Kush P. Mehta
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Kush P. Mehta has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
Vishvesh J. Badheka
5 shared publications- Kapil Gupta
University of Johannesburg
4 shared publications Vishvesh Badheka
3 shared publicationsAshish Yadav
ITER-India, Institute of Plasma Research, Ahmedabad, India
2 shared publicationsBharat Doshi
2 shared publicationsHardik Vyas
2 shared publications
Latest Publications
- 9 June 2022
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 288
Dissimilar friction stir welding of Al to non-Al metallic materials: An overview
- 9 June 2022
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 288
Dissimilar friction stir welding of Al to non-Al metallic materials: An overview
- Open Access
- 1 January 2022
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 832
Microstructure evolution and mechanical properties of continuous drive friction welded dissimilar copper-stainless steel pipe joints
- 1 January 2022
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 832
Open AccessMicrostructure evolution and mechanical properties of continuous drive friction welded dissimilar copper-stainless steel pipe joints
- Open Access
- 18 October 2021
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 37 (8) , 908-920
Investigation on stability of weld morphology, microstructure of processed zones, and weld quality assessment for hot wire gas tungsten arc welding of electrolytic tough pitch copper
In the present investigation, stability of weld morphology was investigated in case of electrolytic tough pitch copper (12 mm thickness) processed by Hot Wire Gas Tungsten Arc Welding (HW GTAW) using CuNi filler wire with variations of processing conditions, using different combination of hot wire’s parameters such as feed rate and current. The assessment of weld bead geometry was performed using visual examination (during and after welding), and macrographic dimensional measurements of weld bead geometry such as depth of penetration and depth to width ratio. In addition to the stability of weld bead geometries, microstructural variations and weld quality assessments were studied using optical microscopy, scanning electron microscopy, energy dispersive x-ray spectroscopy, and micro-hardness measurements in case of processed sample observed with most uniform weld bead geometry. The results revealed that minimum dimensional variations of weld bead geometry throughout the processed length was obtained with 5.42 mm bead width, 1.2 mm bead height, 1.8 mm penetration, and 0.36 depth to width ratio when hot wire’s parameters were 0.6 m/min wire feed rate and 90 amps hot wire current. The bridging mode of metal transfer helps to receive more stable weld bead geometry with minimum dimensional variations. Ni filler wire of HW GTAW improves the hardness in the Heat affected zone (70 HV0.3) and weld zone (80 HV0.3), which were 33% and 17% higher of base material. The weld zone was consisting of mixed mode of grains such as dendrites just above the fusion line and cellular grains further above dendrites in case of processed sample of minimum dimensional variations of weld bead geometry throughout the processed length.
- 18 October 2021
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 37 (8) , 908-920
Open AccessInvestigation on stability of weld morphology, microstructure of processed zones, and weld quality assessment for hot wire gas tungsten arc welding of electrolytic tough pitch copper
In the present investigation, stability of weld morphology was investigated in case of electrolytic tough pitch copper (12 mm thickness) processed by Hot Wire Gas Tungsten Arc Welding (HW GTAW) using CuNi filler wire with variations of processing conditions, using different combination of hot wire’s parameters such as feed rate and current. The assessment of weld bead geometry was performed using visual examination (during and after welding), and macrographic dimensional measurements of weld bead geometry such as depth of penetration and depth to width ratio. In addition to the stability of weld bead geometries, microstructural variations and weld quality assessments were studied using optical microscopy, scanning electron microscopy, energy dispersive x-ray spectroscopy, and micro-hardness measurements in case of processed sample observed with most uniform weld bead geometry. The results revealed that minimum dimensional variations of weld bead geometry throughout the processed length was obtained with 5.42 mm bead width, 1.2 mm bead height, 1.8 mm penetration, and 0.36 depth to width ratio when hot wire’s parameters were 0.6 m/min wire feed rate and 90 amps hot wire current. The bridging mode of metal transfer helps to receive more stable weld bead geometry with minimum dimensional variations. Ni filler wire of HW GTAW improves the hardness in the Heat affected zone (70 HV0.3) and weld zone (80 HV0.3), which were 33% and 17% higher of base material. The weld zone was consisting of mixed mode of grains such as dendrites just above the fusion line and cellular grains further above dendrites in case of processed sample of minimum dimensional variations of weld bead geometry throughout the processed length.
- Open Access
- 1 July 2021
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 13, 2180-2193
Investigation of exit-hole repairing on dissimilar aluminum-copper friction stir welded joints
- 1 July 2021
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 13, 2180-2193
Open AccessInvestigation of exit-hole repairing on dissimilar aluminum-copper friction stir welded joints
- Open Access
- 28 February 2021
- Published by Taylor & Francis in Critical Reviews in Solid State and Materials Sciences
- Vol. 47 (1) , 1-45
A review on friction stir-based channeling
Friction stir-based channeling is a solid-state processing encompassing the friction stir channeling (FSC) and its variants. In one manufacturing action, the FSC delivers a subsurface internal closed channel in a monolithic plate with no length limitation. The unique characteristics of theses internally closed channels produced with FSC can fit the demand from several industrial fields, namely lightweight structurally stiffened panels and applications where high power density requires highly efficient thermal management systems, such as power electronics and electric vehicles-based transportation. This first review on the FSC and its variants encompasses a systematic and comprehensive understanding on physical properties, including thermal performance and channel manufacturability applied to different engineering materials. The discussion is emphasized on working principle of channel formation, tool design, influence of process parameters, geometrical characterization, mechanical properties, hardness field and microstructural features correlated with mechanical properties. It can be summarized that novel processing of channels by FSC enhances the thermal performance compared to conventional fabrication techniques. FSC can produce complex path channels with various sizes, shapes and surface finishing. Precise control on process parameters and material flow governs the channel formation that subsequently influences thermal and mechanical performances of the channels. FSC has been applied to different range of thermal management systems and has potential for many demanding existent applications and enabling new high-performance products. From the initial FSC concept based on a shoulder-workpiece clearance, to the most recent solutions, such as the stationary shoulder FSC, and the no-tilt-angle and no-shoulder-workpiece clearance, allowing the manufacturing of large size channels, leaving the processed surface at its original quota and ready to be used. A significant leap is introduced with the Hybrid FSC enabling simultaneous welding and channeling, of similar and dissimilar metal components, and therefore, enhancing design opportunities for even more competitive solutions.
- 28 February 2021
- Published by Taylor & Francis in Critical Reviews in Solid State and Materials Sciences
- Vol. 47 (1) , 1-45
Open AccessA review on friction stir-based channeling
Friction stir-based channeling is a solid-state processing encompassing the friction stir channeling (FSC) and its variants. In one manufacturing action, the FSC delivers a subsurface internal closed channel in a monolithic plate with no length limitation. The unique characteristics of theses internally closed channels produced with FSC can fit the demand from several industrial fields, namely lightweight structurally stiffened panels and applications where high power density requires highly efficient thermal management systems, such as power electronics and electric vehicles-based transportation. This first review on the FSC and its variants encompasses a systematic and comprehensive understanding on physical properties, including thermal performance and channel manufacturability applied to different engineering materials. The discussion is emphasized on working principle of channel formation, tool design, influence of process parameters, geometrical characterization, mechanical properties, hardness field and microstructural features correlated with mechanical properties. It can be summarized that novel processing of channels by FSC enhances the thermal performance compared to conventional fabrication techniques. FSC can produce complex path channels with various sizes, shapes and surface finishing. Precise control on process parameters and material flow governs the channel formation that subsequently influences thermal and mechanical performances of the channels. FSC has been applied to different range of thermal management systems and has potential for many demanding existent applications and enabling new high-performance products. From the initial FSC concept based on a shoulder-workpiece clearance, to the most recent solutions, such as the stationary shoulder FSC, and the no-tilt-angle and no-shoulder-workpiece clearance, allowing the manufacturing of large size channels, leaving the processed surface at its original quota and ready to be used. A significant leap is introduced with the Hybrid FSC enabling simultaneous welding and channeling, of similar and dissimilar metal components, and therefore, enhancing design opportunities for even more competitive solutions.
- Open Access
- 4 July 2020
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 20 (3) , 1-17
Effect of shoulder features during friction spot extrusion welding of 2024-T3 to 6061-T6 aluminium alloys
Friction spot extrusion welding process is successfully performed on dissimilar aluminum alloys of AA2024-T3 and AA6061-T6 under the influence of shoulder features. The joints were analysed by microstructural features and mechanical properties using conventional and advanced tools of visual inspection, optical microscopy, scanning electron microscopy, transmission electron microscopy, electron back scattered diffractions, tensile testing and hardness testing. The results revealed that the joining was obtained by combination of mechanical locking from extruded material of top surface to predrilled bottom surface and diffusion in solid state. The stir zone and plastically deformed metal flow zone were influenced by scroll shoulder and smooth shoulder features. The tensile specimen of scroll shoulder was resulted to higher fracture load of 6381 N whereas the same was 4916 N in case of smooth shoulder. The interface of between plastically deformed metal flow zone and base material of AA6061-T6 can be considered as critical/weakest zone in case of friction spot extrusion. The variations of hardness were observed in stir zone, plastically deformed metal flow zone and thermo-mechanically affected zone in case of friction spot extrusion welding process.
- 4 July 2020
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 20 (3) , 1-17
Open AccessEffect of shoulder features during friction spot extrusion welding of 2024-T3 to 6061-T6 aluminium alloys
Friction spot extrusion welding process is successfully performed on dissimilar aluminum alloys of AA2024-T3 and AA6061-T6 under the influence of shoulder features. The joints were analysed by microstructural features and mechanical properties using conventional and advanced tools of visual inspection, optical microscopy, scanning electron microscopy, transmission electron microscopy, electron back scattered diffractions, tensile testing and hardness testing. The results revealed that the joining was obtained by combination of mechanical locking from extruded material of top surface to predrilled bottom surface and diffusion in solid state. The stir zone and plastically deformed metal flow zone were influenced by scroll shoulder and smooth shoulder features. The tensile specimen of scroll shoulder was resulted to higher fracture load of 6381 N whereas the same was 4916 N in case of smooth shoulder. The interface of between plastically deformed metal flow zone and base material of AA6061-T6 can be considered as critical/weakest zone in case of friction spot extrusion. The variations of hardness were observed in stir zone, plastically deformed metal flow zone and thermo-mechanically affected zone in case of friction spot extrusion welding process.
- 30 June 2020
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 35 (15) , 1707-1716
Processing of copper by keyhole gas tungsten arc welding for uniformity of weld bead geometry
Keyhole gas tungsten arc welding (K-GTAW) was applied to characterize the weld bead geometry in case of the 6 mm thick electrolytic tough pitch copper. Various conditions of welding speeds and preheating on the bead geometry were studied for its uniformity. Visual examination, macro bead dimensional analysis, microhardness profile across the transverse section, microstructural analyses were performed to investigate the K-GTAW on electrolytic tough pitch copper. The results revealed that full penetration of 6 mm can be obtained in a single pass using keyhole mode in GTAW. Keyhole length and width were majorly affected by the welding speed and preheating temperature. Significant variations in weld bead geometry were observed even when high heat input conditions were applied without preheating. Uniform weld bead geometry of 5 mm bead width and depth to width ratio of 0.42 was obtained for a length of 80 mm using appropriate preheating of 300°C and heat input condition of 1.37 kJ/mm (resulted from 300 amperes welding current, 120 mm/min welding speed, and 15.3 volts voltage). In the uniform weld bead geometry, the weld and heat affected zones were consisted of coarse grains relative to base material, wherein the micro hardness variations were observed.
- 30 June 2020
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 35 (15) , 1707-1716
Processing of copper by keyhole gas tungsten arc welding for uniformity of weld bead geometry
Keyhole gas tungsten arc welding (K-GTAW) was applied to characterize the weld bead geometry in case of the 6 mm thick electrolytic tough pitch copper. Various conditions of welding speeds and preheating on the bead geometry were studied for its uniformity. Visual examination, macro bead dimensional analysis, microhardness profile across the transverse section, microstructural analyses were performed to investigate the K-GTAW on electrolytic tough pitch copper. The results revealed that full penetration of 6 mm can be obtained in a single pass using keyhole mode in GTAW. Keyhole length and width were majorly affected by the welding speed and preheating temperature. Significant variations in weld bead geometry were observed even when high heat input conditions were applied without preheating. Uniform weld bead geometry of 5 mm bead width and depth to width ratio of 0.42 was obtained for a length of 80 mm using appropriate preheating of 300°C and heat input condition of 1.37 kJ/mm (resulted from 300 amperes welding current, 120 mm/min welding speed, and 15.3 volts voltage). In the uniform weld bead geometry, the weld and heat affected zones were consisted of coarse grains relative to base material, wherein the micro hardness variations were observed.
- 5 June 2020
- Published by Springer Nature in Metals and Materials International
- Vol. 27 (8) , 3085-3094
Metallurgical and Mechanical Properties of Al–Cu Joint by Friction Stir Spot Welding and Modified Friction Stir Clinching
- 5 June 2020
- Published by Springer Nature in Metals and Materials International
- Vol. 27 (8) , 3085-3094
Metallurgical and Mechanical Properties of Al–Cu Joint by Friction Stir Spot Welding and Modified Friction Stir Clinching