Adam B. Price
Research Subjects
Adam B. Price has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Jason T. DeJong
University of California
4 shared publications - Ross W. Boulanger
Univ. of California, Davis
4 shared publications A. M. Parra Bastidas
1 shared publication- Ana Maria Parra Bastidas
Projects Engineer, Carlos H. Parra and Associates, Calle 8 N° 16-80, Cali 760008, Colombia. ORCID:
1 shared publication D. Moug
1 shared publicationDiane M. Moug
Assistant Professor, Dept. of Civil and Environmental Engineering, Portland State Univ., Portland, OR 95701
1 shared publication
Latest Publications
- 1 November 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 145 (11)
Centrifuge Modeling of Variable-Rate Cone Penetration in Low-Plasticity Silts
The effects of soil plasticity and penetration rate on cone penetration resistance in low-plasticity fine-grained soils are evaluated. A series of centrifuge tests with in-flight variable rate cone penetration soundings was performed on models of four slurry deposited mixtures of nonplastic silica silt and kaolin clay (0%, 2.5%, 5%, and 20% kaolin by dry mass) with plasticity indices ranging from 0 to 6. Cone penetration resistances for an effective overburden stress of 100 kPa ranged from 26 to 40 MPa (260 to 400 atm) in the nonplastic silica silt to 0.4–1.8 MPa (4–18 atm) in the silt-clay mixture with a plasticity index of 6. The addition of a small amount of clay (as little as 2.5% by dry mass) to nonplastic silt resulted in an order of magnitude decrease in drained penetration resistance. Faster penetration rates produced partially drained and undrained conditions, with negative excess pore pressures developing in the nonplastic silica silt and positive excess pore pressures developing in the mixtures with 5% and 20% kaolin.
- 1 November 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 145 (11)
Centrifuge Modeling of Variable-Rate Cone Penetration in Low-Plasticity Silts
The effects of soil plasticity and penetration rate on cone penetration resistance in low-plasticity fine-grained soils are evaluated. A series of centrifuge tests with in-flight variable rate cone penetration soundings was performed on models of four slurry deposited mixtures of nonplastic silica silt and kaolin clay (0%, 2.5%, 5%, and 20% kaolin by dry mass) with plasticity indices ranging from 0 to 6. Cone penetration resistances for an effective overburden stress of 100 kPa ranged from 26 to 40 MPa (260 to 400 atm) in the nonplastic silica silt to 0.4–1.8 MPa (4–18 atm) in the silt-clay mixture with a plasticity index of 6. The addition of a small amount of clay (as little as 2.5% by dry mass) to nonplastic silt resulted in an order of magnitude decrease in drained penetration resistance. Faster penetration rates produced partially drained and undrained conditions, with negative excess pore pressures developing in the nonplastic silica silt and positive excess pore pressures developing in the mixtures with 5% and 20% kaolin.
- 1 October 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 145 (10)
Mechanistic Development of CPT-Based Cyclic Strength Correlations for Clean Sand
- 1 October 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 145 (10)
Mechanistic Development of CPT-Based Cyclic Strength Correlations for Clean Sand
- 1 October 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 143 (10)
Cyclic Loading Response of Silt with Multiple Loading Events
The evolution of cyclic resistance with multiple loading events is evaluated for nonplastic and low-plasticity silts with plasticity indices of 0 and 6, respectively. A series of direct simple shear tests with multiple cyclic loading and reconsolidation stages is performed on young slurry-sedimented specimens. Evolution of cyclic strength with a series of multiple loading events is examined with respect to densification from postcyclic reconsolidation, shear strain–induced fabric, and initial consolidation history. Initially normally consolidated specimens of both silts develop progressive increases in cyclic strength with prior strain history, with cyclic resistance ratios ultimately exceeding 0.6. Specimens consolidated with an initial overconsolidation ratio of 2 experience an 18–32% loss of cyclic strength following the first stage of cyclic shearing and reconsolidation. The two silts develop similar magnitudes of reconsolidation strain, but the low-plasticity silt requires more volumetric strain (and therefore more loading events) to develop large cyclic strengths. Implications for future advances in liquefaction triggering correlations and engineering practice are discussed.
- 1 October 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 143 (10)
Cyclic Loading Response of Silt with Multiple Loading Events
The evolution of cyclic resistance with multiple loading events is evaluated for nonplastic and low-plasticity silts with plasticity indices of 0 and 6, respectively. A series of direct simple shear tests with multiple cyclic loading and reconsolidation stages is performed on young slurry-sedimented specimens. Evolution of cyclic strength with a series of multiple loading events is examined with respect to densification from postcyclic reconsolidation, shear strain–induced fabric, and initial consolidation history. Initially normally consolidated specimens of both silts develop progressive increases in cyclic strength with prior strain history, with cyclic resistance ratios ultimately exceeding 0.6. Specimens consolidated with an initial overconsolidation ratio of 2 experience an 18–32% loss of cyclic strength following the first stage of cyclic shearing and reconsolidation. The two silts develop similar magnitudes of reconsolidation strain, but the low-plasticity silt requires more volumetric strain (and therefore more loading events) to develop large cyclic strengths. Implications for future advances in liquefaction triggering correlations and engineering practice are discussed.
- 8 February 2016
- Published by American Society of Civil Engineers (ASCE)
Effect of Prior Strain History on the Cyclic Strength and CPT Penetration Resistance of Silica Silt
The effect of prior strain history on cyclic strength and cone penetration test (CPT) tip resistance of non-plastic silica silt is evaluated. A series of undrained cyclic direct simple shear (DSS) tests on slurry deposited specimens are performed to characterize cyclic strength. Cyclic strengths are evaluated for maximum shear strains of 1% and 3% in 15 cycles. Drained CPT tip resistances are estimated from simulated cavity expansion limit pressures. Cylindrical cavity expansion simulations are performed in the finite difference program FLAC using a modified version of the MIT-S1 elasto-plastic constitutive model. The evolution of cyclic strength and simulated CPT tip resistance during a series of cyclic loading and reconsolidation stages is presented. The developed relationships between cyclic strength and CPT tip resistance are shown to track the curvature of corresponding semi-empirical qc1Ncs-CRR triggering curves. Dependence of the presented relationships on failure criterion (maximum shear strain) is shown to be qualitatively consistent with the literature.
- 8 February 2016
- Published by American Society of Civil Engineers (ASCE)
Effect of Prior Strain History on the Cyclic Strength and CPT Penetration Resistance of Silica Silt
The effect of prior strain history on cyclic strength and cone penetration test (CPT) tip resistance of non-plastic silica silt is evaluated. A series of undrained cyclic direct simple shear (DSS) tests on slurry deposited specimens are performed to characterize cyclic strength. Cyclic strengths are evaluated for maximum shear strains of 1% and 3% in 15 cycles. Drained CPT tip resistances are estimated from simulated cavity expansion limit pressures. Cylindrical cavity expansion simulations are performed in the finite difference program FLAC using a modified version of the MIT-S1 elasto-plastic constitutive model. The evolution of cyclic strength and simulated CPT tip resistance during a series of cyclic loading and reconsolidation stages is presented. The developed relationships between cyclic strength and CPT tip resistance are shown to track the curvature of corresponding semi-empirical qc1Ncs-CRR triggering curves. Dependence of the presented relationships on failure criterion (maximum shear strain) is shown to be qualitatively consistent with the literature.