Luca D'AGostino
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Luca D'AGostino has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Angelo Pasini
University of Pisa
13 shared publications - Lucio Torre
Alta S.p.A., 5 Via Gherardesca, Ospedaletto, Pisa 56121, Italy
6 shared publications - Angelo Cervone
Delft University of Technology (TU Delft)
5 shared publications - Dario Valentini
Department of Civil and Industrial Engineering, University of Pisa , Via G. Caruso 12, Pisa 56122, Italy
5 shared publications Dario Valentini
4 shared publications- Giovanni Pace
SITAEL S.p.A., Via Alessandro Gherardesca 5, Pisa 56121, Italy
4 shared publications
Latest Publications
- 1 November 2023
- Published by ASME International in Journal of Fluids Engineering
- Vol. 146 (3) , 1-56
Maximum Likelihood Identification of Backflow Vortex Instability in Rocket Engine Inducers
Bayesian estimation is applied to the analysis of backflow vortex instabilities in typical three- and four-bladed liquid propellant rocket engine inducers. The flow in the impeller eye is modeled as a set of equally intense and evenly spaced 2D axial vortices, located at the same radial distance from the axis and rotating at a fraction of the impeller speed. The circle theorem is used to predict the flow pressure in terms of the vortex number, intensity, rotational speed, and radial position. The theoretical spectra so obtained are frequency broadened to mimic the dispersion of the experimental results and parametrically fitted to the measured data by maximum likelihood estimation with equal and independent Gaussian errors. The method is applied to three inducers, tested in water at room temperature and different operating conditions. It successfully characterizes backflow instabilities using the signals of a single pressure transducer flush-mounted in the impeller eye, effectively bypassing the aliasing limitations and the data acquisition/reduction complexities of traditional multiple-sensor cross-correlation methods. The identification returns the estimates of the model parameters and their standard deviations, providing the information necessary for assessing the accuracy and statistical significance of the results. The flowrate is found to be the major factor affecting the backflow vortex instability, which, on the other hand, is rather insensitive to the occurrence of cavitation. The results are consistent with the data reported in the literature, as well as with those generated by the auxiliary models specifically developed for initializing the maximum likelihood searches and supporting the identification procedure.
- 1 November 2023
- Published by ASME International in Journal of Fluids Engineering
- Vol. 146 (3) , 1-56
Maximum Likelihood Identification of Backflow Vortex Instability in Rocket Engine Inducers
Bayesian estimation is applied to the analysis of backflow vortex instabilities in typical three- and four-bladed liquid propellant rocket engine inducers. The flow in the impeller eye is modeled as a set of equally intense and evenly spaced 2D axial vortices, located at the same radial distance from the axis and rotating at a fraction of the impeller speed. The circle theorem is used to predict the flow pressure in terms of the vortex number, intensity, rotational speed, and radial position. The theoretical spectra so obtained are frequency broadened to mimic the dispersion of the experimental results and parametrically fitted to the measured data by maximum likelihood estimation with equal and independent Gaussian errors. The method is applied to three inducers, tested in water at room temperature and different operating conditions. It successfully characterizes backflow instabilities using the signals of a single pressure transducer flush-mounted in the impeller eye, effectively bypassing the aliasing limitations and the data acquisition/reduction complexities of traditional multiple-sensor cross-correlation methods. The identification returns the estimates of the model parameters and their standard deviations, providing the information necessary for assessing the accuracy and statistical significance of the results. The flowrate is found to be the major factor affecting the backflow vortex instability, which, on the other hand, is rather insensitive to the occurrence of cavitation. The results are consistent with the data reported in the literature, as well as with those generated by the auxiliary models specifically developed for initializing the maximum likelihood searches and supporting the identification procedure.
- 4 March 2022
- Published by Elsevier in Aerospace Science and Technology
- Vol. 123
Concurrent theoretical, experimental and numerical analyses of mixed-flow turbopump design
- 4 March 2022
- Published by Elsevier in Aerospace Science and Technology
- Vol. 123
Concurrent theoretical, experimental and numerical analyses of mixed-flow turbopump design
- 10 August 2021
- Published by ASME International
Parametric Identification of Rotating Cavitation in a Three-Bladed Axial Inducer
The article illustrates the application of Bayesian estimation to the identification of flow instabilities, with special reference to rotating cavitation, in a three-bladed axial inducer using the unsteady pressure readings of a single transducer mounted on the casing just behind the leading edges of the impeller blades. The typical trapezoidal pressure distribution in the blade channels is parametrized and modulated in time and space for theoretically reproducing the expected pressure generated by known forms of cavitation instabilities (cavitation auto-oscillations, n-lobed rotating cavitation, higher-order surge/rotating cavitation modes). The Fourier spectra of the theoretical pressure so obtained in the rotating frame are transformed in the stationary frame, frequency broadened to better approximate the experimental results, and parametrically fitted by maximum likelihood estimation to the measured auto-correlation spectra. Each form of instability generates a characteristic distribution of sidebands in addition to its fundamental frequency. The identification makes use of this information for effective detection and characterization of multiple simultaneous flow instabilities with intensities spanning over about 20 dB down to about 4 dB signal-to-noise ratios. The same information also allows for effectively bypassing the aliasing limitations of traditional cross-correlation methods in the discrimination of multiple-lobed azimuthal instabilities from dual-sensor measurements on the same axial station of the machine. The method returns both the estimates of the model parameters and their standard deviations, providing the information needed for the assessment of the statistical significance of the results. The proposed approach represents therefore a promising tool for experimental research on flow instabilities in high-performance turbopumps.
- 10 August 2021
- Published by ASME International
Parametric Identification of Rotating Cavitation in a Three-Bladed Axial Inducer
The article illustrates the application of Bayesian estimation to the identification of flow instabilities, with special reference to rotating cavitation, in a three-bladed axial inducer using the unsteady pressure readings of a single transducer mounted on the casing just behind the leading edges of the impeller blades. The typical trapezoidal pressure distribution in the blade channels is parametrized and modulated in time and space for theoretically reproducing the expected pressure generated by known forms of cavitation instabilities (cavitation auto-oscillations, n-lobed rotating cavitation, higher-order surge/rotating cavitation modes). The Fourier spectra of the theoretical pressure so obtained in the rotating frame are transformed in the stationary frame, frequency broadened to better approximate the experimental results, and parametrically fitted by maximum likelihood estimation to the measured auto-correlation spectra. Each form of instability generates a characteristic distribution of sidebands in addition to its fundamental frequency. The identification makes use of this information for effective detection and characterization of multiple simultaneous flow instabilities with intensities spanning over about 20 dB down to about 4 dB signal-to-noise ratios. The same information also allows for effectively bypassing the aliasing limitations of traditional cross-correlation methods in the discrimination of multiple-lobed azimuthal instabilities from dual-sensor measurements on the same axial station of the machine. The method returns both the estimates of the model parameters and their standard deviations, providing the information needed for the assessment of the statistical significance of the results. The proposed approach represents therefore a promising tool for experimental research on flow instabilities in high-performance turbopumps.
- 28 July 2021
- Published by American Institute of Aeronautics and Astronautics (AIAA)
Design of an Affordable Hydrogen Peroxide Propulsion System for CubeSats
View Video Presentation: https://doi.org/10.2514/6.2021-3690.vid The CubeSats market is continuously growing in recent years, pushing the need to provide this satellite class of propulsion systems for orbit maneuverability. In this context, Green Propellants' chemical monopropellant propulsion systems are a competitive solution with respect to more popular electric ones. This paper presents the design of an affordable propulsion system for CubeSats powered by Hydrogen Peroxide. The design focused on the storage subsystem and the thruster. An innovative modular cubic tank of 1 U volume is proposed, which permits to maximize the propulsive performance. The designed solution offers a low-cost, low power consumption, and compact system that is able to perform the typical maneuvers for CubeSats. The presented architecture powered by HTP is compared with other green monopropellant solutions, proving to be a valid competitive option in the market of propulsion systems for CubeSat.
- 28 July 2021
- Published by American Institute of Aeronautics and Astronautics (AIAA)
Design of an Affordable Hydrogen Peroxide Propulsion System for CubeSats
View Video Presentation: https://doi.org/10.2514/6.2021-3690.vid The CubeSats market is continuously growing in recent years, pushing the need to provide this satellite class of propulsion systems for orbit maneuverability. In this context, Green Propellants' chemical monopropellant propulsion systems are a competitive solution with respect to more popular electric ones. This paper presents the design of an affordable propulsion system for CubeSats powered by Hydrogen Peroxide. The design focused on the storage subsystem and the thruster. An innovative modular cubic tank of 1 U volume is proposed, which permits to maximize the propulsive performance. The designed solution offers a low-cost, low power consumption, and compact system that is able to perform the typical maneuvers for CubeSats. The presented architecture powered by HTP is compared with other green monopropellant solutions, proving to be a valid competitive option in the market of propulsion systems for CubeSat.
- 8 November 2019
- Published by ASME International in Journal of Fluids Engineering
- Vol. 142 (2)
Identification of Cavitation Instabilities on a Three-Bladed Inducer by Means of Strain Gages
This paper reports the experimental characterization of the cavitation-induced flow instabilities of a high head three-bladed inducer at design condition detected simultaneously by means of piezoelectric pressure transducers located at different axial and azimuthal stations on the casing of the pump and strain gages mounted on the pressure side of each blade. The simultaneous analysis performed in the stationary and rotating frames, supported by high-speed movies, suggests that the mechanism of formation of the detected subsynchronous rotating cavitation resembles that of modal stall in compressors, being the cavitation region the source of compliance. In fact, at decreasing cavitation number, a strong attached cavitation, developed preferentially on one blade and capable of completely surrounding and unloading the following blade, starts to be destabilized as consequence of the progressive intensification of a modal oscillation. The developed complex instability, consisting in a strong oscillation of the attached cavitation, is detected in both the frames as the simultaneous presence of a subsynchronous rotating cavitation and a cavitation surge.
- 8 November 2019
- Published by ASME International in Journal of Fluids Engineering
- Vol. 142 (2)
Identification of Cavitation Instabilities on a Three-Bladed Inducer by Means of Strain Gages
This paper reports the experimental characterization of the cavitation-induced flow instabilities of a high head three-bladed inducer at design condition detected simultaneously by means of piezoelectric pressure transducers located at different axial and azimuthal stations on the casing of the pump and strain gages mounted on the pressure side of each blade. The simultaneous analysis performed in the stationary and rotating frames, supported by high-speed movies, suggests that the mechanism of formation of the detected subsynchronous rotating cavitation resembles that of modal stall in compressors, being the cavitation region the source of compliance. In fact, at decreasing cavitation number, a strong attached cavitation, developed preferentially on one blade and capable of completely surrounding and unloading the following blade, starts to be destabilized as consequence of the progressive intensification of a modal oscillation. The developed complex instability, consisting in a strong oscillation of the attached cavitation, is detected in both the frames as the simultaneous presence of a subsynchronous rotating cavitation and a cavitation surge.
- 13 November 2018
- Published by ASME International in Journal of Fluids Engineering
- Vol. 141 (4)
Analysis of Flow Instabilities on a Three-Bladed Axial Inducer in Fixed and Rotating Frames
The paper describes the results of recent experiments carried out in the Cavitating Pump Rotordynamic Test Facility for the dynamic characterization of cavitation-induced flow instabilities as simultaneously observed in the stationary and rotating frames of a high-head, three-bladed axial inducer with tapered hub and variable pitch. The flow instabilities occurring in the eye and inside the blading of the inducer have been detected, identified, and monitored by means of the spectral analysis of the pressure measurements simultaneously performed in the stationary and rotating frames by multiple transducers mounted on the casing near the inducer eye and on the inducer hub along the blade channels. An interaction between the unstable flows in the pump inlet and in the blade channels during cavitating regime has been detected. The interaction is between a low frequency axial phenomenon, which cyclically fills and empties each blade channel with cavitation, and a rotating phenomenon detected in the inducer eye.
- 13 November 2018
- Published by ASME International in Journal of Fluids Engineering
- Vol. 141 (4)
Analysis of Flow Instabilities on a Three-Bladed Axial Inducer in Fixed and Rotating Frames
The paper describes the results of recent experiments carried out in the Cavitating Pump Rotordynamic Test Facility for the dynamic characterization of cavitation-induced flow instabilities as simultaneously observed in the stationary and rotating frames of a high-head, three-bladed axial inducer with tapered hub and variable pitch. The flow instabilities occurring in the eye and inside the blading of the inducer have been detected, identified, and monitored by means of the spectral analysis of the pressure measurements simultaneously performed in the stationary and rotating frames by multiple transducers mounted on the casing near the inducer eye and on the inducer hub along the blade channels. An interaction between the unstable flows in the pump inlet and in the blade channels during cavitating regime has been detected. The interaction is between a low frequency axial phenomenon, which cyclically fills and empties each blade channel with cavitation, and a rotating phenomenon detected in the inducer eye.
- Open Access
- 13 November 2018
- Published by ASME International in Journal of Fluids Engineering
- Vol. 141 (4)
Dynamics of the Blade Channel of an Inducer Under Cavitation-Induced Instabilities
A high-head three-bladed inducer has been equipped with pressure taps on the hub along the blade channels with the aim of more closely investigating the dynamics of cavitation-induced instabilities developing in the impeller flow. Spectral analysis of the pressure signals obtained from two sets of transducers mounted both in the stationary and rotating frames has allowed to characterize the nature, intensity, and interactions of the main flow instabilities detected in the experiments: subsynchronous rotating cavitation (RC), cavitation surge (CS), and a high-order axial surge oscillation. A dynamic model of the unsteady flow in the blade channels has been developed based on experimental data and on suitable descriptions of the mean flow and the oscillations of the cavitating volume. The model has been used for estimating at the inducer operating conditions of interest the intensity of the flow oscillations associated with the occurrence of the CS mode generated by RC in the inducer inlet.
- 13 November 2018
- Published by ASME International in Journal of Fluids Engineering
- Vol. 141 (4)
Open AccessDynamics of the Blade Channel of an Inducer Under Cavitation-Induced Instabilities
A high-head three-bladed inducer has been equipped with pressure taps on the hub along the blade channels with the aim of more closely investigating the dynamics of cavitation-induced instabilities developing in the impeller flow. Spectral analysis of the pressure signals obtained from two sets of transducers mounted both in the stationary and rotating frames has allowed to characterize the nature, intensity, and interactions of the main flow instabilities detected in the experiments: subsynchronous rotating cavitation (RC), cavitation surge (CS), and a high-order axial surge oscillation. A dynamic model of the unsteady flow in the blade channels has been developed based on experimental data and on suitable descriptions of the mean flow and the oscillations of the cavitating volume. The model has been used for estimating at the inducer operating conditions of interest the intensity of the flow oscillations associated with the occurrence of the CS mode generated by RC in the inducer inlet.
- Open Access
- 7 May 2018
- Published by MDPI AG in International Journal of Turbomachinery, Propulsion and Power
- Vol. 3 (2) , 13
Experimental Characterization of Unsteady Forces Triggered by Cavitation on a Centrifugal Pump
The paper presents an experimental campaign aimed at the characterization of the relationship between cavitation-induced instabilities and forces acting on the shaft, relevant to space application turbopumps. The experiments have been carried out on a six-bladed unshrouded centrifugal turbopump. Pressure fluctuations are analyzed in their frequency content for understanding the instability nature (axial, rotating) and their main characteristics (e.g., amplitude, rotating direction). The spectral analysis of the force components highlights a strong relationship of the z-component (along the rotating axis) with axial instabilities. On the other hand, rotating cavitation may involve force oscillations along all the three components leading to unwanted and dangerous fluctuating unbalances perpendicular to the rotating axis.
- 7 May 2018
- Published by MDPI AG in International Journal of Turbomachinery, Propulsion and Power
- Vol. 3 (2) , 13
Open AccessExperimental Characterization of Unsteady Forces Triggered by Cavitation on a Centrifugal Pump
The paper presents an experimental campaign aimed at the characterization of the relationship between cavitation-induced instabilities and forces acting on the shaft, relevant to space application turbopumps. The experiments have been carried out on a six-bladed unshrouded centrifugal turbopump. Pressure fluctuations are analyzed in their frequency content for understanding the instability nature (axial, rotating) and their main characteristics (e.g., amplitude, rotating direction). The spectral analysis of the force components highlights a strong relationship of the z-component (along the rotating axis) with axial instabilities. On the other hand, rotating cavitation may involve force oscillations along all the three components leading to unwanted and dangerous fluctuating unbalances perpendicular to the rotating axis.
- 18 March 2017
- Published by Springer Nature
- p. 157-178
On the Preliminary Design and Performance Prediction of Centrifugal Turbopumps—Part 2
- 18 March 2017
- Published by Springer Nature
- p. 157-178
On the Preliminary Design and Performance Prediction of Centrifugal Turbopumps—Part 2
- 18 March 2017
- Published by Springer Nature
- p. 1-33
An Introduction to Cavitation in Inducers and Turbopumps
- 18 March 2017
- Published by Springer Nature
- p. 1-33
An Introduction to Cavitation in Inducers and Turbopumps