MJMohd Jumain Jalil

Mohd Jumain Jalil

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mohd Jumain Jalil has a total of 133 co-authors. Here are the top co-authors by number of shared publications:

  • Intan Suhada Azmi

    Faculty of Chemical Engineering Studies Universiti Teknologi MARA, Cawangan Johor, Kampus Pasir Gudang Sri Alam Malaysia

    49 shared publications
  • Intan Suhada Azmi

    Universiti Teknologi Mara, Kampus Pasir Gudang

    18 shared publications
  • Mohammad Aathif Addli

    Faculty of Chemical Engineering Universiti Teknologi MARA (UiTM) Johor Branch, Pasir Gudang Campus Malaysia

    10 shared publications
  • Danial Nuruddin Azlan Raofuddin

    Universiti Teknologi MARA

    8 shared publications
  • Mohd Zulkipli Ab Kadir

    Faculty of Chemical Engineering Universiti Teknologi MARA, Cawangan Johor, Kampus Pasir Gudang Sri Alam Malaysia

    7 shared publications
  • Norin Hafizah Rahim

    Faculty of Chemical Engineering , 54703 Universiti Teknologi MARA , Cawangan Johor, Kampus Pasir Gudang, 81750 , Masai Johor , Malaysia

    7 shared publications

Latest Publications

  • Thermal behavior of banana pseudostem–wood dust hybrid particleboards bonded with phenol–formaldehyde resin

    by Mohd Azril Riduan, Mohanad El‐Harbawi, Mohd Jumain Jalil

    This study evaluates the thermal behavior of phenol–formaldehyde (PF)‐bonded banana pseudostem–wood dust (BPS–WD) hybrid particleboards. Boards with BPS:WD ratios of 100:0, 70:30, and 50:50 were fabricated at a target density of 0.50 g cm − 3, a nominal size of 340 mm × 340 mm × 25 mm, a fixed PF loading of 5 wt% on a dry‐particle basis, and a hot‐press temperature of 181°C. Thermogravimetric analysis (TGA) was used to compare mass‐loss behavior up to approximately 800°C and final residue, while differential scanning calorimetry (DSC) was used for comparative interpretation of the retained heat‐flow curves. All formulations showed an initial mass loss below approximately 100°C, followed by the principal lignocellulosic degradation region and slower high‐temperature decomposition. The 100:0 formulation produced the highest final residual mass (12.72%), followed by 70:30 (6.03%) and 50:50 (1.42%). The remaining residue may include both carbonaceous char and inorganic mineral ash; therefore, residual mass was not interpreted as a direct ranking of overall board quality. The DSC profiles also differed among the formulations, demonstrating that the BPS:WD ratio affected heat‐flow response. These findings establish a focused thermal comparison of PF‐bonded BPS–WD particleboards and provide a basis for future work using fully recorded quantitative thermal‐transition parameters.

  • Catalytic Epoxidation of Castor Oil Using Sulfate‐Impregnated ZSM ‐5 for Enhanced Oxirane Formation

    by Mohammad Aathif Addli, Maher M. Alrashed, Mohd Jumain Jalil

    This study investigates the reaction kinetics of castor oil epoxidation using sulfate‐impregnated ZSM‐5 as a heterogeneous catalyst, focusing on the effects of sulfuric acid concentration, impregnation temperature, and calcination temperature. Unlike most seed oils, castor oil is predominantly composed of ricinoleic acid‐rich triglycerides, which contain both an epoxidizable carbon–carbon double bond and a native hydroxyl group, providing a uniquely functional feedstock for producing hydroxyl‐bearing epoxides. A series of catalysts were synthesized via wet impregnation at varying temperatures (25°C, 45°C, and 65°C) and treated with different concentrations of sulfuric acid (0.3, 0.6, and 0.9 M), followed by calcination at 350°C, 450°C, and 550°C. The kinetics of the epoxidation reaction were studied using a pseudo‐first‐order model and validated through MATLAB‐based numerical modeling coupled with Simulated Annealing optimization. The optimal impregnation temperature was 25°C, achieving a rate constant of 0.014 min −1 and a conversion value, ln[1/(1 − X )], of 0.39. Despite a slightly higher coefficient of determination ( R 2 = 0.9958) at 45°C, the overall conversion was lower. The highest reaction rate ( k = 0.033 min −1 ) was observed at a sulfuric acid concentration of 0.6 M; however, the catalyst prepared using 0.3 M sulfuric acid exhibited the highest conversion, indicating better catalyst stability and performance. Regarding calcination, although 450°C yielded the fastest reaction ( k = 0.016 min −1 ), the highest conversion was recorded at 550°C, with an ln[1/(1 − X )] value of 0.41. MATLAB modeling further validated the system, demonstrating a strong correlation ( R 2 = 0.9447), with kinetic constants of k 1 = 0.0236, k 2 = 0.00293, k 3 = 0.01006, and k 4 = 0.0474 that adequately represented the experimental behavior. The concentration profiles confirmed the sequential conversion of reactants into intermediates and products. This study provides critical insights into the preparation–structure–performance relationship of sulfate‐impregnated ZSM‐5 catalysts for sustainable epoxidation processes.

  • Activated Carbon‐Supported Molybdenum Oxide Catalysts for Epoxidation of Palm Oleic Acid

    by Aishah Derahman, Mohd Jumain Jalil, Mohd Saufi Md Zaini

    Palm oleic acid (POA) epoxidation offers a route for producing bio‐based epoxide intermediates for polymer additives, coatings, and biolubricants. This study evaluated the suitability of activated carbon (AC) as a support for molybdenum (Mo) oxide species and examined the influence of Mo loading on the catalyst structure and the relative conversion to oxirane (RCO) during POA epoxidation. AC‐supported Mo catalysts with nominal metal loadings of 5–20 wt.% were prepared by wet impregnation using ammonium molybdate tetrahydrate (AMT) as metal precursor. The characterization results confirmed that Mo incorporation increased with increasing nominal loading, while x‐ray diffraction (XRD) indicated the presence of MoO x species, with more pronounced Mo oxide‐related reflections at higher loadings. Textural analysis revealed a reduction in the surface area and pore volume after Mo incorporation, suggesting partial pore occupation by Mo‐containing species. Among the supported catalysts, Mo/AC‐15 exhibited the highest RCO, reaching approximately 50% after 4 h at 70°C. Fourier‐transform infrared spectroscopy (FTIR) and 1 H Nuclear Magnetic Resonance ( 1 H NMR) analyses supported oxirane formation, as evidenced by the appearance of C─O─C absorption bands, reduction of olefinic bands and proton signals, and the emergence of new oxirane‐related proton signals.

  • High‐solid epoxy coatings incorporating propylene glycol monomethyl ether as a safer alternative to xylene

    by Noorfazlida Mohamed, Izni Mariah Ibrahim, Mohd Jumain Jalil

    High‐solid epoxy coatings have gained increasing attention as environmentally responsible protective coatings because their high solids content can reduce solvent requirements while maintaining good mechanical and corrosion protection properties. This study evaluates the effect of replacing xylene with propylene glycol monomethyl ether (PM) in high‐solid epoxy coatings, with particular emphasis on corrosion performance and volatile organic compound (VOC) composition. Corrosion resistance was evaluated using Linear Polarization Resistance (LPR) and weight‐loss measurements. The PM‐based coating exhibited higher corrosion rates than the xylene‐based coating, with values of 2.85 × 10 −5 and 8.71 mpy compared with 1.36 × 10 −5 and 2.18 mpy, respectively. Nevertheless, both systems exhibited high corrosion inhibition performance under the test conditions. VOC analysis showed that the xylene‐based formulation contained detectable ethylbenzene and xylene isomers, whereas these aromatic compounds were not detected in the PM‐based formulation. Instead, 1‐methoxy‐2‐propanol was the major identified solvent component in the PM formulation. Although the total measured VOC content increased from 99.15 g/L for the xylene formulation to 120.66 g/L for the PM formulation, the substitution of detectable aromatic hydrocarbons with an oxygenated solvent substantially changed the VOC composition. The novelty of this study lies in demonstrating that PM substitution can modify the VOC hazard profile of a high‐solid epoxy coating while maintaining substantial corrosion protection.

  • Low‐temperature epoxidation of hybrid rice bran oil and oleic acid using natural zeolite catalyst

    by Intan Suhada Azmi, Azmi Mohd Noor, Muhammad Nazmi Amsyar Azrul, Nor Fadilah Mohamad, Aishath Shaira, Mohd Jumain Jalil

    This study investigates the low‐temperature epoxidation of a hybrid rice bran oil–oleic acid system using natural zeolite as a heterogeneous catalyst. The reaction was performed within the temperature range of 30–60°C, and its performance was evaluated based on relative conversion to oxirane (RCO), oxirane oxygen content (OOC), FTIR analysis, and kinetic modeling. The results show that the maximum RCO of 23.10% was achieved at 60°C, while a more stable RCO profile was obtained at 50°C with a peak value of 16.64%. At lower temperatures, RCO values remained limited, with 8.54% and 8.60% recorded at 30°C and 40°C, respectively. For oxygen carrier type, formic acid exhibited the highest RCO of 42.70%, followed by acetic acid (42.01%) and lactic acid (25.20%). The temporal profile of OOC showed a maximum experimental value of 0.9277 at 20 min before gradually declining. FTIR spectra confirmed the formation of epoxy groups with a characteristic absorption peak at ~825 cm −1 . Kinetic modeling using particle swarm optimization demonstrated good agreement between experimental and simulated data, with a low error value of 0.12. The results confirm the effectiveness of low‐temperature epoxidation using natural zeolite for producing bio‐based epoxide intermediates.

  • Epoxidation of Waste Palm Cooking Applied With Hybrid Zeolite Catalyst Derived From Natural Clinoptilolite/Synthetic ZSM ‐5

    by Nurul Huda M. Ali, Swee Pin Yeap, Mohd Jumain Jalil

    Catalyst development for epoxidation is constrained by the trade‐off between efficiency, cost, and sustainability. Homogeneous catalysts such as sulfuric, hydrochloric, and acetic acids exhibit high activity but are limited by corrosiveness, environmental concerns, and low selectivity. Alternatively, heterogenous catalyst of natural zeolites offer a sustainable alternative due to their abundance, recyclability and low cost, however; it is suffering from intrinsic variability, resulting in inconsistent of performance. On the other hand, synthetic zeolites provide high surface area and stability, but their high production cost restricts practical application. To address this gap, a novel hybrid zeolite catalyst was synthesized by integrating natural clinoptilolite with synthetic ZSM‐5 via an impregnation method. The optimal conditions for synthesis catalyst was natural‐to‐synthetic mass ratio of 0.5:1.0, 0.5 M HCl solution, and calcination temperature at 550°C. SEM analysis confirmed the successful formation of the hybrid catalyst, exhibiting a well‐defined crystalline morphology with regular crystal shapes and smooth surfaces. FTIR analysis verified the successful epoxidation of waste palm cooking oil through the enhanced intensity of the characteristic oxirane absorption band at 852 cm −1 . Despite a 15.82% reduction in specific surface area, hybrid zeolite catalyst achieved RCO yields comparable to synthetic ZSM‐5 catalyst which is 50.45% ± 1.74%. It is indicating that catalytic performance is governed not only by the specific surface area, but also by active‐site effectiveness and mass‐transfer characteristics. Physicochemical analyses further confirmed the superior epoxidation performance of the hybrid catalyst through the greatest reduction in iodine value and the corresponding increase in viscosity. Kinetic modeling using MATLAB, integrated with a Genetic Algorithm and the ODE45 solver, validated the superior catalytic performance of the hybrid system. The kinetic rate constants obtained were k 1 a = 1.9460 mol L −1 min −1 , k 1 b = 11.4667 mol L −1 min −1 , k 2 = 0.2265 mol L −1 min −1 , and k 3 = 0.0019 mol L −1 min −1 . These results highlight the effectiveness of the hybrid catalyst system and demonstrate its potential as a cost‐effective and sustainable catalyst design strategy.

  • Interfacial Synergy in ZSM ‐5/ TiO 2 Heterogeneous Catalysts for Enhanced Stability in Rubber Seed Oil Epoxidation

    by Norhafini Hambali, Mohd Jumain Jalil

    Catalytic epoxidation of vegetable oil commonly possesses a reduction of relative conversion to oxirane (RCO%) over reaction time due to the ring‐opening of epoxide groups that can be overcome by controlling pore structure and reactant diffusion control. This research was conducted to tailor heterogeneous catalyst composite surface area by combining ZSM‐5 with titanium dioxide (TiO 2 ) via impregnation method to improve the reaction stability of the catalyst in the epoxidation of rubber seed oil (RSO). Five different ratios of ZSM‐5 to TiO 2 were studied to observe the catalyst's efficacy in the epoxidation process by measuring the relative conversion to oxirane (RCO%), surface area (BET), and structural characteristics (XRD). The 1:3 ZSM‐5/TiO 2 ratio showed the most constant RCO% during the reaction (20 min) compared to single stage catalyst which RCO% inclined rapidly and decline afterwards, even though the epoxide yield was a little lower (below 15%). Next, the calcination conditions (temperature and time) of the catalyst were studied to improve the RCO%. Catalyst calcined at temperature of 300°C within 6 h produced the highest RCO% of 35% compared to initial RCO% of 15%, the lowest BET surface area and the biggest pore volume. XRD characterization showed that TiO 2 was successfully added to the ZSM‐5 framework without changing the way the crystals looked. The hybrid catalyst also maintained catalytic activity throughout the multi‐cycle evaluation, with all RCO values remaining comfortably above the 40% threshold. The combination of ZSM‐5's microporous structure and TiO 2 's reactive surface managed to suppress the ring‐opening of epoxide groups and maintained high RCO% at the longest period during the catalytic rubber seed oil epoxidation. This custom‐made composite is an effective alternative catalyst to improve quality of epoxide groups produced from vegetable oil epoxidation for making bio‐based materials and green polymers.

  • Sustainable epoxidation of red palm oil via in-situ peracid mechanism catalyzed by natural zeolite

    by Danial Nuruddin Azlan Raofuddin, Nur Azmina Asyiqin Norazmi, Mohd Jumain Jalil

    This study presents a sustainable approach for the epoxidation of red palm oil (RPO) using a natural zeolite catalyst via an in situ peracid mechanism. The process addresses the limitations of conventional homogeneous acid systems by reducing corrosive waste and improving catalyst recoverability while valorizing an underutilized palm fraction. The effects of temperature and hydrogen peroxide concentration on oxirane formation were evaluated through oxirane oxygen content (OOC) and relative conversion to oxirane (RCO). The optimum temperature of 65°C produced the highest RCO (≈25–30%) at the early reaction stage, while excessive oxidant and prolonged reaction time promoted oxirane ring opening. FTIR analysis confirmed the formation of epoxy groups, and kinetic modeling showed excellent agreement with experimental data (R 2 = 0.9778; Error = 0.0469). The synthesized epoxidized RPO demonstrates strong potential for application in bio-based polymer systems, including polyols for polyurethane production, plasticizers, coatings, and environmentally friendly resins, highlighting its relevance for sustainable industrial applications.

  • Prilezhaev Reaction of Vegetable Oil for Bio‐Based Polyol Production: A Review

    by Intan Suhada Azmi, Mohd Zulkipli Ab Kadir, Mohd Jumain Jalil

    This review paper examines the Prilezhaev reaction, commonly known as the epoxidation of vegetable oils, which are renewable resources with promising industrial applications. The epoxidation process involves reacting unsaturated fatty acids with peroxy acids to form epoxide groups, serving as essential intermediates for further chemical transformations. Specifically, this paper provides an overview of various epoxidation techniques and the subsequent production of bio‐polyols, highlighting current advancements, challenges, and alignment with green chemistry principles. Furthermore, the article evaluates ring‐opening reactions of epoxidized vegetable oils using diverse reagents. These reactions yield polyols, which are the key intermediates required for synthesizing polyurethanes and other polymers. Ultimately, transforming vegetable oils into functionalized bio‐based products via epoxidation and ring‐opening reactions offers broad industrial applications in fields such as bioplastics, lubricants, and coatings.

  • Overview of oleic acid epoxidation via the Prileschajew reaction and hydroxylation process

    by Danial Nuruddin Azlan Raofuddin, Hamzah Hafizuddin Habri, Mohd Jumain Jalil

    Oleic acid epoxidation via the Prileschajew reaction using peracid oxidation and subsequent hydroxylation with oleic acid has gained significant attention as a sustainable route for producing dihydroxystearic acid (DHSA) and polyols. In this process, the oxirane ring undergoes hydrolysis with water to yield DHSA, while alcoholysis with alcohol leads to polyol formation. This review provides a comprehensive overview of the epoxidation mechanism, emphasizing oxirane ring formation and its conversion into hydroxyl derivatives. Key factors affecting epoxidation efficiency and product yield, including reaction conditions, catalyst selection, and process optimization, are critically analyzed. The role of hydrolysis in DHSA formation and alcoholysis in polyol synthesis is also discussed. This process supports the growing demand for renewable alternatives to petrochemical‐based resources, offering advantages such as biodegradability and industrial versatility.