Yue Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yue Wu has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
Shuisheng Jian
Key Laboratory of All Optical Network and Advanced Telecommunication Network, Ministry of Education, Institute of Lightwave Technology, Beijing Jiaotong University, Beijing, China
4 shared publications- Ya Shen
Key Laboratory of All Optical Network and Advanced Telecommunication Network of EMC, Institute of Lightwave Technology, Beijing Jiaotong University, Beijing, China
4 shared publications - Youchao Jiang
Beijing Jiaotong University
4 shared publications - Yuguang Yang
Ximalaya Inc ShangHai China
4 shared publications - Wenxing Jin
Key Laboratory of All Optical Network and Advanced Telecommunication Network of EMC, Institute of Lightwave Technology, Beijing Jiaotong University, Beijing, China
3 shared publications - Guobin Ren
Beijing Jiaotong University
2 shared publications
Latest Publications
- Open Access
- 28 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 10 (1) , 1-9
Refractive Index and Temperature Sensing Based on an Optoelectronic Oscillator Incorporating a Fabry–Perot Fiber Bragg Grating
A novel high-speed and high-sensitivity refractive index (RI) and temperature sensing based on an optoelectronic oscillator (OEO) is proposed and demonstrated. A novel Fabry-Perot fiber Bragg grating (FP-FBG), incorporated in the OEO to implement a microwave photonic filter, has a narrow notch in the reflection spectrum and combines a gap with two FBGs in a silica V-sharp slot. A microwave signal is generated by the OEO whose oscillating frequency is determined by the center frequency of the FP-FBG notch. The RI or the temperature change can be measured by monitoring the frequency shift of the microwave signal using an electrical spectrum analyzer or a digital signal processor. An experiment is performed to verify the proposal. The sensing sensitivities of the RI and temperature as high as 413.8 MHz/0.001RIU and 2516 MHz/°C are demonstrated respectively.
- 28 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 10 (1) , 1-9
Open AccessRefractive Index and Temperature Sensing Based on an Optoelectronic Oscillator Incorporating a Fabry–Perot Fiber Bragg Grating
A novel high-speed and high-sensitivity refractive index (RI) and temperature sensing based on an optoelectronic oscillator (OEO) is proposed and demonstrated. A novel Fabry-Perot fiber Bragg grating (FP-FBG), incorporated in the OEO to implement a microwave photonic filter, has a narrow notch in the reflection spectrum and combines a gap with two FBGs in a silica V-sharp slot. A microwave signal is generated by the OEO whose oscillating frequency is determined by the center frequency of the FP-FBG notch. The RI or the temperature change can be measured by monitoring the frequency shift of the microwave signal using an electrical spectrum analyzer or a digital signal processor. An experiment is performed to verify the proposal. The sensing sensitivities of the RI and temperature as high as 413.8 MHz/0.001RIU and 2516 MHz/°C are demonstrated respectively.
- 2 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 29 (23) , 2008-2011
Switchable Optoelectronic Oscillator Using an FM-PS-FBG for Strain and Temperature Sensing
By incorporating a phase-shifted fiber Bragg grating (PS-FBG) inscribed in few-mode fiber (FMF) named FM-PS-FBG for the first time, a novel frequency-switchable optoelectronic oscillator (OEO) to perform simultaneous strain and temperature measurement is proposed and experimentally demonstrated. In the OEO loop, two switchable oscillation frequencies are determined by the reflected bands of FM-PS-FBG based on different mode couplings and corresponding notches. Due to the characteristics of modes, two OEO-generated microwave signals exhibit different strain and temperature sensitivities. Therefore, through monitoring the frequency shifts of microwave signals, the simultaneous strain and temperature sensing can be realized by the proposed OEO sensor with high-speed and high-resolution interrogation.
- 2 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 29 (23) , 2008-2011
Switchable Optoelectronic Oscillator Using an FM-PS-FBG for Strain and Temperature Sensing
By incorporating a phase-shifted fiber Bragg grating (PS-FBG) inscribed in few-mode fiber (FMF) named FM-PS-FBG for the first time, a novel frequency-switchable optoelectronic oscillator (OEO) to perform simultaneous strain and temperature measurement is proposed and experimentally demonstrated. In the OEO loop, two switchable oscillation frequencies are determined by the reflected bands of FM-PS-FBG based on different mode couplings and corresponding notches. Due to the characteristics of modes, two OEO-generated microwave signals exhibit different strain and temperature sensitivities. Therefore, through monitoring the frequency shifts of microwave signals, the simultaneous strain and temperature sensing can be realized by the proposed OEO sensor with high-speed and high-resolution interrogation.
- 13 September 2017
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 28 (10) , 105102
High-sensitivity pressure sensor based on fiber Mach–Zehnder interferometer
In this paper we propose and experimentally demonstrate an optical fiber structure sensor based on a Mach–Zehnder interferometer for pressure measurement. The fiber sensor is composed of a single-mode-no-core-single-mode structure, a section of capillary pure silica tube and refractive index matching fluid (RIMF). As the pressure decreases, the sealed air in the tube expands and the liquid level of the RIMF increases, which causes a wavelength shift of the interferometer. The measurement of the pressure variation can thus be achieved by monitoring the wavelength shift. The experimental results agree well with the numerical simulation, and a maximum pressure sensitivity of 266.6 nm M p a − 1 is achieved experimentally. Furthermore, the proposed fiber sensor has the potential to obtain higher sensitivity by enlarging the length of the air cavity.
- 13 September 2017
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 28 (10) , 105102
High-sensitivity pressure sensor based on fiber Mach–Zehnder interferometer
In this paper we propose and experimentally demonstrate an optical fiber structure sensor based on a Mach–Zehnder interferometer for pressure measurement. The fiber sensor is composed of a single-mode-no-core-single-mode structure, a section of capillary pure silica tube and refractive index matching fluid (RIMF). As the pressure decreases, the sealed air in the tube expands and the liquid level of the RIMF increases, which causes a wavelength shift of the interferometer. The measurement of the pressure variation can thus be achieved by monitoring the wavelength shift. The experimental results agree well with the numerical simulation, and a maximum pressure sensitivity of 266.6 nm M p a − 1 is achieved experimentally. Furthermore, the proposed fiber sensor has the potential to obtain higher sensitivity by enlarging the length of the air cavity.
- 21 August 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 29 (19) , 1659-1662
Generation of the Tunable Second-Order Optical Vortex Beams in Narrow Linewidth Fiber Laser
We experimentally demonstrate a narrow linewidth single-longitudinal-mode erbium-doped fiber ring laser with an output of tunable second-order optical vortex beams (OVB). The laser is based on a mode selective all-fiber fused coupler, which is composed of a single-mode fiber (SMF) and a few-mode fiber (FMF). The fused SMF-FMF coupler inserted in the cavity of the laser acts as a mode converter, which converts LP01 mode to LP21 mode group. The tunable OVB is produced by combing two even LP21 modes with orthogonal polarization directions. The tunability of second order OVB in the fiber laser is experimentally realized by adjusting a polarizer at the output end of the fiber. The 20 dB linewidth of the fiber laser is approximate 7.2 kHz.
- 21 August 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 29 (19) , 1659-1662
Generation of the Tunable Second-Order Optical Vortex Beams in Narrow Linewidth Fiber Laser
We experimentally demonstrate a narrow linewidth single-longitudinal-mode erbium-doped fiber ring laser with an output of tunable second-order optical vortex beams (OVB). The laser is based on a mode selective all-fiber fused coupler, which is composed of a single-mode fiber (SMF) and a few-mode fiber (FMF). The fused SMF-FMF coupler inserted in the cavity of the laser acts as a mode converter, which converts LP01 mode to LP21 mode group. The tunable OVB is produced by combing two even LP21 modes with orthogonal polarization directions. The tunability of second order OVB in the fiber laser is experimentally realized by adjusting a polarizer at the output end of the fiber. The 20 dB linewidth of the fiber laser is approximate 7.2 kHz.
- 12 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 29 (10) , 838-841
Simultaneous Measurement of Curvature and Temperature Based on Asymmetrical FPI
We propose and demonstrate an asymmetrical Fabry–Perot interferometric (AFPI) fiber sensor for simultaneous measurement of the curvature and temperature. The AFPI fiber sensor is comprised of a low reflective fiber Bragg grating with narrow bandwidth and a no-core fiber with broadband Fresnel reflection. The extinction ratio measured in the experiment is defined as the difference between the amplitude of the maximum peak and its left adjacent dip, which is about 6 dB. With the variation of curvature and temperature, the maximum amplitude peak wavelength of the AFPI and the extinction ratio show different responses, thus the simultaneous measurement of curvature and temperature can be achieved. From the experimental results, sensitivities of the proposed sensor for the curvature and the temperature are about 9.57 dB/m$^{-1} $ (ranging from 0.8844 to 1.0995 m$^{-1} $ for the measured extinction ratio) and 10.2 pm/°C (ranging from 10 °C to 60 °C), respectively. Such fiber sensor is simple, low cost, and compact.- 12 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 29 (10) , 838-841
Simultaneous Measurement of Curvature and Temperature Based on Asymmetrical FPI
We propose and demonstrate an asymmetrical Fabry–Perot interferometric (AFPI) fiber sensor for simultaneous measurement of the curvature and temperature. The AFPI fiber sensor is comprised of a low reflective fiber Bragg grating with narrow bandwidth and a no-core fiber with broadband Fresnel reflection. The extinction ratio measured in the experiment is defined as the difference between the amplitude of the maximum peak and its left adjacent dip, which is about 6 dB. With the variation of curvature and temperature, the maximum amplitude peak wavelength of the AFPI and the extinction ratio show different responses, thus the simultaneous measurement of curvature and temperature can be achieved. From the experimental results, sensitivities of the proposed sensor for the curvature and the temperature are about 9.57 dB/m$^{-1} $ (ranging from 0.8844 to 1.0995 m$^{-1} $ for the measured extinction ratio) and 10.2 pm/°C (ranging from 10 °C to 60 °C), respectively. Such fiber sensor is simple, low cost, and compact.- 1 May 2016
- Published by Elsevier in Optics Communications
- Vol. 366, 308-313
Strict dual-mode large-mode-area fiber with multicore structure
- 1 May 2016
- Published by Elsevier in Optics Communications
- Vol. 366, 308-313
Strict dual-mode large-mode-area fiber with multicore structure