Byungha Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Byungha Lee has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Sanghyuk An
Agency for Defense Development, Daejeon 34186, South Korea
8 shared publications - Young-Hyun Lee
Agency for Defense Development, Daejeon 34186, South Korea
5 shared publications Kyung-Seung Yang
Agency for Defense Development, Daejeon 34186, South Korea
4 shared publicationsSeong-Ho Kim
Agency for Defense Development, Daejeon, South Korea
4 shared publicationsYoungseok Bae
Agency for Defense Development, Daejeon 34186, South Korea
4 shared publicationsChuhyun Cho
2 shared publications
Latest Publications
- 30 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 47 (5) , 2343-2346
Design of a Recoil System for a Railgun
The recoil force that causes the rearward movement of the gun is generated during firing a railgun as a conventional gun. According to Newton's third law, it should be equal to the electromagnetic force that accelerates an armature. It continues to act as long as current flows in the rails even when the muzzle arc occurs immediately after the armature exits. The recoil force in a railgun increases being proportional to the square of current as current increases. A recoil system should be installed to absorb the recoil force when it is so large that a carriage cannot withstand the load transmitted directly to it. Design and experiment of the recoil system using friction springs for a railgun are described in this paper. The space and volume to place a spring type of recoil system into the carriage are required relatively small to a hydraulic type and it has a simple structure. The recoil velocity of the railgun can be rapidly down due to the excellent damping characteristics of friction springs during two or three cyclic motions after firing. The load imposed to the carriage can be reduced to over one-tenth of the recoil force with 15 mm of recoil length when about 1560 N· s of firing impulse is applied.
- 30 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 47 (5) , 2343-2346
Design of a Recoil System for a Railgun
The recoil force that causes the rearward movement of the gun is generated during firing a railgun as a conventional gun. According to Newton's third law, it should be equal to the electromagnetic force that accelerates an armature. It continues to act as long as current flows in the rails even when the muzzle arc occurs immediately after the armature exits. The recoil force in a railgun increases being proportional to the square of current as current increases. A recoil system should be installed to absorb the recoil force when it is so large that a carriage cannot withstand the load transmitted directly to it. Design and experiment of the recoil system using friction springs for a railgun are described in this paper. The space and volume to place a spring type of recoil system into the carriage are required relatively small to a hydraulic type and it has a simple structure. The recoil velocity of the railgun can be rapidly down due to the excellent damping characteristics of friction springs during two or three cyclic motions after firing. The load imposed to the carriage can be reduced to over one-tenth of the recoil force with 15 mm of recoil length when about 1560 N· s of firing impulse is applied.
- 4 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 47 (5) , 2339-2342
Numerical Analysis on the Transient Inductance Gradient of the Resistive Overlay Rail on the Sliding Electrical Contact
A resistive overlay rail for an electromagnetic launcher was tested and its inductance gradients were analyzed using 2-D and 3-D finite-element methods (FEMs). The overlay rail was consisted with outside copper rail for good conduction of current and inside steel one for the prevention of rail wear. When the armature slides along the steel rail, electrical current flows mainly through the copper rail before it reaches the armature tail and it penetrates the steel rail at the armature tail due to the velocity skin effect. The rail inductance gradient L' R is obtained with 2-D FEM in both frequency and time domains without an armature and the propulsive inductance gradient L' P are obtained with 3-D transient FEM with a moving armature. A C-shaped aluminum armature was launched with the velocity over 2 km/s on the resistive overlay rail and gouging was not induced, while it appeared in the experiment with a copper rail. Using the two obtained inductance gradients, the circuit simulation was conducted and it explains the experiment result with a good agreement.
- 4 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 47 (5) , 2339-2342
Numerical Analysis on the Transient Inductance Gradient of the Resistive Overlay Rail on the Sliding Electrical Contact
A resistive overlay rail for an electromagnetic launcher was tested and its inductance gradients were analyzed using 2-D and 3-D finite-element methods (FEMs). The overlay rail was consisted with outside copper rail for good conduction of current and inside steel one for the prevention of rail wear. When the armature slides along the steel rail, electrical current flows mainly through the copper rail before it reaches the armature tail and it penetrates the steel rail at the armature tail due to the velocity skin effect. The rail inductance gradient L' R is obtained with 2-D FEM in both frequency and time domains without an armature and the propulsive inductance gradient L' P are obtained with 3-D transient FEM with a moving armature. A C-shaped aluminum armature was launched with the velocity over 2 km/s on the resistive overlay rail and gouging was not induced, while it appeared in the experiment with a copper rail. Using the two obtained inductance gradients, the circuit simulation was conducted and it explains the experiment result with a good agreement.
- 18 December 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 46 (7) , 2730-2735
Design and Implementation of a Test Circuit of a Repetitive Critical Rate of Rise of ON-State Current for a High-Power Thyristor
A test circuit of a repetitive critical rate of rise of ON-state current (di/dt) for a high-power thyristor is designed and implemented. The operating principle of the test circuit specified in the standard IEC-60747-6 is explained in detail. The design example for the circuit to test repetitive di/dt of 300 A/μs for a thyristor having a mean ON-state current of 2200 A is presented. The value of the charging resistor is chosen by simulations considering the maximum charging current, power consumption of the charging resistor, maximum charging voltage of the capacitor, and the peak pulsed current of the thyristor. The best firing angles of the thyristor are decided based on the simulations focused on the pulsed current of the thyristor, charging diode current, apparent power of the step-up transformer, and reverse voltage of the charging diode. The repetitive di/dt test prototype of 300 A/μs, 60 Hz, and 60 shots is assembled with the Infineon light-triggered thyristor (T1503N). The design results are verified by an experiment.
- 18 December 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 46 (7) , 2730-2735
Design and Implementation of a Test Circuit of a Repetitive Critical Rate of Rise of ON-State Current for a High-Power Thyristor
A test circuit of a repetitive critical rate of rise of ON-state current (di/dt) for a high-power thyristor is designed and implemented. The operating principle of the test circuit specified in the standard IEC-60747-6 is explained in detail. The design example for the circuit to test repetitive di/dt of 300 A/μs for a thyristor having a mean ON-state current of 2200 A is presented. The value of the charging resistor is chosen by simulations considering the maximum charging current, power consumption of the charging resistor, maximum charging voltage of the capacitor, and the peak pulsed current of the thyristor. The best firing angles of the thyristor are decided based on the simulations focused on the pulsed current of the thyristor, charging diode current, apparent power of the step-up transformer, and reverse voltage of the charging diode. The repetitive di/dt test prototype of 300 A/μs, 60 Hz, and 60 shots is assembled with the Infineon light-triggered thyristor (T1503N). The design results are verified by an experiment.
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 45 (7) , 1639-1643
Dynamic Response of an Electromagnetic Launcher Accelerating a C-Shaped Armature
A C-shaped armature in an electromagnetic launcher creates the magnetic pressure on the rear surface of the armature. The transverse component of the magnetic pressure plays a main role to maintain the moving contact between the rails and the armature. It is larger than the repulsive pressure acting against the rails far away from the armature. It might cause the dynamic deflection to be amplified along the entire length of the rails, resulting in the magnification of the contact pressure when the elastic waves of the rails pass through the contact surface. In this paper the dynamic system is modeled as a Timoshenko beam on an elastic foundation subjected to an accelerating pressure combined with the repulsive pressure and the transverse component of the magnetic pressure. The spatial and time history of the accelerating pressure as an applied force of the governing equation is calculated using the experimental current and armature position in the launcher. The influence of the magnetic pressure on the rail deflection is described in point of propagation of the elastic waves. The dynamic deflections at different positions on the rail are compared to show that the dynamic behavior of the rail is strongly affected by the moving velocity of the armature.
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 45 (7) , 1639-1643
Dynamic Response of an Electromagnetic Launcher Accelerating a C-Shaped Armature
A C-shaped armature in an electromagnetic launcher creates the magnetic pressure on the rear surface of the armature. The transverse component of the magnetic pressure plays a main role to maintain the moving contact between the rails and the armature. It is larger than the repulsive pressure acting against the rails far away from the armature. It might cause the dynamic deflection to be amplified along the entire length of the rails, resulting in the magnification of the contact pressure when the elastic waves of the rails pass through the contact surface. In this paper the dynamic system is modeled as a Timoshenko beam on an elastic foundation subjected to an accelerating pressure combined with the repulsive pressure and the transverse component of the magnetic pressure. The spatial and time history of the accelerating pressure as an applied force of the governing equation is calculated using the experimental current and armature position in the launcher. The influence of the magnetic pressure on the rail deflection is described in point of propagation of the elastic waves. The dynamic deflections at different positions on the rail are compared to show that the dynamic behavior of the rail is strongly affected by the moving velocity of the armature.
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 45 (7) , 1635-1638
Numerical Analysis of the Transient Inductance Gradient of Electromagnetic Launcher Using 2-D and 3-D Finite-Element Methods
We present analyses of the transient inductance gradient of an electromagnetic launcher with the sliding contact between rails and armature. When the armature moves along the rails, electrical current concentrates on the contact trailing edge of the armature due to the velocity skin effect, affecting input current spreading into the rail. This effect also induces the temporal variation of inductance gradient. Using the 2-D finite-element method (FEM), the rail inductance gradient without an armature is calculated and compared with the propulsive inductance gradient with a moving armature calculated by 3-D FEM. Using the 3-D simulation, the influence of the step on the height difference between the rail and the transient moving armature is investigated. The result shows that the average of transient inductance gradients during acceleration is 10% larger than Kerrisk’s inductance gradient. Also, we found that the axial force on the armature is not significantly affected by the velocity of the armature, while the lateral force on it whose direction is outside the rail increases with the velocity. The circuit simulation using both inductance gradients shows good agreement with the measured current and velocity.
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 45 (7) , 1635-1638
Numerical Analysis of the Transient Inductance Gradient of Electromagnetic Launcher Using 2-D and 3-D Finite-Element Methods
We present analyses of the transient inductance gradient of an electromagnetic launcher with the sliding contact between rails and armature. When the armature moves along the rails, electrical current concentrates on the contact trailing edge of the armature due to the velocity skin effect, affecting input current spreading into the rail. This effect also induces the temporal variation of inductance gradient. Using the 2-D finite-element method (FEM), the rail inductance gradient without an armature is calculated and compared with the propulsive inductance gradient with a moving armature calculated by 3-D FEM. Using the 3-D simulation, the influence of the step on the height difference between the rail and the transient moving armature is investigated. The result shows that the average of transient inductance gradients during acceleration is 10% larger than Kerrisk’s inductance gradient. Also, we found that the axial force on the armature is not significantly affected by the velocity of the armature, while the lateral force on it whose direction is outside the rail increases with the velocity. The circuit simulation using both inductance gradients shows good agreement with the measured current and velocity.
- 31 December 2015
- Published by The Korean Magnetics Society in Journal of Magnetics
- Vol. 20 (4) , 394-399
Modeling of 3-stage Electromagnetic Induction Launcher
Modeling of 3-stage Electromagnetic Induction Launcher induction launcher;mutual inductance;pulsed power;driving coils;finite element analysis; Electromagnetic Induction Launchers (EIL) have been receiving great attention due to their advantages of non-contact between the coils and a projectile. This paper describes the modeling and design of 3-stage EIL to accelerate a copper projectile of 50 kg with 290 mm diameter. Our EIL consists of three independent driving coils and pulsed power modules to generate separate driving currents. To find efficient acceleration conditions, the appropriate shape of the driving coils and the position of the projectile have been calculated by using a finite element analysis (FEA) method. The results showed that the projectile can be accelerated more effectively as the gap between the coils is smaller; a final velocity of 45 m/s was obtained. The acceleration efficiency was estimated to be 23.4% when a total electrical energy of 216 kJ was discharged.
- 31 December 2015
- Published by The Korean Magnetics Society in Journal of Magnetics
- Vol. 20 (4) , 394-399
Modeling of 3-stage Electromagnetic Induction Launcher
Modeling of 3-stage Electromagnetic Induction Launcher induction launcher;mutual inductance;pulsed power;driving coils;finite element analysis; Electromagnetic Induction Launchers (EIL) have been receiving great attention due to their advantages of non-contact between the coils and a projectile. This paper describes the modeling and design of 3-stage EIL to accelerate a copper projectile of 50 kg with 290 mm diameter. Our EIL consists of three independent driving coils and pulsed power modules to generate separate driving currents. To find efficient acceleration conditions, the appropriate shape of the driving coils and the position of the projectile have been calculated by using a finite element analysis (FEA) method. The results showed that the projectile can be accelerated more effectively as the gap between the coils is smaller; a final velocity of 45 m/s was obtained. The acceleration efficiency was estimated to be 23.4% when a total electrical energy of 216 kJ was discharged.
- 30 January 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 42 (3) , 853-858
Transient Analysis of Circuit Containing Massive Conductors
Inductive electrical components made of massive conductors are usually adopted in the high-power circuit. Since they are not the types of filaments, the diffusion of the electromagnetic fields inside the conductors plays an important role in the transient discharge. Though the behavior of the circuit can be described reasonably using constant electrical parameters, the voltage drop in the massive conductor is not expressed accurately when constant resistance and inductance are used in the analysis of the transient discharge. To obtain a more accurate waveform of the pulsed current, we have used a comprehensive method calculating the correction voltage in the voltage drop. Once the resistive voltage drop and the magnetic flux for a step-function current are obtained either analytically or numerically, the voltage drop in the massive component for any current waveform can be calculated using the Duhamel's integration. The equations of the circuit containing massive conductors can be solved through a few iterations using the method estimating the voltage drop. As an example, the method was applied to an analysis of an RLC circuit containing a massive pulse-forming inductor. Electromagnetic responses of the inductor for a step-function current were calculated numerically with the help of a finite element method. The current waveform calculated using the method of correction voltage showed a good agreement with the measured waveforms.
- 30 January 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 42 (3) , 853-858
Transient Analysis of Circuit Containing Massive Conductors
Inductive electrical components made of massive conductors are usually adopted in the high-power circuit. Since they are not the types of filaments, the diffusion of the electromagnetic fields inside the conductors plays an important role in the transient discharge. Though the behavior of the circuit can be described reasonably using constant electrical parameters, the voltage drop in the massive conductor is not expressed accurately when constant resistance and inductance are used in the analysis of the transient discharge. To obtain a more accurate waveform of the pulsed current, we have used a comprehensive method calculating the correction voltage in the voltage drop. Once the resistive voltage drop and the magnetic flux for a step-function current are obtained either analytically or numerically, the voltage drop in the massive component for any current waveform can be calculated using the Duhamel's integration. The equations of the circuit containing massive conductors can be solved through a few iterations using the method estimating the voltage drop. As an example, the method was applied to an analysis of an RLC circuit containing a massive pulse-forming inductor. Electromagnetic responses of the inductor for a step-function current were calculated numerically with the help of a finite element method. The current waveform calculated using the method of correction voltage showed a good agreement with the measured waveforms.
- 16 August 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 41 (10) , 2671-2674
Fabrication and Testing of a 600-kJ Pulsed Power System
A 600-kJ pulsed power system (PPS) was built for various applications. The PPS consists of six 100-kJ unit modules. A single unit module is composed of a capacitor, a thyristor switch stack, a crowbar diode stack, and a pulse forming inductor. The module was designed to be operational for a maximum charging voltage of 10 kV and a peak current up to 75 kA. Each module can be triggered and controlled independently by a control computer via fiber optic communication. The six modules are combined into one frame and are charged to the same voltage by one capacitor charger. The design, fabrication and test results of the unit modules, and the 600 kJ PPS are presented in this paper.
- 16 August 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 41 (10) , 2671-2674
Fabrication and Testing of a 600-kJ Pulsed Power System
A 600-kJ pulsed power system (PPS) was built for various applications. The PPS consists of six 100-kJ unit modules. A single unit module is composed of a capacitor, a thyristor switch stack, a crowbar diode stack, and a pulse forming inductor. The module was designed to be operational for a maximum charging voltage of 10 kV and a peak current up to 75 kA. Each module can be triggered and controlled independently by a control computer via fiber optic communication. The six modules are combined into one frame and are charged to the same voltage by one capacitor charger. The design, fabrication and test results of the unit modules, and the 600 kJ PPS are presented in this paper.