Nabeel Ali Bakr
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Nabeel Ali Bakr has a total of 67 co-authors. Here are the top co-authors by number of shared publications:
- Adinath M. Funde
Centre for Energy Studies (Formerly School of Energy Studies), Savitribai Phule Pune University, Pune, India
6 shared publications Sabah A. Salman
Department of Physics, College of Science, University of Diyala, Diyala, Iraq
6 shared publicationsD.P. Amalnerkar
Center for Materials for Electronics Technology (C-MET), Panchawati, Pune 411 008, India
4 shared publicationsR.R. Hawaldar
Center for Materials for Electronics Technology (C-MET), Panchawati, Pune 411 008, India
4 shared publicationsAhmed M. Shano
University of Diyala
3 shared publications- Farid Jamali-Sheini
Advanced Surface Engineering and Nano Materials Research Center, Department of Physics, Ahvaz Branch, Islamic Azad University, Ahvaz, Iran
3 shared publications
Latest Publications
- Open Access
- 1 October 2025
- Published by University of Diyala, College of Science in Academic Science Journal
- Vol. 3 (4) , 133-154
Physical Characterization of Cu2basns4 Thin Films Deposited At DifferentConcentrations of Sulfur Ions by Chemical Spray Pyrolysis Method
In this work, Cu2BaSnS4 thin films were deposited on soda-lime glass by the chemical spray pyrolysis technique (CSP) at different concentrations of thiourea, with a thickness of about 350 ±10 nm measured by the gravimetric method. The thin films structural and morphological properties were investigated using X-ray diffraction (XRD), Raman spectroscopy, Field Emission Scanning Electron Microscopy (FE-SEM), and Atomic Force Microscopy (AFM), as well as optical properties using a UV-Vis spectrophotometer at the wavelength range (300–900) nm. We investigated the electrical properties using the Hall effect. Optical band gap of CBTS thin films increased from (1.757 to 1.923) eV when concentrations of thiourea increased from (0.04 to 0.12) M. The Cu2BaSnS4 (CBTS) films have a high absorption coefficient (α > 104 cm-1), indicating allowed direct electron transmission. XRD measurements of Cu2BaSnS4 (CBTS) films revealed a trigonal crystal structure. The XRD pattern preferred the (104) orientation, which has a high intensity and indicates that crystallization is most likely to occur along this plan. Raman spectroscopy of CBTS thin films revealed a protruding peak at ~341 cm-1. The morphological findings and FE-SEM photographs of the thin film surface revealed a variety of structures and forms, one of which resembled cauliflower. Electrical tests revealed the conductivity of (p-type). The calculated electrical conductivity of CBTS thin films was found in the range of 0.053 - 0.184 (Ω.cm)-1. Based on our findings, the Cu2BaSnS4 (CBTS) thin films look to be an excellent choice for an absorber layer in solar cells.
- 1 October 2025
- Published by University of Diyala, College of Science in Academic Science Journal
- Vol. 3 (4) , 133-154
Open AccessPhysical Characterization of Cu2basns4 Thin Films Deposited At DifferentConcentrations of Sulfur Ions by Chemical Spray Pyrolysis Method
In this work, Cu2BaSnS4 thin films were deposited on soda-lime glass by the chemical spray pyrolysis technique (CSP) at different concentrations of thiourea, with a thickness of about 350 ±10 nm measured by the gravimetric method. The thin films structural and morphological properties were investigated using X-ray diffraction (XRD), Raman spectroscopy, Field Emission Scanning Electron Microscopy (FE-SEM), and Atomic Force Microscopy (AFM), as well as optical properties using a UV-Vis spectrophotometer at the wavelength range (300–900) nm. We investigated the electrical properties using the Hall effect. Optical band gap of CBTS thin films increased from (1.757 to 1.923) eV when concentrations of thiourea increased from (0.04 to 0.12) M. The Cu2BaSnS4 (CBTS) films have a high absorption coefficient (α > 104 cm-1), indicating allowed direct electron transmission. XRD measurements of Cu2BaSnS4 (CBTS) films revealed a trigonal crystal structure. The XRD pattern preferred the (104) orientation, which has a high intensity and indicates that crystallization is most likely to occur along this plan. Raman spectroscopy of CBTS thin films revealed a protruding peak at ~341 cm-1. The morphological findings and FE-SEM photographs of the thin film surface revealed a variety of structures and forms, one of which resembled cauliflower. Electrical tests revealed the conductivity of (p-type). The calculated electrical conductivity of CBTS thin films was found in the range of 0.053 - 0.184 (Ω.cm)-1. Based on our findings, the Cu2BaSnS4 (CBTS) thin films look to be an excellent choice for an absorber layer in solar cells.
- Open Access
- 6 December 2022
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 4,p. 183-189
Preparation and Characterization of Cu2CrSnS4 Thin Films Deposited at Different Temperatures
In this study, Cu2CrSnS4 thin films are prepared using chemical pyrolysis technique at various deposition temperatures (200, 250, 300, 350, 400 and 450 °C) and without any annealing process. The structure characteristics of the films have been studied by X ray diffraction (XRD), micro-Raman spectroscopy, and Field Emission Scanning Electron Microscope (FESEM), while the optical characteristics are investigated by UV-Visible spectrophotometry, and the electrical properties aree described by Hall Effect test. Results of XRD for Cu2CrSnS4 (CCTS) films showed the tetragonal crystal structure of stannite phase with (112) preferred orientation. The results of Raman spectroscopy of the prepared CCTS thin films showed a clear peak at ~ 336 cm-1. Furthermore, the morphology results and through (FESEM) images of thin films surface showed different forms and shapes with different granular size ranging from 40 to 294 nm. Optical examination of the ultraviolet-visible spectrum showed an optical energy gap of (1.69-1.59 eV) which are considered to be suitable for thin films solar cells applications. The electrical measurements through Hall Effect test showed that the films have charge carriers of (p-type). From results analysis, the optimized temperature of the prepared (CCTS) samples was 350 oC.
- 6 December 2022
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 4,p. 183-189
Open AccessPreparation and Characterization of Cu2CrSnS4 Thin Films Deposited at Different Temperatures
In this study, Cu2CrSnS4 thin films are prepared using chemical pyrolysis technique at various deposition temperatures (200, 250, 300, 350, 400 and 450 °C) and without any annealing process. The structure characteristics of the films have been studied by X ray diffraction (XRD), micro-Raman spectroscopy, and Field Emission Scanning Electron Microscope (FESEM), while the optical characteristics are investigated by UV-Visible spectrophotometry, and the electrical properties aree described by Hall Effect test. Results of XRD for Cu2CrSnS4 (CCTS) films showed the tetragonal crystal structure of stannite phase with (112) preferred orientation. The results of Raman spectroscopy of the prepared CCTS thin films showed a clear peak at ~ 336 cm-1. Furthermore, the morphology results and through (FESEM) images of thin films surface showed different forms and shapes with different granular size ranging from 40 to 294 nm. Optical examination of the ultraviolet-visible spectrum showed an optical energy gap of (1.69-1.59 eV) which are considered to be suitable for thin films solar cells applications. The electrical measurements through Hall Effect test showed that the films have charge carriers of (p-type). From results analysis, the optimized temperature of the prepared (CCTS) samples was 350 oC.
- Open Access
- 2 September 2022
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 3,p. 84-90
Effect of Na Doping on Some Physical Properties of Chemically Sprayed CZTS Thin Films
In this work, sodium-doped copper zinc tin sulfide (CZTS) thin films are prepared by depositing them on glass substrates at temperature of (400±10) °C and thickness of (350±10) nm using Chemical Spray Pyrolysis (CSP) technique. 0.02 M of copper chloride dihydrate (CuCl2.2H2O), 0.01 M of zinc chloride (ZnCl2), 0.01 M of tin chloride dihydrate (SnCl2.2H2O), and 0.16 M of thiourea (SC(NH2)2) were used as sources of copper, zinc, tin, and sulphur ions respectively. Sodium chloride (NaCl) at different volumetric ratios of (1, 3, 5, 7 and 9) % was used as a dopant source. The solution is sprayed on glass substrates. XRD diffraction, Raman spectroscopy, FESEM, UV-Vis-NIR, and Hall effect techniques were used to investigate the structural, optical, and electrical properties of the produced films. The XRD diffraction results revealed that all films are polycrystalline, with a tetragonal structure and a preferential orientation along the (112) plane. The crystallite size of all films was estimated using Scherrer's method, and it was found that the crystallite size decreases as the doping ratio increases. The FESEM results revealed the existence of cauliflower-shaped nanoparticles. The optical energy band gap was demonstrated to have a value ranging from 1.6 to 1.51 eV with a high absorption coefficient (α ≥104 cm-1) in the visible region of the spectrum. Hall measurements showed that the conductivity of CZTS thin films with various Na doping ratios have p-type electrical conductivity, and it increases as the Na doping ratio increases.
- 2 September 2022
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 3,p. 84-90
Open AccessEffect of Na Doping on Some Physical Properties of Chemically Sprayed CZTS Thin Films
In this work, sodium-doped copper zinc tin sulfide (CZTS) thin films are prepared by depositing them on glass substrates at temperature of (400±10) °C and thickness of (350±10) nm using Chemical Spray Pyrolysis (CSP) technique. 0.02 M of copper chloride dihydrate (CuCl2.2H2O), 0.01 M of zinc chloride (ZnCl2), 0.01 M of tin chloride dihydrate (SnCl2.2H2O), and 0.16 M of thiourea (SC(NH2)2) were used as sources of copper, zinc, tin, and sulphur ions respectively. Sodium chloride (NaCl) at different volumetric ratios of (1, 3, 5, 7 and 9) % was used as a dopant source. The solution is sprayed on glass substrates. XRD diffraction, Raman spectroscopy, FESEM, UV-Vis-NIR, and Hall effect techniques were used to investigate the structural, optical, and electrical properties of the produced films. The XRD diffraction results revealed that all films are polycrystalline, with a tetragonal structure and a preferential orientation along the (112) plane. The crystallite size of all films was estimated using Scherrer's method, and it was found that the crystallite size decreases as the doping ratio increases. The FESEM results revealed the existence of cauliflower-shaped nanoparticles. The optical energy band gap was demonstrated to have a value ranging from 1.6 to 1.51 eV with a high absorption coefficient (α ≥104 cm-1) in the visible region of the spectrum. Hall measurements showed that the conductivity of CZTS thin films with various Na doping ratios have p-type electrical conductivity, and it increases as the Na doping ratio increases.
- Open Access
- 1 June 2021
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 790 (1) , 012085
Synthesis, Characterization and H2S Gas Sensor Performance of Hydrothermal Prepared SnO2 Films Nanostructures
In this work, tin oxide thin films were successfully synthesized by hydrothermal method and depositing on silicon substrates by spin coating technique at room temperature with thickness of about 325±5 nm. The structural, surface morphological, optical and gas sensor properties have been investigated. The XRD results showed that SnO2 films are polycrystalline in nature with tetragonal. The FESEM images of SnO2 clearly indicate that the oxide possesses has like cauliflower like shapes. The optical properties show that the optical energy gap follows allowed direct electronic transition calculated using Tauc’s equation. The H2S toxic gas sensing properties of SnO2 thin film are examined as a function of time and operating temperature. High sensitivity (197%) was attained at operating temperature of 200 °C with fast response and recovery times.
- 1 June 2021
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 790 (1) , 012085
Open AccessSynthesis, Characterization and H2S Gas Sensor Performance of Hydrothermal Prepared SnO2 Films Nanostructures
In this work, tin oxide thin films were successfully synthesized by hydrothermal method and depositing on silicon substrates by spin coating technique at room temperature with thickness of about 325±5 nm. The structural, surface morphological, optical and gas sensor properties have been investigated. The XRD results showed that SnO2 films are polycrystalline in nature with tetragonal. The FESEM images of SnO2 clearly indicate that the oxide possesses has like cauliflower like shapes. The optical properties show that the optical energy gap follows allowed direct electronic transition calculated using Tauc’s equation. The H2S toxic gas sensing properties of SnO2 thin film are examined as a function of time and operating temperature. High sensitivity (197%) was attained at operating temperature of 200 °C with fast response and recovery times.
- Open Access
- 30 October 2020
- Published by Papers in Physics in Papers in Physics
- Vol. 12, 120006
The electrical and mechanical properties of Cadmium chloride reinforced PVA:PVP blend films
In this study, pure polymer blend (PVA:PVP) film and salt (CdCl2·H2O) reinforced polymer blend films were prepared at different weight ratios (10 wt%, 20 wt%, 40 wt%) using the casting method. The effect of the salt weight ratio on the dielectric properties of the polymer blend films reinforced by CdCl2·H2O salt were investigated, and the experimental results showed that the dielectric constant and the dielectric loss factor decreased as the frequency increased for all polymer blend films. Moreover, the above-mentioned properties increased with increasing salt weight ratios at the same frequency. The experimental results also showed an increase in AC electrical conductivity with increasing frequency, for all polymer blend films, and the AC electrical conductivity also increased with an increase in the weight ratio of the salt at the same frequency. The effect of the salt weight ratio on the mechanical properties of the salt-reinforced PVA:PVP polymer blend films was also studied. The experimental results obtained from the tensile test of the salt-reinforced polymer blend films show significant change in the values of tensile strength, elongation at break, and Young’s modulus with increasing salt weight ratios; the hardness value first increases then decreases with increasing salt weight ratios, and the fracture energy value increases with increasing salt weight ratios, thus they could be good candidates for hard adhesives with low flexibility.
- 30 October 2020
- Published by Papers in Physics in Papers in Physics
- Vol. 12, 120006
Open AccessThe electrical and mechanical properties of Cadmium chloride reinforced PVA:PVP blend films
In this study, pure polymer blend (PVA:PVP) film and salt (CdCl2·H2O) reinforced polymer blend films were prepared at different weight ratios (10 wt%, 20 wt%, 40 wt%) using the casting method. The effect of the salt weight ratio on the dielectric properties of the polymer blend films reinforced by CdCl2·H2O salt were investigated, and the experimental results showed that the dielectric constant and the dielectric loss factor decreased as the frequency increased for all polymer blend films. Moreover, the above-mentioned properties increased with increasing salt weight ratios at the same frequency. The experimental results also showed an increase in AC electrical conductivity with increasing frequency, for all polymer blend films, and the AC electrical conductivity also increased with an increase in the weight ratio of the salt at the same frequency. The effect of the salt weight ratio on the mechanical properties of the salt-reinforced PVA:PVP polymer blend films was also studied. The experimental results obtained from the tensile test of the salt-reinforced polymer blend films show significant change in the values of tensile strength, elongation at break, and Young’s modulus with increasing salt weight ratios; the hardness value first increases then decreases with increasing salt weight ratios, and the fracture energy value increases with increasing salt weight ratios, thus they could be good candidates for hard adhesives with low flexibility.
- 30 April 2018
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 29 (13) , 11208-11214
H2S gas sensitivity of PAni nano fibers synthesized by hydrothermal method
- 30 April 2018
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 29 (13) , 11208-11214
H2S gas sensitivity of PAni nano fibers synthesized by hydrothermal method
- Open Access
- 10 April 2018
- Published by AOA Academic Open Access Ltd. in International Letters of Chemistry, Physics and Astronomy
- Vol. 78, 30-38
A Study of FTIR and some Mechanical Properties of Sodium Iodide (NaI) Salt Filled Polymer Polyvinyl Alcohol (PVA) Films
The effect of Sodium Iodide (NaI) salt on mechanical properties of polyvinyl alcohol (PVA) was studied in this work. The interaction between (NaI) salt and polymer (PVA) was investigated by (FTIR) spectroscopy. The effect of (NaI) salt on the mechanical properties of the polymer (PVA) was studied by hardness and tensile tests. FTIR spectra analysis of pure and (NaI) filled (PVA) films showed that the vibrational modes have changed due to the effect of filler salt in the polymer (PVA). Hardness test showed that the hardness increases unsystematically with increasing the weight ratio of added sodium iodide salt except the weight ratio of (16 wt %) compared with pure (PVA) film, while the experimental results of the tensile test for (PVA-NaI) composite films showed unsystematic change of tensile strength, elongation at break and Young's modulus after filling with different weight ratios of (NaI) salt compared with pure (PVA) film.
- 10 April 2018
- Published by AOA Academic Open Access Ltd. in International Letters of Chemistry, Physics and Astronomy
- Vol. 78, 30-38
Open AccessA Study of FTIR and some Mechanical Properties of Sodium Iodide (NaI) Salt Filled Polymer Polyvinyl Alcohol (PVA) Films
The effect of Sodium Iodide (NaI) salt on mechanical properties of polyvinyl alcohol (PVA) was studied in this work. The interaction between (NaI) salt and polymer (PVA) was investigated by (FTIR) spectroscopy. The effect of (NaI) salt on the mechanical properties of the polymer (PVA) was studied by hardness and tensile tests. FTIR spectra analysis of pure and (NaI) filled (PVA) films showed that the vibrational modes have changed due to the effect of filler salt in the polymer (PVA). Hardness test showed that the hardness increases unsystematically with increasing the weight ratio of added sodium iodide salt except the weight ratio of (16 wt %) compared with pure (PVA) film, while the experimental results of the tensile test for (PVA-NaI) composite films showed unsystematic change of tensile strength, elongation at break and Young's modulus after filling with different weight ratios of (NaI) salt compared with pure (PVA) film.
- Open Access
- 17 October 2016
- Published by Science Publishing Group in International Journal of Materials Science and Applications
- Vol. 5 (6) , 261-270
Influence of Thiourea Concentration on Some Physical Properties of Chemically Sprayed Cu 2 ZnSnS 4 Thin Films
In this work Cu 2 ZnSnS 4 (CZTS) films were deposited by using chemical spray pyrolysis (CSP) technique at substrate temperature of (400 ± 10) °C and thickness of about (300 ± 10) nm at different Thiourea Concentrations of (0.14, 0.16, 0.18, 0.20, 0.22 and 0.24) M. Copper chloride (CuCl), zinc chloride (ZnCl 2 ), tin chloride (SnCl 4 .5H 2 O) and thiourea (SC(NH 2 ) 2 ) were used as sources of copper ions, zinc ions, tin ions and sulfur ions respectively. The structural, morphological and optical properties of these films have been studied using XRD, AFM, and UV-Visible spectroscopy respectively. The XRD results showed that all films are polycrystalline in nature with tetragonal structure and preferred orientation along (112) plane. The crystallite size (D av ) of all samples was calculated using Scherrer’s equation and it is found that the sample deposited at thiourea concentration of 0.20 M has maximum crystallite size of 31.25 nm, while it was minimum (18.02 nm) for the sample prepared at thiourea concentration of 0.16 M. The AFM results showed smooth and homogenous thin films. The optical energy band gap (E g ) for allowed direct electronic transition was calculated using Tauc’s plot. It is found that the energy band gap (E g ) decreases as the thiourea concentration increases and it was in the range of (2.22 - 1.75) eV. Urbach energy, refractive index, extinction coefficient and dielectric coefficient of all deposited films were estimated and the results were discussed.
- 17 October 2016
- Published by Science Publishing Group in International Journal of Materials Science and Applications
- Vol. 5 (6) , 261-270
Open AccessInfluence of Thiourea Concentration on Some Physical Properties of Chemically Sprayed Cu 2 ZnSnS 4 Thin Films
In this work Cu 2 ZnSnS 4 (CZTS) films were deposited by using chemical spray pyrolysis (CSP) technique at substrate temperature of (400 ± 10) °C and thickness of about (300 ± 10) nm at different Thiourea Concentrations of (0.14, 0.16, 0.18, 0.20, 0.22 and 0.24) M. Copper chloride (CuCl), zinc chloride (ZnCl 2 ), tin chloride (SnCl 4 .5H 2 O) and thiourea (SC(NH 2 ) 2 ) were used as sources of copper ions, zinc ions, tin ions and sulfur ions respectively. The structural, morphological and optical properties of these films have been studied using XRD, AFM, and UV-Visible spectroscopy respectively. The XRD results showed that all films are polycrystalline in nature with tetragonal structure and preferred orientation along (112) plane. The crystallite size (D av ) of all samples was calculated using Scherrer’s equation and it is found that the sample deposited at thiourea concentration of 0.20 M has maximum crystallite size of 31.25 nm, while it was minimum (18.02 nm) for the sample prepared at thiourea concentration of 0.16 M. The AFM results showed smooth and homogenous thin films. The optical energy band gap (E g ) for allowed direct electronic transition was calculated using Tauc’s plot. It is found that the energy band gap (E g ) decreases as the thiourea concentration increases and it was in the range of (2.22 - 1.75) eV. Urbach energy, refractive index, extinction coefficient and dielectric coefficient of all deposited films were estimated and the results were discussed.
- Open Access
- 27 July 2016
- Published by Science Publishing Group in Advances in Materials
- Vol. 5 (4) , 23-30
Effect of Fluorine Doping on Structural and Optical Properties of SnO 2 Thin Films Prepared by Chemical Spray Pyrolysis Method
In this study, (SnO 2-x F x ) thin films where (x = 0, 0.02, 0.04, 0.06 and 0.08) have been deposited by chemical spray pyrolysis method on glass substrates at temperature of (400°C), using Tin Chloride Pentahydrate (SnCl 4 .5H 2 O) and Ammonium Fluoride (NH 4 F) solutions. The structural properties and morphology of these films have been studied using XRD and AFM respectively. XRD analysis showed that these films are polycrystalline in nature with tetragonal Rutile structure with preferred orientation of (110). Doping with Fluorine causes a decrease in the crystallite size. The optical properties for all the films were studied by recording the transmittance and absorbance spectra in the range of (300-900) nm. The results showed that the absorbance increases with increasing the doping percentage. The optical energy gap for allowed direct electronic transition was calculated and it was found that the thin film with 0.08 doping percentage has the least value of 3.72 eV. Urbach energy decreases with increasing doping percentage. The optical constants (absorption coefficient, refractive index, extinction coefficient, real and imaginary parts of dielectric constant) as a function of photon energy for all prepared films were calculated.
- 27 July 2016
- Published by Science Publishing Group in Advances in Materials
- Vol. 5 (4) , 23-30
Open AccessEffect of Fluorine Doping on Structural and Optical Properties of SnO 2 Thin Films Prepared by Chemical Spray Pyrolysis Method
In this study, (SnO 2-x F x ) thin films where (x = 0, 0.02, 0.04, 0.06 and 0.08) have been deposited by chemical spray pyrolysis method on glass substrates at temperature of (400°C), using Tin Chloride Pentahydrate (SnCl 4 .5H 2 O) and Ammonium Fluoride (NH 4 F) solutions. The structural properties and morphology of these films have been studied using XRD and AFM respectively. XRD analysis showed that these films are polycrystalline in nature with tetragonal Rutile structure with preferred orientation of (110). Doping with Fluorine causes a decrease in the crystallite size. The optical properties for all the films were studied by recording the transmittance and absorbance spectra in the range of (300-900) nm. The results showed that the absorbance increases with increasing the doping percentage. The optical energy gap for allowed direct electronic transition was calculated and it was found that the thin film with 0.08 doping percentage has the least value of 3.72 eV. Urbach energy decreases with increasing doping percentage. The optical constants (absorption coefficient, refractive index, extinction coefficient, real and imaginary parts of dielectric constant) as a function of photon energy for all prepared films were calculated.
- 1 April 2015
- Published by Elsevier in Materials Science in Semiconductor Processing
- Vol. 32, 172-178
Highly efficient photo-degradation of methyl blue and band gap shift of SnS nanoparticles under different sonication frequencies
- 1 April 2015
- Published by Elsevier in Materials Science in Semiconductor Processing
- Vol. 32, 172-178
Highly efficient photo-degradation of methyl blue and band gap shift of SnS nanoparticles under different sonication frequencies