Egemen Teomete
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Egemen Teomete has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
Erman Demircilioğlu
2 shared publications- Jale Yanik
Faculty of Science, Department of Chemistry, Ege University, Izmir, Turkey
2 shared publications Mehmet Sisman
2 shared publications- Dheya M. A. Ghilan
Dokuz Eylul University, The Graduate School of Natural and Applied Sciences, Kaynaklar, Izmir, Turke
1 shared publication - Engin Aktaş
Izmir Institute of Technology Gülbahçe Campus, Izmir Institute of Technology
1 shared publication - Erik Schlangen
Faculty of Civil Engineering & Geosciences – Section of Materials & Environment, Delft University of Technology
1 shared publication
Latest Publications
- 28 January 2024
- Published by Elsevier in Construction and Building Materials
- Vol. 416
The effect of nano-biochar produced from various raw materials on flow and mechanical properties of mortar
- 28 January 2024
- Published by Elsevier in Construction and Building Materials
- Vol. 416
The effect of nano-biochar produced from various raw materials on flow and mechanical properties of mortar
- 6 June 2023
- Published by Fundacja Cement Wapno Beton in Cement Wapno Beton
- Vol. 28 (1) , 2-15
The effects of apricot kernel shell nanobiochar on mechanical properties of cement composites
Valorization of agricultural wastes is important both economically and environmentally. This study aimed to investigate the use of biochar as a filler to improve the mechanical properties of mortar and to help sequestrate CO2. The biochar was produced by pyrolysis of apricot kernel shell at 500 °C. Nanobiochar particles with dimensions less than 500 nm were obtained by high-energy ball milling process. Scanning electron microscope was used for determining the morphology of nanobiochar. The nanobiochar at different volume percentages [0.00-0.04-0.06-0.08-0.12-0.15%] was added to mortar. The mortar was casted into 40x40x160 mm molds. After water curing at 20°C for 28 days, compressive strength and flexural strength tests were performed. The mixture containing 0.04% nanobiochar by volume had an increase in flexural and compressive strengths by 5% and 15% respectively, while its fracture energies for flexure and compression increased by 98% and 38% respectively compared to the reference mortar. Furthermore, the mixture having 0.12% volume had an increase in flexural and compressive strengths by 32% and 11%, respectively, while the increase in fracture energies for flexure and compression was 52% and 25%, respectively, compared to the reference mortar. The mechanisms of nanobiochar effect on flow, strength, and fracture energy were enlightened. The nanobiochars bridge the cracks, divert the cracks, act as hydration nucleation sites, enhance the matrix by its porous structure, and developed internal curing that led to increase in strength and fracture energy. This study suggests that the biochar produced from the apricot kernel shell has the potential to be used as a carbon sequestering mixture to improve performance of mortar and thereby utilizing waste as a construction material, contributing to the economy and environment.
- 6 June 2023
- Published by Fundacja Cement Wapno Beton in Cement Wapno Beton
- Vol. 28 (1) , 2-15
The effects of apricot kernel shell nanobiochar on mechanical properties of cement composites
Valorization of agricultural wastes is important both economically and environmentally. This study aimed to investigate the use of biochar as a filler to improve the mechanical properties of mortar and to help sequestrate CO2. The biochar was produced by pyrolysis of apricot kernel shell at 500 °C. Nanobiochar particles with dimensions less than 500 nm were obtained by high-energy ball milling process. Scanning electron microscope was used for determining the morphology of nanobiochar. The nanobiochar at different volume percentages [0.00-0.04-0.06-0.08-0.12-0.15%] was added to mortar. The mortar was casted into 40x40x160 mm molds. After water curing at 20°C for 28 days, compressive strength and flexural strength tests were performed. The mixture containing 0.04% nanobiochar by volume had an increase in flexural and compressive strengths by 5% and 15% respectively, while its fracture energies for flexure and compression increased by 98% and 38% respectively compared to the reference mortar. Furthermore, the mixture having 0.12% volume had an increase in flexural and compressive strengths by 32% and 11%, respectively, while the increase in fracture energies for flexure and compression was 52% and 25%, respectively, compared to the reference mortar. The mechanisms of nanobiochar effect on flow, strength, and fracture energy were enlightened. The nanobiochars bridge the cracks, divert the cracks, act as hydration nucleation sites, enhance the matrix by its porous structure, and developed internal curing that led to increase in strength and fracture energy. This study suggests that the biochar produced from the apricot kernel shell has the potential to be used as a carbon sequestering mixture to improve performance of mortar and thereby utilizing waste as a construction material, contributing to the economy and environment.
- 1 January 2022
- Published by Teknik Dergi in Teknik Dergi
- Vol. 33 (1) , 11507-11519
The Strain Sensitivity of Coal Reinforced Smart Concrete by Piezoresistive Effect
The structures are challenged by earthquakes, material degradations and other environmental factors. In order to protect the lives, assets, and for maintenance planning, structural health monitoring (SHM) is important. In SHM applications, strain gages are widely used which have low durability, low sensitivity while they have high cost. To monitor a structure, large number of strain gages have to be used that increases the cost. In this study, seven coal reinforced concrete mixtures with 0, 0.35, 0.5, 0.8, 1, 1.5 and 2 volume % of coal were designed; three cubic samples for each mixture were fabricated. Simultaneous strain and electrical resistance measurement of the samples during the compression test was conducted. A strong linear piezoresistive relationship between strain and electrical resistance change with a correlation coefficient of 0.99 was determined. The concrete mixture having 0.8 volume % coal had the highest strain sensitivity of K=44, which was 22 times the strain sensitivity of commercial metal strain gages while it had a linearity error of LE=6.9% that was low. This mixture with 0.8 volume % coal is a candidate to be smart concrete which can sense its strain. As a contribution to the literature, a phenomenological model for the relationship between gage factor and coal volume % was explained in details. The multifunctional smart concrete will be used as a smart material, which can sense its strain in SHM applications while acting as a load bearing material.
- 1 January 2022
- Published by Teknik Dergi in Teknik Dergi
- Vol. 33 (1) , 11507-11519
The Strain Sensitivity of Coal Reinforced Smart Concrete by Piezoresistive Effect
The structures are challenged by earthquakes, material degradations and other environmental factors. In order to protect the lives, assets, and for maintenance planning, structural health monitoring (SHM) is important. In SHM applications, strain gages are widely used which have low durability, low sensitivity while they have high cost. To monitor a structure, large number of strain gages have to be used that increases the cost. In this study, seven coal reinforced concrete mixtures with 0, 0.35, 0.5, 0.8, 1, 1.5 and 2 volume % of coal were designed; three cubic samples for each mixture were fabricated. Simultaneous strain and electrical resistance measurement of the samples during the compression test was conducted. A strong linear piezoresistive relationship between strain and electrical resistance change with a correlation coefficient of 0.99 was determined. The concrete mixture having 0.8 volume % coal had the highest strain sensitivity of K=44, which was 22 times the strain sensitivity of commercial metal strain gages while it had a linearity error of LE=6.9% that was low. This mixture with 0.8 volume % coal is a candidate to be smart concrete which can sense its strain. As a contribution to the literature, a phenomenological model for the relationship between gage factor and coal volume % was explained in details. The multifunctional smart concrete will be used as a smart material, which can sense its strain in SHM applications while acting as a load bearing material.
- 18 November 2019
- Published by SAGE Publications in Journal of Intelligent Material Systems and Structures
- Vol. 31 (1) , 127-136
Strain sensitivity of steel-fiber-reinforced industrial smart concrete
Self-sensing cementitious composites can enable structures that are capable of carrying the loads applied on them while monitoring their condition. Most of earlier research has focused on the incorporation of nanofillers or microfibers into cement paste or mortar composites. However, there have been very limited number of studies on the development of steel-fiber-reinforced cementitious composites with self-sensing capabilities. This study explores strain sensitivity of concrete mixtures that include coarse aggregates up to 15 mm diameter and steel fibers with a length of 13 mm and a diameter of 0.25 mm. Five different concrete mixtures with steel fibers at 0%, 0.2%, 0.35%, 0.5%, and 0.8% volume ratios were fabricated. Compression tests with simultaneous measurement of strain and electrical resistance were conducted on the cubic specimens. Gauge factor and percent linearity that is a measure of error in strain sensing were calculated. Concrete mixtures with 0.5% steel fibers possess a strong linear relationship between applied strain and electrical resistance change with a gauge factor over 20 times larger than that of traditional metal strain gauges. Phenomenological models for different resistivity and gauge factors of cement paste/mortar with respect to concrete with large aggregates and short–long fiber cement composites were presented.
- 18 November 2019
- Published by SAGE Publications in Journal of Intelligent Material Systems and Structures
- Vol. 31 (1) , 127-136
Strain sensitivity of steel-fiber-reinforced industrial smart concrete
Self-sensing cementitious composites can enable structures that are capable of carrying the loads applied on them while monitoring their condition. Most of earlier research has focused on the incorporation of nanofillers or microfibers into cement paste or mortar composites. However, there have been very limited number of studies on the development of steel-fiber-reinforced cementitious composites with self-sensing capabilities. This study explores strain sensitivity of concrete mixtures that include coarse aggregates up to 15 mm diameter and steel fibers with a length of 13 mm and a diameter of 0.25 mm. Five different concrete mixtures with steel fibers at 0%, 0.2%, 0.35%, 0.5%, and 0.8% volume ratios were fabricated. Compression tests with simultaneous measurement of strain and electrical resistance were conducted on the cubic specimens. Gauge factor and percent linearity that is a measure of error in strain sensing were calculated. Concrete mixtures with 0.5% steel fibers possess a strong linear relationship between applied strain and electrical resistance change with a gauge factor over 20 times larger than that of traditional metal strain gauges. Phenomenological models for different resistivity and gauge factors of cement paste/mortar with respect to concrete with large aggregates and short–long fiber cement composites were presented.
- 1 November 2019
- Published by Elsevier in Construction and Building Materials
- Vol. 224, 420-427
Temperature and moisture effects on electrical resistance and strain sensitivity of smart concrete
- 1 November 2019
- Published by Elsevier in Construction and Building Materials
- Vol. 224, 420-427
Temperature and moisture effects on electrical resistance and strain sensitivity of smart concrete
- 1 January 2019
- Published by Fundacja Cement Wapno Beton in Cement Wapno Beton
- Vol. 24 (1) , 21-32
Photocatalytic gypsum plasters – studies of air cleaning properties and selected technical parameters
This study aims to investigate the feasibility of using industrial waste plastics, polypropylene (PP), polyethylene (PE) and polyamide (PA), obtained from recycling factory, as reinforcement for mortar. As one of the main problems of using waste plastics in cementitious composites is the...
- 1 January 2019
- Published by Fundacja Cement Wapno Beton in Cement Wapno Beton
- Vol. 24 (1) , 21-32
Photocatalytic gypsum plasters – studies of air cleaning properties and selected technical parameters
This study aims to investigate the feasibility of using industrial waste plastics, polypropylene (PP), polyethylene (PE) and polyamide (PA), obtained from recycling factory, as reinforcement for mortar. As one of the main problems of using waste plastics in cementitious composites is the...
- 10 June 2016
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 25 (7)
The effect of temperature and moisture on electrical resistance, strain sensitivity and crack sensitivity of steel fiber reinforced smart cement composite
Earthquakes, material degradations and other environmental factors necessitate structural health monitoring (SHM). Metal foil strain gages used for SHM have low durability and low sensitivity. These factors motivated researchers to work on cement based strain sensors. In this study, the effects of temperature and moisture on electrical resistance, compressive and tensile strain gage factors (strain sensitivity) and crack sensitivity were determined for steel fiber reinforced cement based composite. A rapid increase of electrical resistance at 200 °C was observed due to damage occurring between cement paste, aggregates and steel fibers. The moisture—electrical resistance relationship was investigated. The specimens taken out of the cure were saturated with water and had a moisture content of 9.49%. The minimum electrical resistance was obtained at 9% moisture at which fiber–fiber and fiber–matrix contact was maximum and the water in micro voids was acting as an electrolyte, conducting electrons. The variation of compressive and tensile strain gage factors (strain sensitivities) and crack sensitivity were investigated by conducting compression, split tensile and notched bending tests with different moisture contents. The highest gage factor for the compression test was obtained at optimal moisture content, at which electrical resistance was minimum. The tensile strain gage factor for split tensile test and crack sensitivity increased by decreasing moisture content. The mechanisms between moisture content, electrical resistance, gage factors and crack sensitivity were elucidated. The relations of moisture content with electrical resistance, gage factors and crack sensitivities have been presented for the first time in this study for steel fiber reinforced cement based composites. The results are important for the development of self sensing cement based smart materials.
- 10 June 2016
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 25 (7)
The effect of temperature and moisture on electrical resistance, strain sensitivity and crack sensitivity of steel fiber reinforced smart cement composite
Earthquakes, material degradations and other environmental factors necessitate structural health monitoring (SHM). Metal foil strain gages used for SHM have low durability and low sensitivity. These factors motivated researchers to work on cement based strain sensors. In this study, the effects of temperature and moisture on electrical resistance, compressive and tensile strain gage factors (strain sensitivity) and crack sensitivity were determined for steel fiber reinforced cement based composite. A rapid increase of electrical resistance at 200 °C was observed due to damage occurring between cement paste, aggregates and steel fibers. The moisture—electrical resistance relationship was investigated. The specimens taken out of the cure were saturated with water and had a moisture content of 9.49%. The minimum electrical resistance was obtained at 9% moisture at which fiber–fiber and fiber–matrix contact was maximum and the water in micro voids was acting as an electrolyte, conducting electrons. The variation of compressive and tensile strain gage factors (strain sensitivities) and crack sensitivity were investigated by conducting compression, split tensile and notched bending tests with different moisture contents. The highest gage factor for the compression test was obtained at optimal moisture content, at which electrical resistance was minimum. The tensile strain gage factor for split tensile test and crack sensitivity increased by decreasing moisture content. The mechanisms between moisture content, electrical resistance, gage factors and crack sensitivity were elucidated. The relations of moisture content with electrical resistance, gage factors and crack sensitivities have been presented for the first time in this study for steel fiber reinforced cement based composites. The results are important for the development of self sensing cement based smart materials.
- 1 October 2015
- Published by Elsevier in Measurement
- Vol. 74, 21-30
Measurement of crack length sensitivity and strain gage factor of carbon fiber reinforced cement matrix composites
- 1 October 2015
- Published by Elsevier in Measurement
- Vol. 74, 21-30
Measurement of crack length sensitivity and strain gage factor of carbon fiber reinforced cement matrix composites