Shifted Carrier-Based DSV-PWM Technique With Fifth and Seventh Order Harmonic Elimination for Multilevel Split-Phase OEIM Drive

    by Nair Syam Sundar S., Vivek R. S., Vibhore Jain, K. Gopakumar, L. Umanand, Dariusz Zielinski

    This article proposes a carrier-based multilevel dodecagonal space vector pulse width modulation (DSV-PWM) technique for a split-phase open-end induction motor (OEIM) drive comprising three-level neutral point clamped (NPC) inverters. The phase voltages of the split-phase OEIM drive cancel the fifth and seventh order harmonic components produced from the inverters connected at both ends of the split-phase OEIM using the DSV-PWM technique. This article discusses the generation of modulating signals with minimal trigonometric operations and compares them to the level-shifted triangular carrier signals to produce DSV-PWM signals for the three-level NPC inverters with dc link voltage of VDC, connected to one end of the OEIM. The generation of DSV-PWM signals for the three-level NPC inverters with dc voltage of 0.366VDC, connected to the other end of the split-phase OEIM, is achieved from the logical operation of DSV-PWM signals of opposite end three-level NPC inverters with dc link voltage of VDC. The approach of minimizing the trigonometric operations while generating the modulating signals and adopting the logical method of generating the DSVPWM signals reduces the overall processing time and is 4.64 times faster than the conventional method of producing the DSV-PWM signals through sector identification, vector timing computations, and storing the timing values. This is experimentally verified, and a detailed analysis is presented in this article.


  • A Single DC Source Multilevel Inverter for Drives With Increasing Linear Modulation Range and Fault Tolerant Capability

    by Vaidika T. Pardhi, Rohith Pottekkat, Vivek R. S., K. Gopakumar, Loganathan Umanand, Dariusz Zielinski

    The proposed seven-level hybrid multilevel inverter integrates a three-level flying capacitor with a cascaded H-bridge inverter. The main goal is to develop a seven-level topology that operates efficiently in both linear and extended linear modulation ranges using sinusoidal control. This design expands the linear modulation range with sinusoidal pulse width modulation (PWM) while preserving the multilevel structure. By linearizing the over-modulation region with sinusoidal PWM, the system improves performance during flux weakening, where conventional six-step inverters generate lower-order harmonics. In this topology, the maximum phase peak fundamental remains 0.637 times the dc-link voltage, even in the extended linear modulation range. The inverter is fault-tolerant, ensuring the motor drive continues to operate smoothly and without interruption if an H-bridge switch fails, with the flying capacitor inverter still providing sinusoidal currents. The proposed design uses a single dc source, a reduced switch count, and low-rated voltage semiconductor switches, making it more efficient than other seven-level topologies. It is particularly well-suited for electric vehicles and general ac motor drives. Capacitors remain balanced under all dynamic conditions through space vector redundancies, maintaining proper voltage levels in the output phase voltages. The effectiveness of the proposed method has been experimentally validated in both steady and transient states.


  • Modulating and Carrier-Based Dodecagonal Space Vector Pulse Width Modulation Technique With Fifth and Seventh Order Harmonic Elimination for Split-Phase OEIM

    by Syam Sundar Nair, Prashant Surana, Rohith Pottekkat, Vivek R.S, K. Gopakumar, L. Umanand

    This article proposes a modulating and carrier-based dodecagonal space vector pulse width modulation (DSV-PWM) technique for split-phase open-end induction motor (OEIM). The advantage of the DSV-PWM technique is that the fifth and seventh order (6n±1; n=1,3,5,...) harmonics are eliminated from the phase voltage of the split-phase OEIM. The modulating waveform is generated from the sinusoidal reference signals by adding the triplen, and fifth and seventh order harmonics. This modified reference waveform is compared to the triangular carrier waveform to generate the PWM gating signals for inverter-1 so that the vector addition from two inverters results in a 12-sided polygonal space vector structure for the PWM control. The PWM signals for the two-level inverter-2 connected to the other end of the OEIM are produced by performing a small logical operation using the PWM signals of inverter-1. The dc voltage relation between inverter-1 and inverter-2 is 1:0.366. The timing duration for inverter-1 and inverter-2 is the same to generate the dodecagonal space vector structure (DSVS) and can be easily implemented as in the case of a conventional sine-triangle PWM technique in a three-phase drive. So, mapping the space vectors of the DSVS of conventional split-phase to that of the OEIM drive is simple. This can be achieved using a logical operator like xor . Thus, the computation burden of the digital signal processors to produce the DSV-PWM signals is reduced with the proposed algorithm which is 3.45 times than the conventional space vector-based implementation using sector identification, vector time computation, and storing the switching vectors. A detailed analysis of the modulating waveform and DSV-PWM signal generation with the experimental verification of the proposed drive is presented in this article.


  • Extending the Linear Modulation Range of a Five-Level Inverter Up To the Full Base Speed for Variable Speed Drive Applications

    by Anchal Singh Thakur, Vivek R. S, K. Gopakumar, Umanand Loganathan, B. Subba Reddy B, Dariusz Zielinski

    In this work, a hybrid 5-level inverter topology with a single DC source is proposed along with a method to increase the linear modulation range of this topology up to full base speed with the elimination of lower-order harmonics for variable speed drive applications. The 5-level inverter topology consists of the cascade arrangement of two basic inverter topologies. The 3-level flying capacitor stage with a nominal capacitor voltage of $V_{dc}/2$ is followed by the 3-level H-bridge stage with a nominal capacitor voltage of $V_{dc}/8$ . Using the proposed method, the peak phase fundamental voltage can be increased from 0.577 $V_{dc}$ to 0.637 $V_{dc}$ in the extended linear modulation region for the same DC input. Unlike conventional speed drives, where lower-order harmonics are produced during operation in the extended modulation region (six-step mode), in the proposed topology, lower-order harmonics are eliminated during operation in the extended linear modulation region. This ensures better performance of the variable speed drives up to the full base speed. Experimental results to demonstrate both the steady-state and transient-state performance of the proposed topology are presented in this paper.


  • Flux-Rate-Controlled Adjustable Inductor for DC-DC Converter and Dynamic Load Impedance Variation Applications

    by Ruman Kalyan Mahapatra, L. Umanand, K. Gopakumar

    This work proposes a specific approach to regulate the inductance value smoothly using a flux rate-controlled adjustable inductor. The proposed adjustable inductor comprises a commercially available three-limb core, two windings, and a control switch, which gives a low-cost solution. The control switch is realized using a bidirectional switch or a variable resistance. The duty ratio or the variable resistance value controls the flux rate to adjust the inductance value. The proposed adjustable inductor is modeled using the widely used bond-graph technique to perform the simulation study. The working of the adjustable inductor is validated through several applications explained in this work. The experimentation for the DC load impedance variation application is conducted using a lab-built prototype considering both methods of flux rate control. The inductance values obtained from the experiments follow the simulation study’s calculated values. The AC load variation experimentation is performed at 500 Hz to observe the change in phase angle due to the inductance variation. This work integrates the proposed adjustable inductor with DC-DC converters to enhance the ccmdcm region. A basic PI controller performs the close loop control of the SiC-based synchronous Buck and Boost converters to validate the system stability during inductance variation.

  • Improved Trans-Z-Source Active-Neutral-Point-Clamped Multilevel Inverter With Continuous Input Current for Induction Motor Drives

    by Lallu Mol K Johny, Jaison Mathew, K. Gopakumar

    Z-source inverters (ZSIs) are recent solutions for single-stage power conversion with boosted dc rail voltage. Trans-ZSI, employing a coupled inductor, allows high boost with lower shoot-through duty ratio. Albeit the several advantages, these converters exhibit unsatisfactory performance at low power factor due to discontinuous current conduction modes—a major concern in applications like motor drives at light loads. The objective of this article is to develop an improved Trans-ZSI with multilevel output voltage that performs well irrespective of load power factor. The proposed topology has continuous input current, low input current ripple, and the presence of active switches in the impedance network allows bidirectional current flow. Also, there is output voltage control flexibility by adjusting the coupled inductor turns ratio, shoot-through time, and modulation index. Partial shoot-through states allow nearest three vector switching for obtaining multilevel output voltage and reduced dv/dt. The output stage retains all the advantages of active-neutral-point-clamped (ANPC) inverter. Operating principles, analysis and a ‘simple boost control’ with carrier-based space vector pulse width modulation (CSVPWM) scheme for capacitor balancing are presented. Simulation and hardware results on three-phase, 3 HP, 220 V, 1440 rpm, V/f-controlled induction motor drives are presented to validate the proposed scheme.


  • Integrated Magnetic Based Isolated Three Phase Inverter With Flux-Rate Controlled Harmonic Filtering

    by Ruman Kalyan Mahapatra, L. Umanand, K. Gopakumar

    This article proposes an integrated magnetic-based isolated three-phase inverter scheme. Here, the harmonic components are filtered using the flux-rate control technique. The system operates using a main and control inverter with a common dc link and a magnetic circuit. The main inverter performs a square wave mode of operation at the fundamental frequency throughout the operating range, causing lower switching losses and reduced voltage and current stresses. The control inverter performs pulse width modulation (PWM) operation and sets up the necessary flux rate in the magnetic interface, operating at a fraction of the total power rating. The integrated magnetic circuit comprises eight-limbed E-I-E lamination types. It interfaces the main inverter, control inverter, and loads, causing galvanic isolation and load side free from power electronic components to provide scaling flexibility. The bond graph modeling technique formulates the dynamic model of the system to conduct the simulation studies. A lab-built prototype validates the working of the proposed scheme. The experimental studies comprise the working of the inverter for different modulation, dynamic operations, and an induction machine's open loop v/f operation. The study includes the proposed inverter's power loss and size comparison with the conventional two-level and three-level neutral point clamp (NPC) inverters.