Nurettin Korozlu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Nurettin Korozlu has a total of 46 co-authors. Here are the top co-authors by number of shared publications:
- Ahmet Cicek
Mehmet Akif Ersoy University
15 shared publications - Engin Deligoz
Department of Physics, Aksaray University, Aksaray, Türkiye
9 shared publications K. Colakoglu
7 shared publications- Gokhan Surucu
Department of Energy Systems Engineering Faculty of Technology Gazi University Ankara Türkiye
6 shared publications - Ahmet Biçer
Department of Physics Faculty of Arts and Science Burdur Mehmet Akif Ersoy University Burdur Türkiye
4 shared publications - Olgun Adem Kaya
Department of Computer Education and Educational Technology, Faculty of Education, Inonu University 2 , 44280 Malatya, Turkey
4 shared publications
Latest Publications
- 23 October 2026
- Published by Elsevier in Photonics and Nanostructures - Fundamentals and Applications
- Vol. 72
Chirp engineering for UV–violet attenuation in compact TiO2/SiO2 multilayers
- 23 October 2026
- Published by Elsevier in Photonics and Nanostructures - Fundamentals and Applications
- Vol. 72
Chirp engineering for UV–violet attenuation in compact TiO2/SiO2 multilayers
- Open Access
Experimental Investigation of Metamaterial-Inspired Periodic Foundation Systems with Embedded Piezoelectric Layers for Seismic Vibration Attenuation
Seismic metamaterial-inspired periodic foundations have emerged as promising vibration-mitigation concepts capable of attenuating seismic wave propagation within specific frequency bands. This study presents an experimental investigation on the dynamic response of periodic foundation configurations, with and without embedded piezoelectric layers, to evaluate their vibration-attenuation characteristics. The experimental program employed a shake table driven by a 0.75 kW servo motor and included excitation step counts of 3000, 4000, and 5000. Accelerometers mounted on the specimen surfaces recorded vibration data at 80 ms intervals. Three foundation configurations were tested: (i) a conventional reinforced concrete block, (ii) a one-dimensional periodic foundation composed of alternating concrete and rubber layers, and (iii) a periodic foundation incorporating piezoelectric modules. Time-domain and frequency-domain analyses showed that the periodic foundations achieved notable reductions in both peak and RMS accelerations, especially near resonance frequencies. The configuration, including piezoelectric layers, exhibited similar attenuation performance while also generating measurable instantaneous voltage outputs under vibration. However, these voltage peaks—reaching a maximum of 1.64 V—represent only a laboratory-scale, proof-of-concept demonstration of electromechanical coupling rather than a practical or continuous form of energy harvesting, given the inherently sporadic nature of seismic excitation. Overall, the results confirm that the tested system is not a full metamaterial in the classical sense but rather a metamaterial-inspired periodic arrangement capable of inducing band-gap-based vibration attenuation. The inclusion of piezoelectric elements provides auxiliary sensing and micro-energy-generation capabilities, offering a preliminary foundation for future multifunctional seismic-protection concepts.
Open AccessExperimental Investigation of Metamaterial-Inspired Periodic Foundation Systems with Embedded Piezoelectric Layers for Seismic Vibration Attenuation
Seismic metamaterial-inspired periodic foundations have emerged as promising vibration-mitigation concepts capable of attenuating seismic wave propagation within specific frequency bands. This study presents an experimental investigation on the dynamic response of periodic foundation configurations, with and without embedded piezoelectric layers, to evaluate their vibration-attenuation characteristics. The experimental program employed a shake table driven by a 0.75 kW servo motor and included excitation step counts of 3000, 4000, and 5000. Accelerometers mounted on the specimen surfaces recorded vibration data at 80 ms intervals. Three foundation configurations were tested: (i) a conventional reinforced concrete block, (ii) a one-dimensional periodic foundation composed of alternating concrete and rubber layers, and (iii) a periodic foundation incorporating piezoelectric modules. Time-domain and frequency-domain analyses showed that the periodic foundations achieved notable reductions in both peak and RMS accelerations, especially near resonance frequencies. The configuration, including piezoelectric layers, exhibited similar attenuation performance while also generating measurable instantaneous voltage outputs under vibration. However, these voltage peaks—reaching a maximum of 1.64 V—represent only a laboratory-scale, proof-of-concept demonstration of electromechanical coupling rather than a practical or continuous form of energy harvesting, given the inherently sporadic nature of seismic excitation. Overall, the results confirm that the tested system is not a full metamaterial in the classical sense but rather a metamaterial-inspired periodic arrangement capable of inducing band-gap-based vibration attenuation. The inclusion of piezoelectric elements provides auxiliary sensing and micro-energy-generation capabilities, offering a preliminary foundation for future multifunctional seismic-protection concepts.
- Open Access
- 26 March 2025
- Published by Bingol Universitesi in Türk Doğa ve Fen Dergisi
- Vol. 14 (1) , 197-203
Deterministic Lateral Displacement System with Inclined Elliptical Obstacles for Efficient Size-Based Separation of Microparticles
A deterministic lateral displacement system with inclined elliptical posts is demonstrated to sort spherical micrometer-sized solid particles. Numerical simulations via the finite-element method are performed to investigate the microfluidic system performance. Soft microparticles undergo deformations in designs with cylindrical posts or posts with sharp corners. Such deformations occur due to particle clogging between obstacles, which can disrupt the flow lanes. The proposed approach aims to eliminate these challenges. The calculations reveal a much-reduced rate of change in flow velocity between vertically inclined elliptical posts, compared to circular posts. The calculated critical particle sizes are more likely to follow the equation associated with the first flow lane width derived from a parabolic velocity profile at high fluid inlet rates, rather than the two semi-analytical models proposed for circular posts. The experimental and theoretical critical diameter data exhibited greater agreement with the critical diameter equation obtained using the curve-fitting method at lower fluid inlet rates. Overall, the minimum particle size decreased as the rate of flow increased. When assessing the connection between the two, a smaller critical diameter is achieved by decreasing the inclination angle. The adjustability of the system by rotating the posts is a major advantage of the proposed approach.
- 26 March 2025
- Published by Bingol Universitesi in Türk Doğa ve Fen Dergisi
- Vol. 14 (1) , 197-203
Open AccessDeterministic Lateral Displacement System with Inclined Elliptical Obstacles for Efficient Size-Based Separation of Microparticles
A deterministic lateral displacement system with inclined elliptical posts is demonstrated to sort spherical micrometer-sized solid particles. Numerical simulations via the finite-element method are performed to investigate the microfluidic system performance. Soft microparticles undergo deformations in designs with cylindrical posts or posts with sharp corners. Such deformations occur due to particle clogging between obstacles, which can disrupt the flow lanes. The proposed approach aims to eliminate these challenges. The calculations reveal a much-reduced rate of change in flow velocity between vertically inclined elliptical posts, compared to circular posts. The calculated critical particle sizes are more likely to follow the equation associated with the first flow lane width derived from a parabolic velocity profile at high fluid inlet rates, rather than the two semi-analytical models proposed for circular posts. The experimental and theoretical critical diameter data exhibited greater agreement with the critical diameter equation obtained using the curve-fitting method at lower fluid inlet rates. Overall, the minimum particle size decreased as the rate of flow increased. When assessing the connection between the two, a smaller critical diameter is achieved by decreasing the inclination angle. The adjustability of the system by rotating the posts is a major advantage of the proposed approach.
- Open Access
- 27 September 2023
- Published by Deu Muhendislik Fakultesi Fen ve Muhendislik in Dokuz Eylül Üniversitesi Mühendislik Fakültesi Fen ve Mühendislik Dergisi
- Vol. 25 (75) , 639-646
Akustik Işıma Kuvvetiyle Milimetre Boyutundaki Katı Parçacıkların Tuzaklanması ve Ayrıştırılması
Akustik ışıma kuvvetlerinden faydalanarak hava ortamında mm boyutundaki parçacıkların tuzaklanması ve manipülasyonu son zamanlarda yoğun ilgi gören çalışma alanlarından biridir. İki boyutlu fononik kristallerin çizgisel kusur durumları ile akustik ışıma kuvvetinden faydalanılarak havada mm boyutunda katı parçacıkların akustik metamalzeme mercekler ile manipülasyonu ve boyutlarına göre ayrıştırılması sayısal hesaplamalar ile gösterilmiştir. Bu yapılırken, Sonlu Elemanlar Yöntemiyle simülasyon hesabı yapılarak fononik kristallerin band yapıları elde edilmiştir. Çalışmada iki boyutlu fononik kristal ile oluşturulan bir dairesel halka çınlaçta yerçekimi ve akustik ışıma kuvvetlerinin birlikte etkisi ile küresel parçacıkların dairesel yörüngede hareketi sağlanmıştır. Hesaplamalarda 0.25 mm, 0.4 mm ve 0.55 mm çaplı polistiren küreciklerin hareketi t=0, 50, 100, 150, 200 ve 400 ms deki konumları incelenmeştir. Bütün parçacıklar dairesel düğüm çizgisini izleyerek belirtilen sürelerde yörüngenin yaklaşık olarak ¼, ½, ¾ ve 1 oranındaki kısımlarını kat etmişlerdir. t=400 ms anında 0.55 mm çaplı parçacık yaklaşık olarak iki turu tamamlarken, diğer parçacıklar sürüklenme kuvvetinden dolayı çizgisel hızlarını kaybetmekte ve düğüm çizgisinin en alt noktasında ayrışarak tuzaklanmaktadır.
- 27 September 2023
- Published by Deu Muhendislik Fakultesi Fen ve Muhendislik in Dokuz Eylül Üniversitesi Mühendislik Fakültesi Fen ve Mühendislik Dergisi
- Vol. 25 (75) , 639-646
Open AccessAkustik Işıma Kuvvetiyle Milimetre Boyutundaki Katı Parçacıkların Tuzaklanması ve Ayrıştırılması
Akustik ışıma kuvvetlerinden faydalanarak hava ortamında mm boyutundaki parçacıkların tuzaklanması ve manipülasyonu son zamanlarda yoğun ilgi gören çalışma alanlarından biridir. İki boyutlu fononik kristallerin çizgisel kusur durumları ile akustik ışıma kuvvetinden faydalanılarak havada mm boyutunda katı parçacıkların akustik metamalzeme mercekler ile manipülasyonu ve boyutlarına göre ayrıştırılması sayısal hesaplamalar ile gösterilmiştir. Bu yapılırken, Sonlu Elemanlar Yöntemiyle simülasyon hesabı yapılarak fononik kristallerin band yapıları elde edilmiştir. Çalışmada iki boyutlu fononik kristal ile oluşturulan bir dairesel halka çınlaçta yerçekimi ve akustik ışıma kuvvetlerinin birlikte etkisi ile küresel parçacıkların dairesel yörüngede hareketi sağlanmıştır. Hesaplamalarda 0.25 mm, 0.4 mm ve 0.55 mm çaplı polistiren küreciklerin hareketi t=0, 50, 100, 150, 200 ve 400 ms deki konumları incelenmeştir. Bütün parçacıklar dairesel düğüm çizgisini izleyerek belirtilen sürelerde yörüngenin yaklaşık olarak ¼, ½, ¾ ve 1 oranındaki kısımlarını kat etmişlerdir. t=400 ms anında 0.55 mm çaplı parçacık yaklaşık olarak iki turu tamamlarken, diğer parçacıklar sürüklenme kuvvetinden dolayı çizgisel hızlarını kaybetmekte ve düğüm çizgisinin en alt noktasında ayrışarak tuzaklanmaktadır.
- Open Access
- 28 August 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 123 (9)
Tunable acoustic resonances: From weak to strong coupling regime
Tunable interaction strength between a side-coupled ring resonator and an acoustic waveguide structure is demonstrated. Fano resonances in the weak coupling regime are observed from the interference between a discrete state of the ring resonator and a continuum state of the waveguide. As the distance between the two structures is decreased, a transition from weak to strong coupling regime is obtained, where we observe splitting in the transmission spectrum and Rabi oscillations in the temporal behavior for smaller values. The findings of the finite-element method simulations are supported with the results obtained from a simple theoretical model in which one can explain the dynamics of the hybrid modes. The results can contribute to device applications in acoustic sensors, switches, and surface acoustic wave integrated circuits.
- 28 August 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 123 (9)
Open AccessTunable acoustic resonances: From weak to strong coupling regime
Tunable interaction strength between a side-coupled ring resonator and an acoustic waveguide structure is demonstrated. Fano resonances in the weak coupling regime are observed from the interference between a discrete state of the ring resonator and a continuum state of the waveguide. As the distance between the two structures is decreased, a transition from weak to strong coupling regime is obtained, where we observe splitting in the transmission spectrum and Rabi oscillations in the temporal behavior for smaller values. The findings of the finite-element method simulations are supported with the results obtained from a simple theoretical model in which one can explain the dynamics of the hybrid modes. The results can contribute to device applications in acoustic sensors, switches, and surface acoustic wave integrated circuits.
- Open Access
- 9 November 2022
- Published by ASOS Yayinevi in European Journal of Science and Technology
- No. 41,p. 393-399
Liquid Sensor Based on Interaction between Decoupled Waveguides and a Cavity with Transverse Offset in a Phononic Crystal
A liquid sensor employing a cavity in the form of a point defect with a transverse offset along the normal bisector of a barrier at the center of a linear waveguide in a two-dimensional phononic crystal, which gives rise to two decoupled waveguides, is proposed. The phononic crystal consists of cylindrical steel rods with 2.0 mm radius in water, arranged with 4.2 mm lattice constant in the square lattice. Linear waveguides are formed by removing a single row from the phononic crystal, whereas the point defect is formed by substituting a single cylindrical steel rod by a polyethylene tubing comprising the analyte of interest. The cavity acts as a cross-bridge between the waveguides through the interaction of the linear defect mode in the input waveguide with the point defect mode, which in turn interacts with the output waveguide mode. Finite-element method simulations reveal that at frequencies around 200 kHz, a sharp peak with a quality factor of the order of 1000 occurs in the transmission spectrum of the system, where resonant transmission occurs. In case of determining the ratio of methanol in ethanol as an instance, it is found that the peak frequency exhibits a quadratic shift with the molar ratio of methanol. On the other hand, the transmission value decreases exponentially with increasing methanol ratio at the frequency of 196.19 kHz, which is the peak frequency for pure ethanol. The proposed sensing scheme can be utilized in many applications such as the identification of fake beverages and in high-throughput concentration measurements in the industry.
- 9 November 2022
- Published by ASOS Yayinevi in European Journal of Science and Technology
- No. 41,p. 393-399
Open AccessLiquid Sensor Based on Interaction between Decoupled Waveguides and a Cavity with Transverse Offset in a Phononic Crystal
A liquid sensor employing a cavity in the form of a point defect with a transverse offset along the normal bisector of a barrier at the center of a linear waveguide in a two-dimensional phononic crystal, which gives rise to two decoupled waveguides, is proposed. The phononic crystal consists of cylindrical steel rods with 2.0 mm radius in water, arranged with 4.2 mm lattice constant in the square lattice. Linear waveguides are formed by removing a single row from the phononic crystal, whereas the point defect is formed by substituting a single cylindrical steel rod by a polyethylene tubing comprising the analyte of interest. The cavity acts as a cross-bridge between the waveguides through the interaction of the linear defect mode in the input waveguide with the point defect mode, which in turn interacts with the output waveguide mode. Finite-element method simulations reveal that at frequencies around 200 kHz, a sharp peak with a quality factor of the order of 1000 occurs in the transmission spectrum of the system, where resonant transmission occurs. In case of determining the ratio of methanol in ethanol as an instance, it is found that the peak frequency exhibits a quadratic shift with the molar ratio of methanol. On the other hand, the transmission value decreases exponentially with increasing methanol ratio at the frequency of 196.19 kHz, which is the peak frequency for pure ethanol. The proposed sensing scheme can be utilized in many applications such as the identification of fake beverages and in high-throughput concentration measurements in the industry.
- 29 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 22 (15) , 14799-14805
An Acoustic Add-Drop Filter in a Phononic Crystal for High-Sensitivity Detection of Methanol in Ethanol in the Liquid Phase
An add-drop filter based on linear waveguides coupled through a ring resonator in a two-dimensional phononic crystal is introduced and its operation in detecting methanol concentration in ethanol is numerically investigated. The filter, which operates at around 200 kHz, has a small footprint of approximately 71.2 mm-by-84.0 mm, corresponding to 9.6-by-12.0 wavelengths. Band analyses of the phononic crystal and waveguide, as well as frequency domain simulations of filter operation for different methanol concentrations in the ring resonator cells are carried out through finite-element method. When the ring resonator cells are filled with pure ethanol, the drop port output is maximized, whereas through and add port outputs are minimized at the resonance frequency of 212.3 kHz. The contrast ratio between the drop and through/add port outputs is close to 1.0 at this frequency. Although the speed of sound and density are close in the two materials, the sensitivity is calculated as 12.54 Hz/% in terms of molar fraction of methanol. The corresponding figure of merit, obtained by dividing the sensitivity by drop port output peak width, varies between approximately 4.0 and 5.0. Moreover, a linear shift in the drop port peak frequency as a function of methanol concentration is observed. The add-drop filter can be calibrated for concentration sensing in different binary liquid mixtures. Higher sensitivities can be expected when the contrast of acoustic parameters, i.e., speed of sound and density, are larger for the constituents of the mixture.
- 29 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 22 (15) , 14799-14805
An Acoustic Add-Drop Filter in a Phononic Crystal for High-Sensitivity Detection of Methanol in Ethanol in the Liquid Phase
An add-drop filter based on linear waveguides coupled through a ring resonator in a two-dimensional phononic crystal is introduced and its operation in detecting methanol concentration in ethanol is numerically investigated. The filter, which operates at around 200 kHz, has a small footprint of approximately 71.2 mm-by-84.0 mm, corresponding to 9.6-by-12.0 wavelengths. Band analyses of the phononic crystal and waveguide, as well as frequency domain simulations of filter operation for different methanol concentrations in the ring resonator cells are carried out through finite-element method. When the ring resonator cells are filled with pure ethanol, the drop port output is maximized, whereas through and add port outputs are minimized at the resonance frequency of 212.3 kHz. The contrast ratio between the drop and through/add port outputs is close to 1.0 at this frequency. Although the speed of sound and density are close in the two materials, the sensitivity is calculated as 12.54 Hz/% in terms of molar fraction of methanol. The corresponding figure of merit, obtained by dividing the sensitivity by drop port output peak width, varies between approximately 4.0 and 5.0. Moreover, a linear shift in the drop port peak frequency as a function of methanol concentration is observed. The add-drop filter can be calibrated for concentration sensing in different binary liquid mixtures. Higher sensitivities can be expected when the contrast of acoustic parameters, i.e., speed of sound and density, are larger for the constituents of the mixture.
- 3 January 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 120 (1) , 011902
Continuously tunable acoustic Fano resonance in side-coupled Helmholtz resonator array assisted by a surface phononic crystal
Fano-like asymmetric line shape in a side-coupled series Helmholtz resonator array-waveguide system is continuously tuned by means of a one-dimensional surface phononic crystal, whose dispersion is exploited to adjust the phase factor appearing in indirectly coupled resonators. Finite-element method simulations reveal that the quality factor of the transmission spectrum can reach values on the order of 107, which can be finetuned by varying either waveguide width or phononic crystal groove depth. The Fano line shape dip, which appears around 25 kHz, red-shifts linearly with respect to the waveguide width at a rate of 308 Hz/mm. The quality factor exhibits a two order of magnitude drop for 0.01 mm waveguide width detuning from the optimal value. In comparison, three orders of magnitude decrease are observed for the same variation from the optimal value of the surface phononic crystal groove depth. Fano-like line shape is preserved when thermo-viscous losses are taken into account, where tunability with geometrical factors is still possible. Fine-tuning of either the dip frequency or quality factor can be utilized in demanding applications such as measurement of distance and concentrations of fluid mixtures with ultra high sensitivity.
- 3 January 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 120 (1) , 011902
Continuously tunable acoustic Fano resonance in side-coupled Helmholtz resonator array assisted by a surface phononic crystal
Fano-like asymmetric line shape in a side-coupled series Helmholtz resonator array-waveguide system is continuously tuned by means of a one-dimensional surface phononic crystal, whose dispersion is exploited to adjust the phase factor appearing in indirectly coupled resonators. Finite-element method simulations reveal that the quality factor of the transmission spectrum can reach values on the order of 107, which can be finetuned by varying either waveguide width or phononic crystal groove depth. The Fano line shape dip, which appears around 25 kHz, red-shifts linearly with respect to the waveguide width at a rate of 308 Hz/mm. The quality factor exhibits a two order of magnitude drop for 0.01 mm waveguide width detuning from the optimal value. In comparison, three orders of magnitude decrease are observed for the same variation from the optimal value of the surface phononic crystal groove depth. Fano-like line shape is preserved when thermo-viscous losses are taken into account, where tunability with geometrical factors is still possible. Fine-tuning of either the dip frequency or quality factor can be utilized in demanding applications such as measurement of distance and concentrations of fluid mixtures with ultra high sensitivity.
- Open Access
- 7 December 2021
- Published by American Physical Society (APS) in Physical Review B
- Vol. 104 (23) , 235407
Fano enhancement of unlocalized nonlinear optical processes
Field localization boosts nonlinear optical processes at the hot spots of metal nanostructures. Fano resonances can further enhance these “local” processes taking place at the hot spots. However, in conventional nonlinear materials, the frequency conversion takes place along the entire crystal body. That is, the conversion process is “unlocalized.” The path interference (Fano resonance) schemes developed for localized processes become useless in such materials. Here, we develop Fano enhancement schemes for unlocalized nonlinear optical processes. We show that three-orders-of-magnitude Fano enhancement multiplies the enhancements achieved via field-trapping techniques, e.g., in epsilon-near-zero materials. We demonstrate the phenomenon both analytically and using numerical solutions of Maxwell's equations. The agreement between the two solutions is impressive. We observe that the interference scheme for unlocalized processes is richer than that for the local processes. The method can be employed for any kind of nonlinear optical conversion. Moreover, Fano enhancement can be continuously controlled by an applied voltage.
- 7 December 2021
- Published by American Physical Society (APS) in Physical Review B
- Vol. 104 (23) , 235407
Open AccessFano enhancement of unlocalized nonlinear optical processes
Field localization boosts nonlinear optical processes at the hot spots of metal nanostructures. Fano resonances can further enhance these “local” processes taking place at the hot spots. However, in conventional nonlinear materials, the frequency conversion takes place along the entire crystal body. That is, the conversion process is “unlocalized.” The path interference (Fano resonance) schemes developed for localized processes become useless in such materials. Here, we develop Fano enhancement schemes for unlocalized nonlinear optical processes. We show that three-orders-of-magnitude Fano enhancement multiplies the enhancements achieved via field-trapping techniques, e.g., in epsilon-near-zero materials. We demonstrate the phenomenon both analytically and using numerical solutions of Maxwell's equations. The agreement between the two solutions is impressive. We observe that the interference scheme for unlocalized processes is richer than that for the local processes. The method can be employed for any kind of nonlinear optical conversion. Moreover, Fano enhancement can be continuously controlled by an applied voltage.
- 1 December 2021
- Published by IOP Publishing in Physica Scripta
- Vol. 96 (12) , 125032
Determination of methanol concentration in ethanol in liquid phase by a phononic crystal Mach-Zehnder interferometer
A practical and portable ultrasonic interferometric sensor to detect methanol concentration in ethanol in the liquid phase is numerically investigated. For high-sensitivity operation, the sensor is designed as a Mach–Zehnder interferometer based on a linear-defect waveguide in a two-dimensional phononic crystal, which consists of square array of cylindrical steel rods in water. The waveguide core comprises polyethylene tubing, impedance-matched with water, filled with either pure ethanol or ethanol-methanol binary mixture, allowing fast replacement of the analyte. Band structure analyses through the finite-element method are carried out to obtain guiding modes at frequencies around 200 kHz. With 50 × 21 cells with 4.2 mm periodicity, the total sensor area is 210-by-88.2 millimeters, which can be significantly reduced by increasing the operating frequency to megahertz range. The interferometer is constructed via T junctions of the waveguide, which facilitates low-loss equal splitting and recollection of ultrasonic waves. Sample and reference wave paths are constructed by filling polyethylene tubing on the upper and lower halves of the interferometer with the ethanol-methanol mixture and pure ethanol, respectively. Frequency-domain finite-element method simulations reveal that the sensor output is characterized by several transmission peaks, one of which is centered at 203.35 kHz with a full-width at half-maximum of 20 Hz, resulting in a quality factor of 10167. The peak frequency of this peak redshifts at a rate of 7.24 Hz per percent volume fraction change in methanol. The peak shift is linear when the methanol volume fraction is below 10%. Besides, the interferometric sensor has a figure of merit around 0.35. The proposed ultrasonic sensor offers rapid detection of methanol content in ethanol with high sensitivity.
- 1 December 2021
- Published by IOP Publishing in Physica Scripta
- Vol. 96 (12) , 125032
Determination of methanol concentration in ethanol in liquid phase by a phononic crystal Mach-Zehnder interferometer
A practical and portable ultrasonic interferometric sensor to detect methanol concentration in ethanol in the liquid phase is numerically investigated. For high-sensitivity operation, the sensor is designed as a Mach–Zehnder interferometer based on a linear-defect waveguide in a two-dimensional phononic crystal, which consists of square array of cylindrical steel rods in water. The waveguide core comprises polyethylene tubing, impedance-matched with water, filled with either pure ethanol or ethanol-methanol binary mixture, allowing fast replacement of the analyte. Band structure analyses through the finite-element method are carried out to obtain guiding modes at frequencies around 200 kHz. With 50 × 21 cells with 4.2 mm periodicity, the total sensor area is 210-by-88.2 millimeters, which can be significantly reduced by increasing the operating frequency to megahertz range. The interferometer is constructed via T junctions of the waveguide, which facilitates low-loss equal splitting and recollection of ultrasonic waves. Sample and reference wave paths are constructed by filling polyethylene tubing on the upper and lower halves of the interferometer with the ethanol-methanol mixture and pure ethanol, respectively. Frequency-domain finite-element method simulations reveal that the sensor output is characterized by several transmission peaks, one of which is centered at 203.35 kHz with a full-width at half-maximum of 20 Hz, resulting in a quality factor of 10167. The peak frequency of this peak redshifts at a rate of 7.24 Hz per percent volume fraction change in methanol. The peak shift is linear when the methanol volume fraction is below 10%. Besides, the interferometric sensor has a figure of merit around 0.35. The proposed ultrasonic sensor offers rapid detection of methanol content in ethanol with high sensitivity.