Elias Shokati Asl
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Elias Shokati Asl has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Ebrahim Babaei
Faculty of Electrical and Computer Engineering, University of Tabriz, Tabriz, Iran
9 shared publications Mehran Sabahi
Faculty of Electrical and Computer Engineering University of Tabriz Tabriz Iran
5 shared publicationsEbrahim Babaei
Faculty of Electrical and Computer Engineering University of Tabriz Tabriz Iran
2 shared publications- Mohsen Hasan Babayi Nozadian
Department of Electrical Engineering, Faculty of Engineering, Bu-Ali Sina University, Hamedan, 651673-8695, Iran.
2 shared publications Alireza Eyvazizadeh Khosroshahi
School of Engineering, University of British Columbia, Kelowna, BC, Canada
1 shared publication- Andrii Chub
Tallinn University of Technology
1 shared publication
Latest Publications
- 17 February 2026
- Published by Taylor & Francis in International Journal of Electronics
- Vol. 113 (8) , 1471-1491
Γ-Z-source based half-bridge inverter with high boost-voltage ability
- 17 February 2026
- Published by Taylor & Francis in International Journal of Electronics
- Vol. 113 (8) , 1471-1491
Γ-Z-source based half-bridge inverter with high boost-voltage ability
- Open Access
- 1 January 2026
- Published by Institution of Engineering and Technology (IET) in IET Intelligent Transport Systems
- Vol. 20 (1) , e70331
Data‐Driven Spatial Intelligence Framework for Equitable EV Charging Infrastructure Deployment in Urban China
The rapid expansion of electric vehicle (EV) adoption in urban China has intensified the need for scalable, data‐driven approaches to charging infrastructure planning. This study presents a geo‐economic machine learning framework that identifies the spatial, infrastructural, and economic characteristics associated with existing electric vehicle charging station (EVCS) locations and applies the learned patterns to evaluate suitability and rank candidate sites across 500 m × 500 m grid cells. The framework was developed using multi‐source spatial datasets, including road network topology, points of interest, population density, land‐use classifications, and existing EVCS locations. Seventeen binary geo‐economic features were evaluated using multiple supervised classification algorithms under a leave‐one‐city‐out cross‐validation strategy to ensure geographic independence and assess model transferability. The analytical dataset comprised 20,153 grid cells, including 1861 EVCS‐positive locations, highlighting the class‐imbalanced nature of the siting problem. Among the evaluated models, the Bernoulli Naïve Bayes classifier demonstrated the strongest performance, achieving an AUC‐ROC of 0.812 and a Recall of 0.812. The application of the Synthetic Minority Oversampling Technique (SMOTE) further improved Recall to 0.851 while maintaining cross‐city generalisability. Model transferability was assessed using the Economic Transferability Index (ETI), which jointly evaluates predictive accuracy and performance stability across cities. Bernoulli Naïve Bayes achieved the highest ETI values, indicating superior robustness and consistency across diverse urban environments. SHAP‐based interpretability analysis identified population density, commercial point‐of‐interest density, and road network centrality as the most influential positive predictors of EVCS suitability, while distance from the city centre exhibited a negative influence. Spatial autocorrelation analysis revealed significant clustering of suitable locations, supporting zone‐based planning strategies over uniform deployment approaches. Statistical testing confirmed the significance of the model's performance advantage over competing classifiers.
- 1 January 2026
- Published by Institution of Engineering and Technology (IET) in IET Intelligent Transport Systems
- Vol. 20 (1) , e70331
Open AccessData‐Driven Spatial Intelligence Framework for Equitable EV Charging Infrastructure Deployment in Urban China
The rapid expansion of electric vehicle (EV) adoption in urban China has intensified the need for scalable, data‐driven approaches to charging infrastructure planning. This study presents a geo‐economic machine learning framework that identifies the spatial, infrastructural, and economic characteristics associated with existing electric vehicle charging station (EVCS) locations and applies the learned patterns to evaluate suitability and rank candidate sites across 500 m × 500 m grid cells. The framework was developed using multi‐source spatial datasets, including road network topology, points of interest, population density, land‐use classifications, and existing EVCS locations. Seventeen binary geo‐economic features were evaluated using multiple supervised classification algorithms under a leave‐one‐city‐out cross‐validation strategy to ensure geographic independence and assess model transferability. The analytical dataset comprised 20,153 grid cells, including 1861 EVCS‐positive locations, highlighting the class‐imbalanced nature of the siting problem. Among the evaluated models, the Bernoulli Naïve Bayes classifier demonstrated the strongest performance, achieving an AUC‐ROC of 0.812 and a Recall of 0.812. The application of the Synthetic Minority Oversampling Technique (SMOTE) further improved Recall to 0.851 while maintaining cross‐city generalisability. Model transferability was assessed using the Economic Transferability Index (ETI), which jointly evaluates predictive accuracy and performance stability across cities. Bernoulli Naïve Bayes achieved the highest ETI values, indicating superior robustness and consistency across diverse urban environments. SHAP‐based interpretability analysis identified population density, commercial point‐of‐interest density, and road network centrality as the most influential positive predictors of EVCS suitability, while distance from the city centre exhibited a negative influence. Spatial autocorrelation analysis revealed significant clustering of suitable locations, supporting zone‐based planning strategies over uniform deployment approaches. Statistical testing confirmed the significance of the model's performance advantage over competing classifiers.
- Open Access
- 1 January 2026
- Published by Institution of Engineering and Technology (IET) in IET Circuits, Devices & Systems
- Vol. 2026 (1)
A Comprehensive Review of Fundamental DC/DC Converters: Performance Analysis, Design Considerations, and Applications
Nonisolated direct current (DC)–DC converters serve as critical building blocks in modern power management systems. The choice of the optimal topology among numerous options has a direct impact on the efficiency, size, and final cost of the system. This study presents a comprehensive and critical comparative analysis of five fundamental topologies—buck, boost, buck–boost, Ćuk, and SEPIC—in order to provide a clear framework for their selection based on application requirements. The analysis covers the performance of converters in both continuous conduction mode (CCM) and discontinuous conduction mode (DCM). The evaluation is carried out based on a set of key performance indicators, including critical inductance, output voltage ripple (OVR), voltage and current stresses on switches and diodes, and the continuity nature of input/output current. The results highlight inherent trade‐offs among key design parameters of different converter topologies; specifically, fourth‐order converters, such as Ćuk and SEPIC, exhibit higher switch voltage stress than buck converters for the same voltage gain, indicating a compromise between improved ripple performance and increased component ratings. Ultimately, this study leads to the presentation of a topology selection guide that enables design engineers to consciously choose the most optimal converter according to specific application requirements, such as the need for low input current ripple or structural simplicity. This work serves as a practical and unified reference for power electronics system designers.
- 1 January 2026
- Published by Institution of Engineering and Technology (IET) in IET Circuits, Devices & Systems
- Vol. 2026 (1)
Open AccessA Comprehensive Review of Fundamental DC/DC Converters: Performance Analysis, Design Considerations, and Applications
Nonisolated direct current (DC)–DC converters serve as critical building blocks in modern power management systems. The choice of the optimal topology among numerous options has a direct impact on the efficiency, size, and final cost of the system. This study presents a comprehensive and critical comparative analysis of five fundamental topologies—buck, boost, buck–boost, Ćuk, and SEPIC—in order to provide a clear framework for their selection based on application requirements. The analysis covers the performance of converters in both continuous conduction mode (CCM) and discontinuous conduction mode (DCM). The evaluation is carried out based on a set of key performance indicators, including critical inductance, output voltage ripple (OVR), voltage and current stresses on switches and diodes, and the continuity nature of input/output current. The results highlight inherent trade‐offs among key design parameters of different converter topologies; specifically, fourth‐order converters, such as Ćuk and SEPIC, exhibit higher switch voltage stress than buck converters for the same voltage gain, indicating a compromise between improved ripple performance and increased component ratings. Ultimately, this study leads to the presentation of a topology selection guide that enables design engineers to consciously choose the most optimal converter according to specific application requirements, such as the need for low input current ripple or structural simplicity. This work serves as a practical and unified reference for power electronics system designers.
- Open Access
- 1 January 2026
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 19 (1)
A Family of Non‐Isolated High Voltage Gain DC‐DC Converters Based on an Impedance Source Converter and Modular Voltage Lifting Cells
This paper proposes a family of non‐isolated high‐voltage‐gain quadratic DC‐DC converters derived from an impedance source converter. The proposed structure enables the modular use of various voltage lift cells, including the basic switched inductor cell (SL), the quasi‐switched cell (QSC), the improved switched inductor cell (ISL), the elementary lift cell, and the quadratic cell. These converters combine voltage lifting cells and coupled inductors with auxiliary components to achieve high voltage gains and significant benefits. Moreover, there are no duty‐cycle limitations, allowing high voltage gains even at low duty cycles. Additionally, the proposed converters provide several advantages, such as low voltage stress on components, a common ground, continuous input current and high efficiency. The operating modes of the proposed converters are examined. Design considerations for the SL‐ZSC are discussed, along with power loss analyses for the SL‐ZSC and QSC‐ZSC. A comparison between the proposed converters and existing impedance source converters is presented. Finally, a 200 W prototype with a 40 V input and a 300 V output is developed for the proposed SL‐ZSC to verify its validity and effectiveness.
- 1 January 2026
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 19 (1)
Open AccessA Family of Non‐Isolated High Voltage Gain DC‐DC Converters Based on an Impedance Source Converter and Modular Voltage Lifting Cells
This paper proposes a family of non‐isolated high‐voltage‐gain quadratic DC‐DC converters derived from an impedance source converter. The proposed structure enables the modular use of various voltage lift cells, including the basic switched inductor cell (SL), the quasi‐switched cell (QSC), the improved switched inductor cell (ISL), the elementary lift cell, and the quadratic cell. These converters combine voltage lifting cells and coupled inductors with auxiliary components to achieve high voltage gains and significant benefits. Moreover, there are no duty‐cycle limitations, allowing high voltage gains even at low duty cycles. Additionally, the proposed converters provide several advantages, such as low voltage stress on components, a common ground, continuous input current and high efficiency. The operating modes of the proposed converters are examined. Design considerations for the SL‐ZSC are discussed, along with power loss analyses for the SL‐ZSC and QSC‐ZSC. A comparison between the proposed converters and existing impedance source converters is presented. Finally, a 200 W prototype with a 40 V input and a 300 V output is developed for the proposed SL‐ZSC to verify its validity and effectiveness.
- Open Access
- 27 November 2023
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 17 (1) , 38-53
High voltage gain switched z‐source inverter with low current stress
This paper proposes a switched Z‐source inverter with high voltage gain and low current stress on elements. Also, a new switching method corresponding to the proposed topology is introduced. This method is based on the usual Maximum Constant Boost (MCB) method. Hence, it has the advantages of the MCB method, such as low voltage stress on the inverter switches and high voltage gain. Also, eliminating part of the inverter's switching in this modulation method improves the inverter's efficiency. In addition to the Shoot‐Through (ST) duty cycle, another variable (N) affects the inverter's boost factor in this switching method. The proposed inverter's dynamic analysis shows that introducing N in the modulation method improved the dynamic characteristic of the inverter. Also, this variable as a control input can stabilize the dc side of the inverter in the closed‐loop control of the inverter. For the proposed topology, steady‐state analysis, dynamic analysis, elements design and efficiency calculation are performed. Also, the proposed topology is compared with the conventional topologies regarding boost factor, the number of elements, current stress on elements and efficiency to show its superiority. Finally, the experimental results are presented to verify theoretical discussions.
- 27 November 2023
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 17 (1) , 38-53
Open AccessHigh voltage gain switched z‐source inverter with low current stress
This paper proposes a switched Z‐source inverter with high voltage gain and low current stress on elements. Also, a new switching method corresponding to the proposed topology is introduced. This method is based on the usual Maximum Constant Boost (MCB) method. Hence, it has the advantages of the MCB method, such as low voltage stress on the inverter switches and high voltage gain. Also, eliminating part of the inverter's switching in this modulation method improves the inverter's efficiency. In addition to the Shoot‐Through (ST) duty cycle, another variable (N) affects the inverter's boost factor in this switching method. The proposed inverter's dynamic analysis shows that introducing N in the modulation method improved the dynamic characteristic of the inverter. Also, this variable as a control input can stabilize the dc side of the inverter in the closed‐loop control of the inverter. For the proposed topology, steady‐state analysis, dynamic analysis, elements design and efficiency calculation are performed. Also, the proposed topology is compared with the conventional topologies regarding boost factor, the number of elements, current stress on elements and efficiency to show its superiority. Finally, the experimental results are presented to verify theoretical discussions.
- 28 March 2022
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Electrical Engineering
- Vol. 46 (2) , 461-479
A New Type of Half-Bridge Trans-Z-Source Inverter with Continuous Input Current
- 28 March 2022
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Electrical Engineering
- Vol. 46 (2) , 461-479
A New Type of Half-Bridge Trans-Z-Source Inverter with Continuous Input Current
- Open Access
An Embedded Half-Bridge Γ-Z-Source Inverter with Reduced Voltage Stress on Capacitors
In this paper, an embedded half-bridge Z-source inverter based on gamma structure is proposed. In contrast with the classical half-bridge inverter, the proposed inverter can generate zero voltage levels in output. High voltage gain and low voltage stress on capacitors are the main advantages of the proposed converter. The value of the boost factor in the proposed structure is increased by changing both the shoot-through (ST) duty cycle and turns ratio of the transformer. The operating principle of the proposed converter in four operating modes is presented. We also calculate the critical inductance and compare the proposed converter with conventional topologies. In addition, power loss and THD analysis are presented. Finally, PSCAD/EMTDC software is used to verify the correct operation of the proposed inverter and the experimental results.
Open AccessAn Embedded Half-Bridge Γ-Z-Source Inverter with Reduced Voltage Stress on Capacitors
In this paper, an embedded half-bridge Z-source inverter based on gamma structure is proposed. In contrast with the classical half-bridge inverter, the proposed inverter can generate zero voltage levels in output. High voltage gain and low voltage stress on capacitors are the main advantages of the proposed converter. The value of the boost factor in the proposed structure is increased by changing both the shoot-through (ST) duty cycle and turns ratio of the transformer. The operating principle of the proposed converter in four operating modes is presented. We also calculate the critical inductance and compare the proposed converter with conventional topologies. In addition, power loss and THD analysis are presented. Finally, PSCAD/EMTDC software is used to verify the correct operation of the proposed inverter and the experimental results.
- Open Access
- 9 January 2020
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 13 (4) , 680-692
Double‐fed and double‐switch active Z‐source inverter with general variable high boost factor
In this study, a new topology for Z‐source inverter is proposed without adding additional passive elements to the conventional impedance network. The proposed topology is double‐fed and can generate high voltage gain in comparison with the conventional Z‐source inverters. By using improved simple boost modulation technique, the function of boost factor in the proposed inverter is general and variable. In other words, not only the boost factor of the proposed inverter depends on value of shoot‐through (ST) duty cycle but also is dependent on the value of switching factor and controllable by changing specific signals in switching pattern. In this study, steady‐state analysis of the proposed inverter in different operating modes such as ST operating mode, adjacent‐non‐ST (A‐nST) operating mode and non‐A‐nST operating mode are presented. Design considerations and critical inductance between proper and improper operations are calculated. Then, the used modulation technique and switching pattern are investigated and comparison between the proposed and conventional inverters from different points of view is done. Finally, simulation results using PSCAD/EMTDC software and experimental results are presented to verify theoretical discussions, derived equations and correct operation of the proposed inverter.
- 9 January 2020
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 13 (4) , 680-692
Open AccessDouble‐fed and double‐switch active Z‐source inverter with general variable high boost factor
In this study, a new topology for Z‐source inverter is proposed without adding additional passive elements to the conventional impedance network. The proposed topology is double‐fed and can generate high voltage gain in comparison with the conventional Z‐source inverters. By using improved simple boost modulation technique, the function of boost factor in the proposed inverter is general and variable. In other words, not only the boost factor of the proposed inverter depends on value of shoot‐through (ST) duty cycle but also is dependent on the value of switching factor and controllable by changing specific signals in switching pattern. In this study, steady‐state analysis of the proposed inverter in different operating modes such as ST operating mode, adjacent‐non‐ST (A‐nST) operating mode and non‐A‐nST operating mode are presented. Design considerations and critical inductance between proper and improper operations are calculated. Then, the used modulation technique and switching pattern are investigated and comparison between the proposed and conventional inverters from different points of view is done. Finally, simulation results using PSCAD/EMTDC software and experimental results are presented to verify theoretical discussions, derived equations and correct operation of the proposed inverter.
- 7 November 2019
- Published by World Scientific Pub Co Pte Ltd in Journal of Circuits, Systems and Computers
- Vol. 29 (09)
Markov Chain Modeling for Reliability Analysis of Multi-Phase Buck Converters
In recent years, the structure of multi-phase buck converter also called Interleaved Buck Converter (IBC) has gained considerable attention. The advantages of the IBC in comparison to the conventional Buck converter (CBC) are the lower output current ripple, higher efficiency, fast transient response, lower electromagnetic interference and higher reliability. Since more than one stage is employed in the IBC, this converter is highly reliable. In this paper, the reliability and mean time to failure (MTTF) of the CBC, and two- and three-stage IBCs are figured out. Using the obtained results and considering various scenarios, a comprehensive comparison is provided. In addition, the operation of the converter in case of fault occurrence for high and low capacities is analyzed and reliability is evaluated in each state. The relation between the reliability and temperature of semiconductor elements is discussed. Furthermore, a laboratory-scaled prototype is used to extract the experimental results of the temperature variation of the elements during a fault. Markov model is used to evaluate the analyzed reliability.
- 7 November 2019
- Published by World Scientific Pub Co Pte Ltd in Journal of Circuits, Systems and Computers
- Vol. 29 (09)
Markov Chain Modeling for Reliability Analysis of Multi-Phase Buck Converters
In recent years, the structure of multi-phase buck converter also called Interleaved Buck Converter (IBC) has gained considerable attention. The advantages of the IBC in comparison to the conventional Buck converter (CBC) are the lower output current ripple, higher efficiency, fast transient response, lower electromagnetic interference and higher reliability. Since more than one stage is employed in the IBC, this converter is highly reliable. In this paper, the reliability and mean time to failure (MTTF) of the CBC, and two- and three-stage IBCs are figured out. Using the obtained results and considering various scenarios, a comprehensive comparison is provided. In addition, the operation of the converter in case of fault occurrence for high and low capacities is analyzed and reliability is evaluated in each state. The relation between the reliability and temperature of semiconductor elements is discussed. Furthermore, a laboratory-scaled prototype is used to extract the experimental results of the temperature variation of the elements during a fault. Markov model is used to evaluate the analyzed reliability.
- 12 June 2019
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 12 (7) , 1616-1633
Switched Z‐source networks: a review
This study reviews and categorises different structures of switched Z‐source networks. Generally, these structures are divided into two groups of basic switched Z‐source networks and switched Z‐source networks with the capability of high boost. Each of these groups is divided into several subgroups and different structures are introduced. For each subsection, the general power circuit is proposed and the extraction method from general power circuit for each structure is obtained. This study also provides a complete analysis of structures by using a conventional control method with two shoot‐through and non‐shoot‐through modes. Small signal analysis for structures with a basic switched Z‐source network is conducted and the general signal flow graph is extracted. A comprehensive analysis of all structures with a switched Z‐source network is done and the tree diagram for the division of these structures is provided. Finally, different industrial applications and outlook of Z‐source networks are introduced.
- 12 June 2019
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 12 (7) , 1616-1633
Switched Z‐source networks: a review
This study reviews and categorises different structures of switched Z‐source networks. Generally, these structures are divided into two groups of basic switched Z‐source networks and switched Z‐source networks with the capability of high boost. Each of these groups is divided into several subgroups and different structures are introduced. For each subsection, the general power circuit is proposed and the extraction method from general power circuit for each structure is obtained. This study also provides a complete analysis of structures by using a conventional control method with two shoot‐through and non‐shoot‐through modes. Small signal analysis for structures with a basic switched Z‐source network is conducted and the general signal flow graph is extracted. A comprehensive analysis of all structures with a switched Z‐source network is done and the tree diagram for the division of these structures is provided. Finally, different industrial applications and outlook of Z‐source networks are introduced.