Abhishek Kumar Jha
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Abhishek Kumar Jha has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Michal Mrozowski
Faculty of Electronics, Telecommunications, and Informatics, Gdask University of Technology, Gdansk, Poland
6 shared publications - Mohammad Jaleel Akhtar
IIT Kanpur
6 shared publications - Nilesh Kumar Tiwari
Department of Electrical Engineering, Indian Institute of Technology Kanpur, Kanpur, Uttar Pradesh, India
6 shared publications - Adam Lamecki
Faculty of Electronics, Telecommunications, and Informatics, Gdask University of Technology, Gdask, Poland
5 shared publications - Zubair Akhter
Department of Electrical Engineering, King Abdullah University of Science and Technology, Thuwal, Saudi Arabia
4 shared publications - Maurizio Bozzi
University of Pavia, Pavia, Italy
3 shared publications
Latest Publications
- 8 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 75 (00189456) , 8004910
High-Sensitivity Displacement Detection Employing Stepped-Impedance Microstrip Line Coupled Dielectric Resonator Interrogated by a Single-Frequency Reflectometer
This paper presents the design, optimization, fabrication, and experimental validation of a highly sensitive linear displacement sensor based on a cylindrical dielectric resonator (CDR) loaded on an open-ended stepped-impedance microstrip transmission line. The proposed sensor demonstrates a novel approach for achieving a sensitivity of 100 dB/mm over the 0–0.5 mm displacement range by employing a compact, fixed-frequency, reflection-mode architecture, representing the highest reported sensitivity among existing single-frequency sensors in the literature. The operational flexibility of the proposed sensor lies in its fixed-frequency (narrow-band), variable |S11| magnitude operation, which permits the use of a low-cost measurement system in place of a costly vector network analyzer (VNA). This advantage is demonstrated in this paper through validation with a low-cost reflectometer setup.
- 8 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 75 (00189456) , 8004910
High-Sensitivity Displacement Detection Employing Stepped-Impedance Microstrip Line Coupled Dielectric Resonator Interrogated by a Single-Frequency Reflectometer
This paper presents the design, optimization, fabrication, and experimental validation of a highly sensitive linear displacement sensor based on a cylindrical dielectric resonator (CDR) loaded on an open-ended stepped-impedance microstrip transmission line. The proposed sensor demonstrates a novel approach for achieving a sensitivity of 100 dB/mm over the 0–0.5 mm displacement range by employing a compact, fixed-frequency, reflection-mode architecture, representing the highest reported sensitivity among existing single-frequency sensors in the literature. The operational flexibility of the proposed sensor lies in its fixed-frequency (narrow-band), variable |S11| magnitude operation, which permits the use of a low-cost measurement system in place of a costly vector network analyzer (VNA). This advantage is demonstrated in this paper through validation with a low-cost reflectometer setup.
- 22 September 2025
- Published by Elsevier in Fusion Engineering and Design
- Vol. 222
Cavity design and interaction computation of a tri-frequency 42-85-94 GHz gyrotron
- 22 September 2025
- Published by Elsevier in Fusion Engineering and Design
- Vol. 222
Cavity design and interaction computation of a tri-frequency 42-85-94 GHz gyrotron
- 5 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 53 (10) , 2913-2919
Advanced Design Studies of Key Components for a Triple-Frequency 42-/84-/95-GHz Gyrotron Output System
This article presents the design, simulation, and optimization of the key components of an advanced output system for a triple-frequency gyrotron operating at 42 GHz (TE ${}_{\textbf {6,2}}$ ), 84 GHz (TE ${}_{\textbf {10,4}}$ ), and 95 GHz (TE ${}_{\textbf {12,4}}$ ). The gyrotron generates the output power up to 200 kW at the desired frequencies with efficiency exceeding 40%, suitable for various applications in thermonuclear fusion reactors, including plasma start-up, current drive, and RF heating. Key components include a nonlinear taper (NLT), a quasi-optical launcher (QOL), a sapphire Brewster window, and a matching optics unit (MOU). The geometry of these components is optimized using the in-house tool package Gyrotron Design Studio (GDS V. 2024). In addition, commercial packages, Launcher Optimization Tool (LOT) and Surf3D, are used for designing QOL. Gaussian mode content factors of the output beams from the launcher are greater than 98% for all frequencies. The sapphire Brewster window enhances beam transport efficiency, while the MOU, featuring two beam-shaping mirrors, ensures optimal beam quality and effective coupling of the Gaussian beam to the corrugated waveguide. This study demonstrates the successful application of advanced design and optimization methods, using both proprietary and commercial simulation tools to achieve a high-performance output system for the triple-frequency gyrotron.
- 5 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 53 (10) , 2913-2919
Advanced Design Studies of Key Components for a Triple-Frequency 42-/84-/95-GHz Gyrotron Output System
This article presents the design, simulation, and optimization of the key components of an advanced output system for a triple-frequency gyrotron operating at 42 GHz (TE ${}_{\textbf {6,2}}$ ), 84 GHz (TE ${}_{\textbf {10,4}}$ ), and 95 GHz (TE ${}_{\textbf {12,4}}$ ). The gyrotron generates the output power up to 200 kW at the desired frequencies with efficiency exceeding 40%, suitable for various applications in thermonuclear fusion reactors, including plasma start-up, current drive, and RF heating. Key components include a nonlinear taper (NLT), a quasi-optical launcher (QOL), a sapphire Brewster window, and a matching optics unit (MOU). The geometry of these components is optimized using the in-house tool package Gyrotron Design Studio (GDS V. 2024). In addition, commercial packages, Launcher Optimization Tool (LOT) and Surf3D, are used for designing QOL. Gaussian mode content factors of the output beams from the launcher are greater than 98% for all frequencies. The sapphire Brewster window enhances beam transport efficiency, while the MOU, featuring two beam-shaping mirrors, ensures optimal beam quality and effective coupling of the Gaussian beam to the corrugated waveguide. This study demonstrates the successful application of advanced design and optimization methods, using both proprietary and commercial simulation tools to achieve a high-performance output system for the triple-frequency gyrotron.
- Open Access
- 30 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Internet of Things Journal
- Vol. 12 (15) , 31891-31906
IoT-Driven Regression Tree Models for Efficient Microwave Dielectric Material Characterization: Addressing Non-Linear Cavity Sensing
Interconnected microwave dielectric sensing nodes have the potential to revolutionize microwave material processing and design, where microwave dielectric materials characterization (MDMC) with high precision and rapid circuit design are crucial. This research presents an Internet of Things (IoT)-enabled automated MDMC system designed to tackle the nonlinearity challenges in the extended cavity perturbation regime. Utilizing a cylindrical cavity operating in TE111 mode at 5 GHz, the proposed MDMC system is extensively trained on a diverse range of materials through numerous full-wave 3-D electromagnetic simulations. The outputs, i.e., relative permittivity and loss tangent, are derived using advanced machine learning models, including decision tree (DT) and ensemble learning (EL). A comparative analysis that incorporates simulation, measurement, and predicted permittivity values across varying sample dimensions demonstrates the robustness and accuracy of the DT and EL model. This validates the effectiveness of our high-quality sensor node and sophisticated data processing techniques within an IoT-centric framework.
- 30 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Internet of Things Journal
- Vol. 12 (15) , 31891-31906
Open AccessIoT-Driven Regression Tree Models for Efficient Microwave Dielectric Material Characterization: Addressing Non-Linear Cavity Sensing
Interconnected microwave dielectric sensing nodes have the potential to revolutionize microwave material processing and design, where microwave dielectric materials characterization (MDMC) with high precision and rapid circuit design are crucial. This research presents an Internet of Things (IoT)-enabled automated MDMC system designed to tackle the nonlinearity challenges in the extended cavity perturbation regime. Utilizing a cylindrical cavity operating in TE111 mode at 5 GHz, the proposed MDMC system is extensively trained on a diverse range of materials through numerous full-wave 3-D electromagnetic simulations. The outputs, i.e., relative permittivity and loss tangent, are derived using advanced machine learning models, including decision tree (DT) and ensemble learning (EL). A comparative analysis that incorporates simulation, measurement, and predicted permittivity values across varying sample dimensions demonstrates the robustness and accuracy of the DT and EL model. This validates the effectiveness of our high-quality sensor node and sophisticated data processing techniques within an IoT-centric framework.
- 20 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (8) , 3508-3516
Revisiting Toroidal Dipolar Moment in Planar Metamaterial
This article revisits the electric, magnetic, and toroidal dipolar moments in the metamaterial structure and presents the flatland design for generating a toroidal dipolar response for the electromagnetic plane wave at normal incidence. Based on the numerical analysis of the surface current, the electric field, the magnetic field, and the quantitative analysis of scattered power supported by the electromagnetic multipole theory, it is shown that the earlier design involving symmetric unit cells is not able to produce toroidal dipolar moment. This study resulted in a new design of a planar metasurface, which provides a toroidal response as the dominant mode when excited by the transverse magnetic (TM)-polarized electromagnetic wave. The scattered power calculated for the proposed toroidal flatland metamaterial is found to be 1.7 $\times$ 10 $^{5}$ times larger than the earlier design under investigation. The scattered power due to the toroidal dipole in the proposed design is found to be at least 70 times and 8 $\times$ 10 $^{8}$ times larger than the electric dipole and the magnetic dipole, respectively, in the $z$ -direction.
- 20 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (8) , 3508-3516
Revisiting Toroidal Dipolar Moment in Planar Metamaterial
This article revisits the electric, magnetic, and toroidal dipolar moments in the metamaterial structure and presents the flatland design for generating a toroidal dipolar response for the electromagnetic plane wave at normal incidence. Based on the numerical analysis of the surface current, the electric field, the magnetic field, and the quantitative analysis of scattered power supported by the electromagnetic multipole theory, it is shown that the earlier design involving symmetric unit cells is not able to produce toroidal dipolar moment. This study resulted in a new design of a planar metasurface, which provides a toroidal response as the dominant mode when excited by the transverse magnetic (TM)-polarized electromagnetic wave. The scattered power calculated for the proposed toroidal flatland metamaterial is found to be 1.7 $\times$ 10 $^{5}$ times larger than the earlier design under investigation. The scattered power due to the toroidal dipole in the proposed design is found to be at least 70 times and 8 $\times$ 10 $^{8}$ times larger than the electric dipole and the magnetic dipole, respectively, in the $z$ -direction.
- 4 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (5) , 2159-2168
Near-Field Wireless Sensing of Plastics and Papers Using Frugal Peel-Off Passive Tag
This article presents a novel frugal approach of testing plastics and papers using a near-field microwave sensing technique with a peel-off tag. The proposed sensing technique involves two electrical entities: the sensor, which may be regarded as a reader, and a disposable tag. The reader is a modified design of a gap-coupled microstrip line (GCML) sensor, while the passive tag is a standard double-ring complementary split-ring resonator (CSRR) engraved on a commercially available copper foil using laser printing techniques. A detailed numerical study is presented for the engineered sensing methodology, showing the effect of the sample height, sensing distance, bending angle, and inclination. Empirical formulas associated with the dielectric properties of the sample under test are also given. The errors associated with a possible air gap between the peel-off tag and the sample, as well as the relative positioning of the tag and the reader, are analyzed while also considering the bending of the tag. Finally, the sensor is fabricated on a 1.5-mm-thick Rogers RT5880 laminate, and several standard samples are prepared to experimentally check the validity of the approach. The sensor provides a transmission bandwidth (BW) of 1.9 GHz with a typical insertion loss (IL) of 1 dB and a reflection loss of 20 dB. The tag engraved on the frugal peel-off copper foil is used for sensing various dielectric materials by placing it on planar and curved surfaces. The simulation and measured results are found to be in close agreement. The proposed scheme is found to be reliable and cost-effective also for the testing of microwave substrates. It provides robust results for the wireless sensing of objects located within a range of 10 mm from the reader.
- 4 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (5) , 2159-2168
Near-Field Wireless Sensing of Plastics and Papers Using Frugal Peel-Off Passive Tag
This article presents a novel frugal approach of testing plastics and papers using a near-field microwave sensing technique with a peel-off tag. The proposed sensing technique involves two electrical entities: the sensor, which may be regarded as a reader, and a disposable tag. The reader is a modified design of a gap-coupled microstrip line (GCML) sensor, while the passive tag is a standard double-ring complementary split-ring resonator (CSRR) engraved on a commercially available copper foil using laser printing techniques. A detailed numerical study is presented for the engineered sensing methodology, showing the effect of the sample height, sensing distance, bending angle, and inclination. Empirical formulas associated with the dielectric properties of the sample under test are also given. The errors associated with a possible air gap between the peel-off tag and the sample, as well as the relative positioning of the tag and the reader, are analyzed while also considering the bending of the tag. Finally, the sensor is fabricated on a 1.5-mm-thick Rogers RT5880 laminate, and several standard samples are prepared to experimentally check the validity of the approach. The sensor provides a transmission bandwidth (BW) of 1.9 GHz with a typical insertion loss (IL) of 1 dB and a reflection loss of 20 dB. The tag engraved on the frugal peel-off copper foil is used for sensing various dielectric materials by placing it on planar and curved surfaces. The simulation and measured results are found to be in close agreement. The proposed scheme is found to be reliable and cost-effective also for the testing of microwave substrates. It provides robust results for the wireless sensing of objects located within a range of 10 mm from the reader.
- Open Access
- 27 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 121632-121644
Characteristics Modeling of GaN Class-AB Dual-Band PA Under Different Temperature and Humidity Conditions
As the technology scales down, besides the CAD tools and design guidelines, understanding circuit performance degradation as a consequence of transistor degradation becomes essential for designers. Due to several adverse environmental conditions, the study of performance degradation in the power amplifier (PA) is very demanding research. In this paper, an RF PA is experimentally studied to observe various characteristic degradations in a broad range of operating temperature and humidity conditions. Based on a few key measurement points, a measurement-based modeling method is proposed to help designers make intelligent decisions to minimize the performance degradation effects. This method uses four two-dimensional interpolation models, and the results show that the prediction results of the four planar interpolation models are in good agreement with the measurement results. The results presented in this article help select design models for the RF power amplifier that can analyze the performance degradation of the transistor parameters in advance. Cubic and spline interpolation has the highest model accuracy among the four two-dimensional models, while the nearest interpolation offers the shortest training time.
- 27 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 121632-121644
Open AccessCharacteristics Modeling of GaN Class-AB Dual-Band PA Under Different Temperature and Humidity Conditions
As the technology scales down, besides the CAD tools and design guidelines, understanding circuit performance degradation as a consequence of transistor degradation becomes essential for designers. Due to several adverse environmental conditions, the study of performance degradation in the power amplifier (PA) is very demanding research. In this paper, an RF PA is experimentally studied to observe various characteristic degradations in a broad range of operating temperature and humidity conditions. Based on a few key measurement points, a measurement-based modeling method is proposed to help designers make intelligent decisions to minimize the performance degradation effects. This method uses four two-dimensional interpolation models, and the results show that the prediction results of the four planar interpolation models are in good agreement with the measurement results. The results presented in this article help select design models for the RF power amplifier that can analyze the performance degradation of the transistor parameters in advance. Cubic and spline interpolation has the highest model accuracy among the four two-dimensional models, while the nearest interpolation offers the shortest training time.
- 23 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (8) , 3759-3769
Extending the Frequency Limit of Microstrip-Coupled CSRR Using Asymmetry
This article explains the frequency limitation in designing microstrip circuits based on a complementary split-ring resonator (CSRR) and reports a novel technique for increasing its operating frequency, which makes the CSRR suitable for high-frequency applications. This study helps in synthesizing the dimensions of symmetric CSRR (SCSRR) and asymmetric CSRR (ACSRR) circuits, which shows the applicability of the proposed technique in designing mm-wave circuits. It is observed that the upper frequency limit of the microstrip-coupled SCSRR is mainly due to weak electric coupling. The weak coupling implicates radiation loss in the structure, and the frequency at which the SCSRR has maximum loss due to radiation is found to be much less than the cutoff frequency of the higher order mode of the microstrip line, thus effectively limiting the operating frequency range of the circuit. In this article, the type of coupling and associated electrical parameters, e.g., reflected power, transmitted power, radiated power, losses, quality factor, voltage standing wave ratio, and gain, are investigated in detail. The allowable bandwidth of the fundamental mode of the microstrip line can be utilized to design CSRR with improved coupling. It is found that the ACSRR enhances the coupling coefficient using the cross-coupling effect. At higher frequencies, where the electric coupling is becoming too weak for the SCSRR, it is possible to design a magnetically coupled ACSRR of the same dimensions as the SCSRR. Finally, the design profile for both the SCSRR and ACSRR is studied in detail, and the radiating condition is discussed as a function of the height and dielectric constant of the substrate. For practical-verification purposes, two circuit prototypes are fabricated on a 1.5-mm-thick Rogers RT5880 substrate, and the measured results are found to be in good agreement with the proposition. It is found that, for a given microwave substrate, the maximum allowable resonating frequency of the ACSRR structure is nearly twice that of the SCSRR structure.
- 23 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (8) , 3759-3769
Extending the Frequency Limit of Microstrip-Coupled CSRR Using Asymmetry
This article explains the frequency limitation in designing microstrip circuits based on a complementary split-ring resonator (CSRR) and reports a novel technique for increasing its operating frequency, which makes the CSRR suitable for high-frequency applications. This study helps in synthesizing the dimensions of symmetric CSRR (SCSRR) and asymmetric CSRR (ACSRR) circuits, which shows the applicability of the proposed technique in designing mm-wave circuits. It is observed that the upper frequency limit of the microstrip-coupled SCSRR is mainly due to weak electric coupling. The weak coupling implicates radiation loss in the structure, and the frequency at which the SCSRR has maximum loss due to radiation is found to be much less than the cutoff frequency of the higher order mode of the microstrip line, thus effectively limiting the operating frequency range of the circuit. In this article, the type of coupling and associated electrical parameters, e.g., reflected power, transmitted power, radiated power, losses, quality factor, voltage standing wave ratio, and gain, are investigated in detail. The allowable bandwidth of the fundamental mode of the microstrip line can be utilized to design CSRR with improved coupling. It is found that the ACSRR enhances the coupling coefficient using the cross-coupling effect. At higher frequencies, where the electric coupling is becoming too weak for the SCSRR, it is possible to design a magnetically coupled ACSRR of the same dimensions as the SCSRR. Finally, the design profile for both the SCSRR and ACSRR is studied in detail, and the radiating condition is discussed as a function of the height and dielectric constant of the substrate. For practical-verification purposes, two circuit prototypes are fabricated on a 1.5-mm-thick Rogers RT5880 substrate, and the measured results are found to be in good agreement with the proposition. It is found that, for a given microwave substrate, the maximum allowable resonating frequency of the ACSRR structure is nearly twice that of the SCSRR structure.
- 15 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 70 (00189456) , 1-10
Accurate Microwave Cavity Sensing Technique for Dielectric Testing of Arbitrary Length Samples
In this article, an attractive resonant technique is devised for calculating the dielectric properties of arbitrary length material under test (ALMUT), which is partially filled inside a waveguide cavity sensor. The proposed technique exempts two major assumptions viz. the depolarization effect and the theory of images, which were neglected in earlier cavity perturbation methods. A numerical model of the depolarizing factor, which precisely considers the impact of the relative permittivity and the sinusoidal variation of the electric field, is also formulated. First, the technical modification and the numerical analysis are provided and after that, a new set of formulas for characterizing the complex permittivity of ALMUT is developed. The numerical results suggest the accuracy and validity of the scheme for a broad range of dielectric samples, including the typical case, i.e., the full-length dielectric sample. The novelty of the presented technique can be ascertained from the fact that it provides higher accuracy irrespective of the actual sample length when compared with standard cavity techniques. A few standard dielectric samples with the partially filled arrangement are measured using the WR90 cavity, and the results are compared with their corresponding values obtained using the earlier reported conventional and modified techniques. It is found that the results evaluated using the devised scheme are consistent and independent of the actual dimensions of ALMUT. On the other hand, error in estimated complex permittivity using the earlier reported approaches shows substantial dependence on the sample size.
- 15 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 70 (00189456) , 1-10
Accurate Microwave Cavity Sensing Technique for Dielectric Testing of Arbitrary Length Samples
In this article, an attractive resonant technique is devised for calculating the dielectric properties of arbitrary length material under test (ALMUT), which is partially filled inside a waveguide cavity sensor. The proposed technique exempts two major assumptions viz. the depolarization effect and the theory of images, which were neglected in earlier cavity perturbation methods. A numerical model of the depolarizing factor, which precisely considers the impact of the relative permittivity and the sinusoidal variation of the electric field, is also formulated. First, the technical modification and the numerical analysis are provided and after that, a new set of formulas for characterizing the complex permittivity of ALMUT is developed. The numerical results suggest the accuracy and validity of the scheme for a broad range of dielectric samples, including the typical case, i.e., the full-length dielectric sample. The novelty of the presented technique can be ascertained from the fact that it provides higher accuracy irrespective of the actual sample length when compared with standard cavity techniques. A few standard dielectric samples with the partially filled arrangement are measured using the WR90 cavity, and the results are compared with their corresponding values obtained using the earlier reported conventional and modified techniques. It is found that the results evaluated using the devised scheme are consistent and independent of the actual dimensions of ALMUT. On the other hand, error in estimated complex permittivity using the earlier reported approaches shows substantial dependence on the sample size.
- 16 February 2021
- Published by Springer Nature
- p. 123-151
Epsilon-Near-Zero Microwave Sensors