Cursino Brandao Jacobina
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Cursino Brandao Jacobina has a total of 100 co-authors. Here are the top co-authors by number of shared publications:
- Nady Rocha
Universidade Federal da Paraíba
20 shared publications - Nayara Brandao de Freitas
Siemens Energy, Erlangen, Germany
15 shared publications - Antonio Marcus Nogueira Lima
Department of Electrical Engineering, Federal University of Campina Grande, Campina Grande, Brazil
13 shared publications - Reuben Palmer Rezende de Sousa
Department of Electrical Engineering, Federal University of Campina Grande, Campina Grande, Brazil
13 shared publications - Alan Santana Felinto
State University of Paraíba image/svg+xml
12 shared publications - Mauricio Beltrao de Rossiter Correa
Electrical Engineering Department, Universidade Federal de Alagoas, Macei, Brazil
12 shared publications
Latest Publications
- Open Access
- 21 September 2026
- Published by Associacao Brasileira de Eletronica de Potencia SOBRAEP in Eletrônica de Potência
- Vol. 31, e202627
Transformerless Six-Leg Single-Phase to Split-Phase Power Converter with Grid Disturbance Mitigation
This article proposes a transformerless six-leg single-phase to two-phase AC-DC-AC converter for applications in single-phase three-wire distribution systems, also known as single split-phase systems. Featuring an architecture built upon a pair of three-leg converters, and employs space vector pulse-width modulation to synthesize the output voltages, this modulation scheme reduces harmonic content. Under severe load unbalances, the implemented control scheme successfully preserves fixed amplitude and frequency for the output voltages, while ensuring a predominantly fundamental grid current with low harmonic distortion and a high power factor, including when supplying nonlinear loads. In addition, the proposed topology can mitigate grid disturbances, such as voltage sags and swells, maintaining the load voltages with constant amplitude and frequency and preserving a high grid-side power factor under voltage disturbances, as well as nonlinear and unbalanced loads conditions. When contrasted with the conventional four-leg AC-DC-AC converter, the proposed converter mitigates grid current harmonic distortion while reducing semiconductor losses. The validity of the entire system are thoroughly confirmed through simulation and experimental evaluations.
- 21 September 2026
- Published by Associacao Brasileira de Eletronica de Potencia SOBRAEP in Eletrônica de Potência
- Vol. 31, e202627
Open AccessTransformerless Six-Leg Single-Phase to Split-Phase Power Converter with Grid Disturbance Mitigation
This article proposes a transformerless six-leg single-phase to two-phase AC-DC-AC converter for applications in single-phase three-wire distribution systems, also known as single split-phase systems. Featuring an architecture built upon a pair of three-leg converters, and employs space vector pulse-width modulation to synthesize the output voltages, this modulation scheme reduces harmonic content. Under severe load unbalances, the implemented control scheme successfully preserves fixed amplitude and frequency for the output voltages, while ensuring a predominantly fundamental grid current with low harmonic distortion and a high power factor, including when supplying nonlinear loads. In addition, the proposed topology can mitigate grid disturbances, such as voltage sags and swells, maintaining the load voltages with constant amplitude and frequency and preserving a high grid-side power factor under voltage disturbances, as well as nonlinear and unbalanced loads conditions. When contrasted with the conventional four-leg AC-DC-AC converter, the proposed converter mitigates grid current harmonic distortion while reducing semiconductor losses. The validity of the entire system are thoroughly confirmed through simulation and experimental evaluations.
- 27 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (6) , 9481-9492
Single-Phase Transformerless Unified Power Quality Conditioner Based on Three-Leg and Standby Converters
In this paper, a transformerless single-phase-to-single-phase unified power quality conditioner (UPQC) based on three-leg and standby converters is proposed. The system consists of a two-leg module series connected to a three-leg module. The proposed control system provides shunt and series compensation and can be designed to operate with a high modulation index under rated conditions and voltage sag events. In addition, a low standby power consumption and a new decoupling method to compensate voltage swells using the two-leg module are proposed. Compared to conventional solution, the proposed converter exhibits lower semiconductor losses and reduced waveform harmonic distortion, while maintaining equal or superior operational features, including voltage swell compensation capability and the elimination of circulating currents and line-frequency transformers. The system model, the scalar PWM technique, the applied standby concept, and the overall control system strategy are discussed. Simulations and experimental results are presented to evaluate the feasibility of the proposed system and the correctness of the design methodology.
- 27 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (6) , 9481-9492
Single-Phase Transformerless Unified Power Quality Conditioner Based on Three-Leg and Standby Converters
In this paper, a transformerless single-phase-to-single-phase unified power quality conditioner (UPQC) based on three-leg and standby converters is proposed. The system consists of a two-leg module series connected to a three-leg module. The proposed control system provides shunt and series compensation and can be designed to operate with a high modulation index under rated conditions and voltage sag events. In addition, a low standby power consumption and a new decoupling method to compensate voltage swells using the two-leg module are proposed. Compared to conventional solution, the proposed converter exhibits lower semiconductor losses and reduced waveform harmonic distortion, while maintaining equal or superior operational features, including voltage swell compensation capability and the elimination of circulating currents and line-frequency transformers. The system model, the scalar PWM technique, the applied standby concept, and the overall control system strategy are discussed. Simulations and experimental results are presented to evaluate the feasibility of the proposed system and the correctness of the design methodology.
- 8 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72 (8) , 7885-7896
Single-Phase Multilevel Cascaded Bridgeless PFC Rectifier
This article proposes a unidirectional single-phase multilevel cascaded rectifier suited for power factor correction applications. The proposed configuration is based on two traditional bridgeless rectifiers, so that it is possible to synthesize five input voltage levels. This arrangement allows a reduced number of fast diodes in its structure, offering low costs. This feature is achieved by ensuring the dc-link capacitor voltage equalization. Detailed descriptions of the operating modes, dc-link voltage equalization, pulse-width modulation (PWM) technique, and control strategy are provided. Simulation and experimental results are included to confirm feasibility.
- 8 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72 (8) , 7885-7896
Single-Phase Multilevel Cascaded Bridgeless PFC Rectifier
This article proposes a unidirectional single-phase multilevel cascaded rectifier suited for power factor correction applications. The proposed configuration is based on two traditional bridgeless rectifiers, so that it is possible to synthesize five input voltage levels. This arrangement allows a reduced number of fast diodes in its structure, offering low costs. This feature is achieved by ensuring the dc-link capacitor voltage equalization. Detailed descriptions of the operating modes, dc-link voltage equalization, pulse-width modulation (PWM) technique, and control strategy are provided. Simulation and experimental results are included to confirm feasibility.
- 16 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (1) , 472-486
Five-Leg Single-Phase Transformerless Unified Power Quality Conditioner
This paper proposes a transformerless single-phase unified power quality conditioner (UPQC) consisting of a threeleg converter and a hybrid shunt converter. The proposed system provides grid voltage compensation for both sags and swells while simultaneously maintaining a high grid-side power factor with low harmonic content. The system operates with a high modulation index during rated conditions and grid voltage sags. Compared to the conventional single-phase three-leg UPQC, the proposed configuration offers advantages regarding required semiconductor device ratings, harmonic distortion, and power losses. The paper presents the system model, a simplified carrierbased space vector pulse-width modulation scheme, operational constraints, and overall control strategies. Simulation and experimental results are addressed to validate the feasibility of the proposed system.
- 16 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (1) , 472-486
Five-Leg Single-Phase Transformerless Unified Power Quality Conditioner
This paper proposes a transformerless single-phase unified power quality conditioner (UPQC) consisting of a threeleg converter and a hybrid shunt converter. The proposed system provides grid voltage compensation for both sags and swells while simultaneously maintaining a high grid-side power factor with low harmonic content. The system operates with a high modulation index during rated conditions and grid voltage sags. Compared to the conventional single-phase three-leg UPQC, the proposed configuration offers advantages regarding required semiconductor device ratings, harmonic distortion, and power losses. The paper presents the system model, a simplified carrierbased space vector pulse-width modulation scheme, operational constraints, and overall control strategies. Simulation and experimental results are addressed to validate the feasibility of the proposed system.
- 27 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (1) , 395-405
Three-Phase Four-Wire Transformerless Unified Power Quality Conditioner Based on AC-DC-AC Nine-Leg Converter and Shunt Converter
In this paper, a three-phase transformerless unified power quality conditioner (UPQC) based on a nine-leg converter and a four-wire shunt converter is proposed and investigated. The system ensures grid power factor compensation with low harmonic content and feeds the load with a sinusoidal waveform. The shunt converter operates with a low switching frequency and provides balanced currents, which allows the nine-leg converter to operate with a wide range of unbalanced loads, while compensating for the harmonic content. In addition, the shared-leg currents are minimized, reducing the power losses. Compared with the conventional transformerless UPQCs, the proposed converter achieved lower overall semiconductor losses under a severely unbalanced load. Furthermore, it has also been able to reduce the size of DC-link capacitors when compared with conventional converters. The system model, pulse-width modulation (PWM) techniques, and control strategy are discussed in this work. Simulations and experimental results are presented to confirm the feasibility of the proposed structure and the correctness of the design methodology.
- 27 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (1) , 395-405
Three-Phase Four-Wire Transformerless Unified Power Quality Conditioner Based on AC-DC-AC Nine-Leg Converter and Shunt Converter
In this paper, a three-phase transformerless unified power quality conditioner (UPQC) based on a nine-leg converter and a four-wire shunt converter is proposed and investigated. The system ensures grid power factor compensation with low harmonic content and feeds the load with a sinusoidal waveform. The shunt converter operates with a low switching frequency and provides balanced currents, which allows the nine-leg converter to operate with a wide range of unbalanced loads, while compensating for the harmonic content. In addition, the shared-leg currents are minimized, reducing the power losses. Compared with the conventional transformerless UPQCs, the proposed converter achieved lower overall semiconductor losses under a severely unbalanced load. Furthermore, it has also been able to reduce the size of DC-link capacitors when compared with conventional converters. The system model, pulse-width modulation (PWM) techniques, and control strategy are discussed in this work. Simulations and experimental results are presented to confirm the feasibility of the proposed structure and the correctness of the design methodology.
- 19 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 60 (2) , 3373-3382
Asymmetric Cascaded Transformer Multilevel AC-DC Converter
This paper presents a multilevel single-phase rectifier with cascaded transformers and two dc links. The configuration is composed of $k$ cascaded transformers, which isolate the load from the power source, and $2(k+1)$ two-level (2L) legs, in which some insulated-gate bipolar transistor (IGBT) legs can be replaced by diode legs if the bidirectional operation is not required. The configurations have different turns and dclink voltage ratios, characterizing an asymmetric configuration. In addition, the second dc link is used to increase the number of voltage levels, which results in better input voltage quality. This dc link has a lower voltage and can be a floating capacitor. Furthermore, the nearest-level control (NLC) technique is used to generate voltage with high power quality. The proposed configurations are compared with conventional configurations. Finally, experimental results are shown to demonstrate the feasibility of the system.
- 19 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 60 (2) , 3373-3382
Asymmetric Cascaded Transformer Multilevel AC-DC Converter
This paper presents a multilevel single-phase rectifier with cascaded transformers and two dc links. The configuration is composed of $k$ cascaded transformers, which isolate the load from the power source, and $2(k+1)$ two-level (2L) legs, in which some insulated-gate bipolar transistor (IGBT) legs can be replaced by diode legs if the bidirectional operation is not required. The configurations have different turns and dclink voltage ratios, characterizing an asymmetric configuration. In addition, the second dc link is used to increase the number of voltage levels, which results in better input voltage quality. This dc link has a lower voltage and can be a floating capacitor. Furthermore, the nearest-level control (NLC) technique is used to generate voltage with high power quality. The proposed configurations are compared with conventional configurations. Finally, experimental results are shown to demonstrate the feasibility of the system.
- 24 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (1) , 885-897
Three-Phase Four-Wire Nine-Leg AC–DC–AC Converter Based on High-Frequency Link
This work proposes a three-phase four-wire ac–dc–ac converter composed of three single-phase three-leg cells with shared legs. Also, the three dc-links are connected employing a dc–dc converter with a high-frequency transformer (HFT). Each dc-link is connected to a high-frequency H-bridge and each H-bridge is connected to a winding of the transformer. The HFT is responsible to balance the dc-links, providing the necessary power flow. The proposed converter allows dealing with a wide range of unbalances, compensates for grid voltage sags, and provides a high power factor on the grid side with low harmonic content. In addition, the proposed structure can operate with minimum dc-link voltage values in applications where the grid and load frequencies are the same, such as unified power quality conditioners. Converter model is provided, as well as pulse-width modulation, control strategy, design of passive devices, and power analysis. Experimental results are presented for validation purposes. Compared with conventional solutions, the proposed converter offers advantages, such as not requiring line-frequency transformers, being able to operate under severe unbalanced conditions, or requiring a simpler structure.
- 24 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (1) , 885-897
Three-Phase Four-Wire Nine-Leg AC–DC–AC Converter Based on High-Frequency Link
This work proposes a three-phase four-wire ac–dc–ac converter composed of three single-phase three-leg cells with shared legs. Also, the three dc-links are connected employing a dc–dc converter with a high-frequency transformer (HFT). Each dc-link is connected to a high-frequency H-bridge and each H-bridge is connected to a winding of the transformer. The HFT is responsible to balance the dc-links, providing the necessary power flow. The proposed converter allows dealing with a wide range of unbalances, compensates for grid voltage sags, and provides a high power factor on the grid side with low harmonic content. In addition, the proposed structure can operate with minimum dc-link voltage values in applications where the grid and load frequencies are the same, such as unified power quality conditioners. Converter model is provided, as well as pulse-width modulation, control strategy, design of passive devices, and power analysis. Experimental results are presented for validation purposes. Compared with conventional solutions, the proposed converter offers advantages, such as not requiring line-frequency transformers, being able to operate under severe unbalanced conditions, or requiring a simpler structure.
- 24 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 59 (6) , 6941-6951
Four-Wire Active Power Filter Based on Asymmetric Cascaded H-Bridges
This paper studies a four-wire active power filter composed of three H-bridges, a four-wire three-phase converter, and four dc-links. The first three dc-links with the same voltage values, and the other assumes twice or half voltage. These asymmetrical conditions (dc-link voltage ratio 1:2 and 2:1) and adding a fourth interface inductor are investigated. These aspects affect the minimum dc-link voltage required, quality of waveforms, and compensation capacity. A new control strategy of the dc-links voltages that reduces its voltage ripple is presented in this paper. The circuit model, level-shifted PWM strategy, simulation and experimental results, and comparisons in terms of efficiency, ratings of power switches and quality of waveforms are also addressed.
- 24 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 59 (6) , 6941-6951
Four-Wire Active Power Filter Based on Asymmetric Cascaded H-Bridges
This paper studies a four-wire active power filter composed of three H-bridges, a four-wire three-phase converter, and four dc-links. The first three dc-links with the same voltage values, and the other assumes twice or half voltage. These asymmetrical conditions (dc-link voltage ratio 1:2 and 2:1) and adding a fourth interface inductor are investigated. These aspects affect the minimum dc-link voltage required, quality of waveforms, and compensation capacity. A new control strategy of the dc-links voltages that reduces its voltage ripple is presented in this paper. The circuit model, level-shifted PWM strategy, simulation and experimental results, and comparisons in terms of efficiency, ratings of power switches and quality of waveforms are also addressed.
- 6 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 59 (6) , 6876-6888
PUC Converter Based on AC-DC-AC Multilevel Topologies With a Shared Leg
In this paper, a single-phase ac-dc-ac multilevel configuration based on packed u-cell (PUC) is investigated. The system consists of a four-leg module with a u-cell connected to the shared part of the system and a low-frequency transformer at the grid side. The proposed converter allows one to compensate for grid voltage sags and swells, and to provide a high power factor at the grid side with low harmonic content. Besides, the proposed converter can operate with minimum dc-link voltage values in applications in which the grid and load frequency are the same, such as unified power quality conditioners (UPQC). The proposed configuration is compared to the conventional single-phase four-leg UPQC regarding the amount of power processed by the transformer, rating of semiconductor devices, harmonic distortion, ac-filter size, and semiconductor power losses. The system model, the operational constraints, the power distribution analysis, the overall control system strategy, and a space vector pulse-width modulation that exploits a simplified carrier-based approach are presented. Simulation and experimental results are provided to prove the viability of the system.
- 6 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 59 (6) , 6876-6888
PUC Converter Based on AC-DC-AC Multilevel Topologies With a Shared Leg
In this paper, a single-phase ac-dc-ac multilevel configuration based on packed u-cell (PUC) is investigated. The system consists of a four-leg module with a u-cell connected to the shared part of the system and a low-frequency transformer at the grid side. The proposed converter allows one to compensate for grid voltage sags and swells, and to provide a high power factor at the grid side with low harmonic content. Besides, the proposed converter can operate with minimum dc-link voltage values in applications in which the grid and load frequency are the same, such as unified power quality conditioners (UPQC). The proposed configuration is compared to the conventional single-phase four-leg UPQC regarding the amount of power processed by the transformer, rating of semiconductor devices, harmonic distortion, ac-filter size, and semiconductor power losses. The system model, the operational constraints, the power distribution analysis, the overall control system strategy, and a space vector pulse-width modulation that exploits a simplified carrier-based approach are presented. Simulation and experimental results are provided to prove the viability of the system.
- 3 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 59 (5) , 6360-6372
A Multilevel Open-End Winding Six-Phase Induction Motor Drive Topology Based on Three Two-Level Three-Phase Inverters
This paper presents a nine-leg (9 L) multilevel inverter to drive an asymmetrical six-phase induction machine in an open-end winding (OEW) configuration. The system is based on three conventional two-level three-phase voltage source inverters (VSIs) with three, two, or one isolated dc links. A machine with two sets of 30 degrees shifted three-phase stator windings is considered. The paper discusses the converters operating principles and proposes a simple space-vector pulse-width modulation (SV-PWM) and its implementation through equivalent level-shifted PWM (LS-PWM). Also, a comparative study is presented regarding the discussed 9L-OEW systems and two conventional drives: the six-leg two-level (6 L), and the 12-leg OEW (12L-OEW) systems. The figures of merit were the number of components, required dc-link voltage, voltage and current harmonic distortions, torque ripple, and semiconductor losses. Simulations and experiments show results for a 1 HP machine. Finally, the paper concludes that the characteristics of the 9L-OEW system using three isolated dc links fit between the 6 L and 12L-OEW conventional systems.
- 3 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 59 (5) , 6360-6372
A Multilevel Open-End Winding Six-Phase Induction Motor Drive Topology Based on Three Two-Level Three-Phase Inverters
This paper presents a nine-leg (9 L) multilevel inverter to drive an asymmetrical six-phase induction machine in an open-end winding (OEW) configuration. The system is based on three conventional two-level three-phase voltage source inverters (VSIs) with three, two, or one isolated dc links. A machine with two sets of 30 degrees shifted three-phase stator windings is considered. The paper discusses the converters operating principles and proposes a simple space-vector pulse-width modulation (SV-PWM) and its implementation through equivalent level-shifted PWM (LS-PWM). Also, a comparative study is presented regarding the discussed 9L-OEW systems and two conventional drives: the six-leg two-level (6 L), and the 12-leg OEW (12L-OEW) systems. The figures of merit were the number of components, required dc-link voltage, voltage and current harmonic distortions, torque ripple, and semiconductor losses. Simulations and experiments show results for a 1 HP machine. Finally, the paper concludes that the characteristics of the 9L-OEW system using three isolated dc links fit between the 6 L and 12L-OEW conventional systems.