Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Lawrence J. Hill has a total of 44 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A Degradable Difunctional Initiator for ATRP That Responds to Hydrogen Peroxide

    by Lawrence Hill, Hunter Sims, Ngoc Nguyen, Christopher Collins, Jeffery Palmer, Fiona Wasson

    Mid-chain degradable polymers can be prepared by atom transfer radical polymerization from difunctional initiators that include triggers for the desired stimuli. While many difunctional initiators can respond to reducing conditions, procedures to prepare difunctional initiators that respond to oxidizing conditions are significantly less available in the literature. Here, a difunctional initiator incorporating an oxidizable boronic ester trigger was synthesized over four steps using simple and scalable procedures. Methyl methacrylate was polymerized by atom transfer radical polymerization using this initiator, and the polymerization kinetics were consistent with a controlled polymerization. The polymer synthesized using the difunctional initiator was found to decrease in molecular weight by 58% in the presence of hydrogen peroxide, while a control experiment using poly(methyl methacrylate) without a degradable linkage showed a much smaller decrease in molecular weight of only 9%. These observed molecular weight decreases were consistent with cleavage of the difunctional initiator via a quinone methide shift and hydrolysis of the methyl ester pendent groups in both polymers, and both polymers increased in polydispersity after oxidative degradation.


  • Open Access

    Deposition of metal particles onto semiconductor nanorods using an ionic liquid

    by Michael D Ballentine, Elizabeth G Embry, Marco A Garcia, Lawrence J Hill

    The current study investigates whether metal deposition onto an existing nanorod can be carried out using an ionic liquid, and the effect this has on catalytic performance. Platinum, gold, and silver nanoparticles were deposited onto CdSe@CdS (core@shell) nanorods from metal salts in an ionic liquid (1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide) without additional surfactants or reducing agents. Photocatalytic dye degradation experiments showed that catalysts with platinum particles deposited using the ionic liquid out-performed similar materials synthesized using organic solvents and ligands. We concluded that metal particles can be deposited onto well-defined semiconductor nanorods using ionic liquids and metal salts without the need for additional reagents, and the deposited particles did not cause significant aggregation even when these materials were taken into organic media. It is possible that a broad range of metal/semiconductor heterostructured particles can be prepared using the methods reported here.


  • Subsurface Imaging of the Cores of Polymer-Encapsulated Cobalt Nanoparticles Using Force Modulation Microscopy

    by Stephen M. Deese, Lauren E. Englade-Franklin, Lawrence J. Hill, Jeffrey Pyun, Julia Y. Chan, Jayne C. Garno


  • Separation of carbon dioxide from flue gas by mixed matrix membranes using dual phase microporous polymeric constituents

    by Ali K. Sekizkardes, Victor A. Kusuma, Ganpat Dahe, Elliot A. Roth, Lawrence J. Hill, Anne Marti, Megan Macala, Surendar R. Venna, David Hopkinson

    Microporous polymeric mixed matrix membranes for CO2 separation from actual flue gas of a coal-fired power plant.


  • Open Access

    Band Edge Energetics of Heterostructured Nanorods: Photoemission Spectroscopy and Waveguide Spectroelectrochemistry of Au-Tipped CdSe Nanorod Monolayers

    by Ramanan Ehamparam, Nicholas G. Pavlopoulos, Michael W. Liao, Lawrence J. Hill, Neal R. Armstrong, Jeffrey Pyun, S. Scott Saavedra

    Conduction and valence band energies (ECB, EVB) for CdSe nanorods (NRs) functionalized with Au nanoparticle (NP) tips are reported here, referenced to the vacuum scale. We use (a) UV photoemission spectroscopy (UPS) to measure EVB for NR films, utilizing advanced approaches to secondary electron background correction, satellite removal to enhance spectral contrast, and correction for shifts in local vacuum levels; and (b) waveguide-based spectroelectrochemistry to measure ECB from onset potentials for electron injection into NR films tethered to ITO. For untipped CdSe NRs, both approaches show EVB = 5.9–6.1 eV and ECB = 4.1–4.3 eV. Addition of Au tips alters the NR band edge energies and introduces midgap states, in ways that are predicted to influence the efficiency of these nanomaterials as photoelectrocatalysts. UPS results show that Au tipping shifts EVB closer to vacuum by up to 0.4 eV, shifts the apparent Fermi energy toward the middle of the band gap, and introduces additional states above EVB. Spectroelectrochemical results confirm these trends: Au tipping shifts ECB closer to vacuum, by 0.4–0.6 eV, and introduces midgap states below ECB, which are assigned as metal–semiconductor interface (MSI) states. Characterization of these band edge energies and understanding the origins of MSI states is needed to design energy conversion systems with proper band alignment between the light absorbing NR, the NP catalyst, and solution electron donors and acceptors. The complementary characterization protocols presented here should be applicable to a wide variety of thin films of heterogeneous photoactive nanomaterials, aiding in the identification of the most promising material combinations for photoelectrochemical energy conversion.


  • Improving the Charge Conductance of Elemental Sulfur via Tandem Inverse Vulcanization and Electropolymerization

    by Philip T. Dirlam, Adam G. Simmonds, R. Clayton Shallcross, Kyle J. Arrington, Woo Jin Chung, Jared J. Griebel, Lawrence J. Hill, Richard S. Glass, Kookheon Char, Jeffrey Pyun

    The synthesis of polymeric materials using elemental sulfur (S8) as the chemical feedstock has recently been developed using a process termed inverse vulcanization. The preparation of chemically stable sulfur copolymers was previously prepared by the inverse vulcanization of S8 and 1,3-diisopropenylbenzene (DIB); however, the development of synthetic methods to introduce new chemical functionality into this novel class of polymers remains an important challenge. In this report the introduction of polythiophene segments into poly(sulfur-random-1,3-diisopropenylbenzene) is achieved by the inverse vulcanization of S8 with a styrenic functional 3,4-propylenedioxythiophene (ProDOT-Sty) and DIB, followed by electropolymerization of ProDOT side chains. This methodology demonstrates for the first time a facile approach to introduce new functionality into sulfur and high sulfur content polymers, while specifically enhancing the charge conductivity of these intrinsically highly resistive materials.


  • Colloidal polymers from inorganic nanoparticle monomers

    by Lawrence J. Hill, Nicola Pinna, Kookheon Char, Jeffrey Pyun


  • Colloidal Polymers via Dipolar Assembly of Magnetic Nanoparticle Monomers

    by Lawrence J. Hill, Jeffrey Pyun

    In this Spotlight on Applications, we describe our recent progress in the preparation of hierarchical one-dimensional (1-D) materials constructed from polymer-coated ferromagnetic cobalt nanoparticles. We begin with a general discussion of nanoparticles capable of 1-D self-organization to form 1-D assemblies, which we term colloidal polymers. The need for efficient, highly directional interactions prompted our investigation with polymer-coated ferromagnetic nanoparticles, which spontaneously form linear assemblies through coupling of north and south magnetic poles present in these single-domain ferromagnetic nanoparticles. These highly directional N–S interactions and the resulting formation of 1-D assemblies can be understood in the context of traditional polymer-forming reactions. The dipolar assembly of these ferromagnetic nanoparticles into chains and binary assemblies while dispersed in organic media has been investigated as a key foundation to form novel magnetic materials and heterostructured nanocomposites. These studies enabled the fabrication of magnetic nanoactuating systems resembling “artificial cilia and flagella”. We then discuss our recent efforts to prepare cobalt oxide nanowires using various nanoparticle conversion reactions through a process termed colloidal polymerization. A series of novel functional “colloidal monomers” based on dipolar cobalt nanoparticles were also prepared, incorporating noble metal or semiconductor nanoinclusions to form heterostructured cobalt oxide nanocomposites.


  • Polyoctadecyl methacrylate brushes via surface‐initiated atom transfer radical polymerization

    by Heemin Yoo, Bo Yun Kim, Lawrence J. Hill, Jared J. Griebel, Woo Jin Chung, Jeffrey Pyun

    The synthesis of poly(octadecyl methacrylate) brushes on planar Si substrates using surface‐initiated atom transfer radical polymerization (SI‐ATRP) is reported. SI‐ATRP of octadecyl methacrylate from a silane initiator‐modified Si substrate yielded well‐defined homopolymer brushes of varying molar mass (5000–38 000 g mol−1) and film thickness from around 2 to 20 nm. Correlation of both free polymer molar mass and brush thicknesses confirmed controlled surface‐initiated ATRP from these modified surfaces. By optimization of brush molar mass, film thickness and thin‐film processing, we observed side chain crystallization of tethered poly(octadecyl methacrylate) chains, resulting in the formation of lamellar morphologies with high‐aspect‐ratio nanofibers. Copyright © 2013 John Wiley & Sons, Ltd.


  • Single chain polymer nanoparticles via sequential ATRP and oxidative polymerization

    by Philip T. Dirlam, Hyo Ju Kim, Kyle J. Arrington, Woo Jin Chung, Rabindra Sahoo, Lawrence J. Hill, Philip J. Costanzo, Patrick Theato, Kookheon Char, Jeffrey Pyun

    The synthesis of single chain nanoparticles has been achieved by the synthesis of a linear polystyrenic precursor carrying 3,4-propylenedioxythiophene groups via atom transfer radical polymerization followed by intramolecular crosslinking via oxidative polymerization. This methodology enabled the introduction of electroactive inclusions into single chain polymer nanoparticles, while concurrently promoting intramolecular collapse.