Enrico Mattarelli

Dual fuel combustion has gained attention as a cost-effective solution for reducing the pollutant emissions of internal combustion engines. The typical approach is combining a conventional high-reactivity fossil fuel (diesel fuel) with a sustainable low-reactivity fuel, such as bio-methane, ethanol, or green hydrogen. The last one is particularly interesting, as in theory it produces only water and NO_x when it burns. However, integrating hydrogen into stock diesel engines is far from trivial due to a number of theoretical and practical challenges, mainly related to the control of combustion at different loads and speeds. The use of 3D-CFD simulation, supported by experimental data, appears to be the most effective way to address these issues. This study investigates the hydrogen-diesel dual fuel concept implemented with minimum modifications in a light-duty diesel engine (2.8 L, 4-cylinder, direct injection with common rail), considering two operating points representing typical partial and full load conditions for a light commercial vehicle or an industrial engine. The numerical analysis explores the effects of progressively replacing diesel fuel with hydrogen, up to 80% of the total energy input. The goal is to assess how this substitution affects engine performance and combustion characteristics. The results show that a moderate hydrogen substitution improves brake thermal efficiency, while higher substitution rates present quite a severe challenge. To address these issues, the diesel fuel injection strategy is optimized under dual fuel operation. The research findings are promising, but they also indicate that further investigations are needed at high hydrogen substitution rates in order to exploit the potential of the concept.

A significant challenge in utilizing hydrogen in conventional internal combustion engines is achieving a balance between NOx emissions and brake power output. A lean premixed charge (Lambda ≈ 2.5) allows for efficient and stable combustion with minimal NOx emissions. However, this comes at the cost of reduced power density due to the higher air requirements of the thermodynamic process. While supercharging can mitigate this drawback, it introduces increased complexity, cost, and size. An intriguing alternative is the 2-stroke cycle, particularly in an opposed piston (OP) configuration. This study presents the virtual development of a single-cylinder 2-stroke OP engine with a total displacement of 0.95 L, designed to deliver 25 kW at 3000 rpm. Thanks to its compact size, high thermal efficiency, robustness, modularity, and low manufacturing cost, this engine is intended for use either as an industrial power unit or in combination with electric motors in hybrid vehicles. The overarching goal of this project is to demonstrate that internal combustion engines can offer a practical and cost-effective alternative to hydrogen fuel cells without significant penalties in terms of efficiency and pollutant emissions. The design of this novel engine started from scratch, and both 1D and 3D CFD simulations were employed, with particular focus on optimizing the cylinder’s geometry and developing an efficient low-pressure injection system. The numerical methodology was based on state-of-the-art commercial codes, in line with established engineering practices. The numerical results indicated that the optimized engine configuration slightly surpasses the target performance, achieving 29 kW at 3000 rpm, while maintaining near-zero NOx emissions (<20 ppm) and high brake thermal efficiency (~40%) over a wide power range. Additionally, the cost of this engine is projected to be lower than an equivalent 4-stroke engine, due to fewer components (e.g., no cylinder head, poppet valves, or camshafts) and a lighter construction.

Micro-cogeneration with locally produced biogas from waste is a proven technique for supporting the decarbonization process. However, the strongly variable composition of biogas can make its use in internal combustion engines quite challenging. Dual-fuel engines offer advantages over conventional SI and diesel engines, but there are still issues to be addressed, such as the low-load thermodynamic efficiency and nitrogen oxide emissions. In particular, it is highly desirable to reduce NO_x directly in the combustion chamber in order to avoid expensive after-treatment systems. This study analyzed the influence of the combustion system, especially the piston bowl geometry and the injector nozzle, on the performance and emissions of a dual-fuel diesel–biogas engine designed for micro-cogeneration (maximum electric power: 50 kW). In detail, four different cylindrical piston bowls characterized by radii of 23, 28, 33 and 38 mm were compared with a conventional omega-shaped diesel bowl. Moreover, the influence of the injector tip position and the jet tilt angle was analyzed over ranges of 2–10 mm and 30–120°, respectively. The goal of the optimization was to find a configuration that was able to reduce the amount of NO_x while maintaining high values of brake thermal efficiency at all the engine operating conditions. For this purpose, a 3D-CFD investigation was carried out by means of a customized version of the KIVA-3V code at both full load (BMEP = 8 bar, 3000 rpm, maximum brake power) and partial load (BMEP = 4 bar, 3000 rpm). The novelty of the study consisted of the parametric approach to the problem and the high number of investigated parameters. The results indicated that the standard design of the piston bowl yielded a near-optimal trade-off at full load between the thermodynamic efficiency and pollutant emissions; however, at a lower load, significant advantages could be found by designing a deeper cylindrical bowl with a smaller radius. In particular, a new bowl characterized by a radius of 23 mm was equivalent to the standard one at BMEP = 8 bar, but it yielded a NO_x-specific reduction of 38% at BMEP = 4 bar with the same value of BTE.

The present work aims to assess the influence of the composition of blends of hydrogen (H₂) and Natural Gas (NG) on Dual Fuel (DF) combustion characteristics, including gaseous emissions. The 3D-CFD study is carried out by means of a customized version of the KIVA-3V code. An automotive 2.8 L, 4-cylinder turbocharged diesel engine was previously modified in order to operate in DF NG–diesel mode, and tested at the dynamometer bench. After validation against experimental results, the numerical model is applied to perform a set of combustion simulations at 3000 rpm–BMEP = 8 bar, in DF H₂/NG-diesel mode. Different H₂–NG blends are considered: as the H₂ mole fraction varies from 0 vol% to 50 vol%, the fuel energy within the premixed charge is kept constant. The influence of the diesel Start Of Injection (SOI) is also investigated. Simulation results demonstrate that H₂ enrichment accelerates the combustion process and promotes its completion, strongly decreasing UHC and CO emissions. Evidently, CO₂ specific emissions are also reduced (up to about 20%, at 50 vol% of H₂). The main drawbacks of the faster combustion include an increase of in-cylinder peak pressure and pressure rate rise, and of NO_x emissions. However, the study demonstrates that the optimization of diesel SOI can eliminate all aforementioned shortcomings.

Reactivity Controlled Compression Ignition (RCCI) is one of the most promising solutions among the low temperature combustion concepts, in terms of thermal efficiency and pollutant emissions. However, for values of brake mean effective pressure higher than 10 bar, in-cylinder peak pressure rise rates tend to be too high, limiting the specific power of any 4-Stroke (4S) engine. Such a limitation can be canceled by moving to the 2-Stroke (2S) cycle. Among many alternatives, the “Uniflow” scavenging system with exhaust poppet valves on the cylinder head allows the designer to reproduce the same identical combustion patterns of a 4-stroke RCCI engine, while increasing the indicated power output. The goal of the paper is to explore the potential of a 2-stroke RCCI engine, on the basis of a comprehensive experimental campaign carried out on a modified automotive 2.0 L, 4-stroke, four-cylinder, four-valve diesel engine. The developed prototype can run with one cylinder operating in 4-stroke RCCI mode (gasoline–diesel), while the others work in the standard diesel mode. A One Dimensional-Computational Fluid Dynamics (1D-CFD) model has been built to predict the performance of the same prototype, when operating all four cylinders in RCCI mode. In parallel, an equivalent 2-stroke RCCI virtual engine has been developed, by means of 1D-CFD simulations and empirical assumptions. A numerical comparison between the 4S and the 2S engines is finally presented, in terms of performance and emissions at full load. The study demonstrates that a 2S RCCI engine can maintain all of the advantages of the RCCI combustion, strongly reducing the penalization in terms of performance, in comparison to a standard 4S diesel engine.

Hydraulic manifolds are used to realize compact circuit layout, but may introduce a high pressure drop in the system. Their design is in fact oriented more toward achieving minimum size and weight than to reducing pressure losses. This work studies the pressure losses in hydraulic manifolds using different methods: Computational Fluid Dynamic (CFD) analysis; semi-empirical formulation derived from the scientific literature, when available; and experimental characterization. The purpose is to obtain the pressure losses when the channels’ connections within the manifold are not ascribable to the few classic cases studied in the literature, in particular for 90° bends (elbows) with expansion/contraction and offset intersection of channels. Moreover, since CFD analysis is used to predict pressure losses, general considerations of the manifold design may be outlined and this will help the design process in the optimization of flow passages. The main results obtained show how CFD analysis overestimates the experimental results; nevertheless, the numerical analysis represents the correct trends of the pressure losses.