Ravi Bathe
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Ravi Bathe has a total of 128 co-authors. Here are the top co-authors by number of shared publications:
S. I. Patil
University of Pune Centre for Advanced Studies in Solid State Physics and Materials Science, Department of Physics Pune 411 007, India
12 shared publicationsS. B. Ogale
Center for Superconductivity Research, Department of Physics, University of Maryland, College Park, Maryland 20742
9 shared publicationsG. K. Mehta
Nuclear Science Center, Aruna Asaf Ali Marg, New Delhi 110 067, India
5 shared publicationsG. Padmanabham
International Advanced Research Centre for Powder Metallurgy and New Materials (ARCI) 1 , Balapur Post, Hyderabad 500005
5 shared publicationsS. K. Date
University of Pune Centre for Advanced Studies in Solid State Physics and Materials Science, Department of Physics Pune 411 007, India
5 shared publicationsT. Venkatesan
Center for Superconductivity Research, Department of Physics, University of Maryland, College Park, Maryland 20742
5 shared publications
Latest Publications
- 21 October 2026
- Published by SAGE Publications in Powder Metallurgy
Investigation of process parameters of laser powder bed fusion to manufacture crack-free M2 high-speed steel
This study detailed the optimisation of process parameters for the laser powder bed fusion (LPBF) additive manufacturing process to produce crack-free, high-density M2 high-speed steel alloy. The high carbon content of this steel increases its susceptibility to cracking under the steep thermal gradients of the LPBF process. The work identifies optimised processing parameters for manufacturing defect-free M2 high-speed steel with minimal residual stress. A matrix of samples was built by varying laser power and scan speed, under 180°C platform heating. It was found that there are three distinct sample behaviours, categorised by volumetric energy density (VED): build failure at high energy density, macro-cracking at intermediate energy density and sound but porous structures at low energy density. X-ray diffraction analysis of cracked samples revealed phase transformations with varying VED, suggesting that the thermal gradient played a significant role in crack formation. While analysing the set of samples without visible macro-cracking, a critical VED of 27 J/mm 3 was identified, resulting in a crack-free sample when using a relatively low power (225 W) and low speed (1000 mm/s) combination, which reduces thermal stress. Using this optimal baseline, the process was further refined by adjusting the laser hatch distance. Decreasing the hatch distance from 140 µm to 120 µm successfully minimised internal porosity by promoting ideal melt pool overlap. The optimised process yielded fully dense, crack-free parts with a relative density of 99.38% (8.11 g.cm −3 ) and an as-built hardness of 643 HV0.5.
- 21 October 2026
- Published by SAGE Publications in Powder Metallurgy
Investigation of process parameters of laser powder bed fusion to manufacture crack-free M2 high-speed steel
This study detailed the optimisation of process parameters for the laser powder bed fusion (LPBF) additive manufacturing process to produce crack-free, high-density M2 high-speed steel alloy. The high carbon content of this steel increases its susceptibility to cracking under the steep thermal gradients of the LPBF process. The work identifies optimised processing parameters for manufacturing defect-free M2 high-speed steel with minimal residual stress. A matrix of samples was built by varying laser power and scan speed, under 180°C platform heating. It was found that there are three distinct sample behaviours, categorised by volumetric energy density (VED): build failure at high energy density, macro-cracking at intermediate energy density and sound but porous structures at low energy density. X-ray diffraction analysis of cracked samples revealed phase transformations with varying VED, suggesting that the thermal gradient played a significant role in crack formation. While analysing the set of samples without visible macro-cracking, a critical VED of 27 J/mm 3 was identified, resulting in a crack-free sample when using a relatively low power (225 W) and low speed (1000 mm/s) combination, which reduces thermal stress. Using this optimal baseline, the process was further refined by adjusting the laser hatch distance. Decreasing the hatch distance from 140 µm to 120 µm successfully minimised internal porosity by promoting ideal melt pool overlap. The optimised process yielded fully dense, crack-free parts with a relative density of 99.38% (8.11 g.cm −3 ) and an as-built hardness of 643 HV0.5.
- 2 March 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
Performance evaluation of uncoated and CrAlSiN nanocomposite coated tungsten carbide tools in conventional and Laser-assisted turning of inconel-625
The expansion in nuclear, aerospace, and automotive sectors surged the demand for high-temperature materials like Inconel-625. These materials are difficult-to-machine due to their high strength, low thermal diffusivity, and work-hardening properties. The surface finish, dimensional accuracy, and material removal rates achieved in traditional machining processes are marginal and require frequent tool changes due to high tool-wear, resulting in low productivity and elevated machining costs. Thus, there is a need for new and alternative hybrid manufacturing processes to be developed for machining hard-to-cut materials, which are highly efficient, eco-friendly, and sustainable. Laser-assisted machining, which emerged as a new and advanced hybrid thermal-assisted machining technology, has proven to enhance the machinability of difficult-to-cut materials over the decades. The present study investigates the tool-life of CrAlSiN nanocomposite-coated and uncoated tungsten carbide tools in conventional and laser-assisted turning of Inconel-625 according to ISO-3685 standard. The results showed a 40% and 160% increase in tool-life for uncoated tools and CrAlSiN-coated tools, respectively, in laser-assisted turning compared to conventional turning of Inconel-625 in similar conditions.
- 2 March 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
Performance evaluation of uncoated and CrAlSiN nanocomposite coated tungsten carbide tools in conventional and Laser-assisted turning of inconel-625
The expansion in nuclear, aerospace, and automotive sectors surged the demand for high-temperature materials like Inconel-625. These materials are difficult-to-machine due to their high strength, low thermal diffusivity, and work-hardening properties. The surface finish, dimensional accuracy, and material removal rates achieved in traditional machining processes are marginal and require frequent tool changes due to high tool-wear, resulting in low productivity and elevated machining costs. Thus, there is a need for new and alternative hybrid manufacturing processes to be developed for machining hard-to-cut materials, which are highly efficient, eco-friendly, and sustainable. Laser-assisted machining, which emerged as a new and advanced hybrid thermal-assisted machining technology, has proven to enhance the machinability of difficult-to-cut materials over the decades. The present study investigates the tool-life of CrAlSiN nanocomposite-coated and uncoated tungsten carbide tools in conventional and laser-assisted turning of Inconel-625 according to ISO-3685 standard. The results showed a 40% and 160% increase in tool-life for uncoated tools and CrAlSiN-coated tools, respectively, in laser-assisted turning compared to conventional turning of Inconel-625 in similar conditions.
- 19 May 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (2) , 025424
Precision ultrafast laser micromachining of silicon microfluidic channels
This study investigates the micromachining of microchannels on silicon surfaces using a femtosecond pulsed laser with an 800 nm wavelength and 100 fs pulse duration. The process parameters were modeled and optimized using the Response Surface Methodology based on the Box-Behnken design to enhance machining precision and efficiency. The effects of laser power, scanning speed, and line spacing on depth, surface roughness, and material removal rate were systematically evaluated. Results showed that higher laser power (up to 750 mW) significantly increased MRR, whereas lower power (e.g., 50 mW) reduced material removal. Scanning speed inversely affected machined depth, while line spacing (5–15 μm) strongly influenced machining outcomes through parameter interactions. The highest material removal rate of 1.18 × 106 μm3 s−1 was achieved under optimized conditions. Validation experiments confirmed the accuracy of the response surface methodology model, with optimized parameters (310 mW laser power, 10 mm s−1 scanning speed, and 5 μm line spacing) yielding a machined depth of 10 μm and surface roughness of 0.4 μm. Precise and thermally damage-free microchannels were successfully fabricated, demonstrating the effectiveness of this methodology for advanced silicon micromachining applications.
- 19 May 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (2) , 025424
Precision ultrafast laser micromachining of silicon microfluidic channels
This study investigates the micromachining of microchannels on silicon surfaces using a femtosecond pulsed laser with an 800 nm wavelength and 100 fs pulse duration. The process parameters were modeled and optimized using the Response Surface Methodology based on the Box-Behnken design to enhance machining precision and efficiency. The effects of laser power, scanning speed, and line spacing on depth, surface roughness, and material removal rate were systematically evaluated. Results showed that higher laser power (up to 750 mW) significantly increased MRR, whereas lower power (e.g., 50 mW) reduced material removal. Scanning speed inversely affected machined depth, while line spacing (5–15 μm) strongly influenced machining outcomes through parameter interactions. The highest material removal rate of 1.18 × 106 μm3 s−1 was achieved under optimized conditions. Validation experiments confirmed the accuracy of the response surface methodology model, with optimized parameters (310 mW laser power, 10 mm s−1 scanning speed, and 5 μm line spacing) yielding a machined depth of 10 μm and surface roughness of 0.4 μm. Precise and thermally damage-free microchannels were successfully fabricated, demonstrating the effectiveness of this methodology for advanced silicon micromachining applications.
- 3 March 2025
- Published by IOP Publishing in Physica Scripta
- Vol. 100 (4) , 045901
Investigations on the frictional performance of laser surface textured piston rings in an automotive engine test rig under different coolant and lubricant temperature
Research in the field of internal combustion engines is currently focussed on two primary objectives: improving fuel efficiency and reducing emissions. A significant portion of this research is directed towards addressing frictional losses, which account for 40% of the total energy dissipation in a typical engine and holds the potential to substantially enhance fuel economy. Within the scope of this study, we have identified the application of micro-geometric patterns on piston rings as a promising technology for mitigating friction between the piston rings and cylinder liners. Additionally, our findings reveal that the utilization of textured rings in engines led to a remarkable reduction in lubricant oil consumption, approximately 12.35%. The key factors contributing to this reduction include the uniform distribution of surface textures and the viscosity-driven flow of oil within the contact surfaces, particularly under the conditions of boundary lubrication. These factors collectively exert a notable influence on engine performance.
- 3 March 2025
- Published by IOP Publishing in Physica Scripta
- Vol. 100 (4) , 045901
Investigations on the frictional performance of laser surface textured piston rings in an automotive engine test rig under different coolant and lubricant temperature
Research in the field of internal combustion engines is currently focussed on two primary objectives: improving fuel efficiency and reducing emissions. A significant portion of this research is directed towards addressing frictional losses, which account for 40% of the total energy dissipation in a typical engine and holds the potential to substantially enhance fuel economy. Within the scope of this study, we have identified the application of micro-geometric patterns on piston rings as a promising technology for mitigating friction between the piston rings and cylinder liners. Additionally, our findings reveal that the utilization of textured rings in engines led to a remarkable reduction in lubricant oil consumption, approximately 12.35%. The key factors contributing to this reduction include the uniform distribution of surface textures and the viscosity-driven flow of oil within the contact surfaces, particularly under the conditions of boundary lubrication. These factors collectively exert a notable influence on engine performance.
- 30 January 2025
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 142 (16)
Micromachining of Intricate Microchannels on the Polycarbonate Using Ultrafast Laser Ablation
Ultrafast laser processing enables the fabrication of microscale structures in diverse materials without inducing heat‐affected zones. The ablation and micromachining properties of polycarbonate were investigated using a femtosecond‐pulsed laser with an 800 nm wavelength and a 100 fs pulse duration. Ablation threshold fluence was determined to be 0.0112 J/cm2. Response Surface Methodology based on the Box–Behnken design was applied for the optimization of the conditions of the micromachining process with respect to laser pulse energy, scanning speed, and line spacing. An increased rate of material removal by a higher laser power of 800 mW decreased in the case of the lower power of 100 mW. Line spacing became very critical because while varying from 5 to 15 μm, it resulted in a different machining pattern. An increased scanning speed decreased the machined depth. The highest material removal rate achieved is reported as 4.9 × 106 μm3/s under optimum conditions. Intricate microchannels with accurate dimensions fabricated in a polycarbonate disk have been ensured to have no or very minimal thermal damage. The results obtained have significant relevance to present useful information on precision micromachining of polycarbonate with huge potential for developing polymer‐based microdevices.
- 30 January 2025
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 142 (16)
Micromachining of Intricate Microchannels on the Polycarbonate Using Ultrafast Laser Ablation
Ultrafast laser processing enables the fabrication of microscale structures in diverse materials without inducing heat‐affected zones. The ablation and micromachining properties of polycarbonate were investigated using a femtosecond‐pulsed laser with an 800 nm wavelength and a 100 fs pulse duration. Ablation threshold fluence was determined to be 0.0112 J/cm2. Response Surface Methodology based on the Box–Behnken design was applied for the optimization of the conditions of the micromachining process with respect to laser pulse energy, scanning speed, and line spacing. An increased rate of material removal by a higher laser power of 800 mW decreased in the case of the lower power of 100 mW. Line spacing became very critical because while varying from 5 to 15 μm, it resulted in a different machining pattern. An increased scanning speed decreased the machined depth. The highest material removal rate achieved is reported as 4.9 × 106 μm3/s under optimum conditions. Intricate microchannels with accurate dimensions fabricated in a polycarbonate disk have been ensured to have no or very minimal thermal damage. The results obtained have significant relevance to present useful information on precision micromachining of polycarbonate with huge potential for developing polymer‐based microdevices.
- 12 September 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 240 (3) , 3293-3305
Investigations on laser-assisted turning of IN625 alloy with hot hardness approach using uncoated and CrAlSiN coated WC tools
This paper presents an investigation into the effect of laser-assisted turning of the IN625 superalloy using uncoated and CrAlSiN nanocomposite-coated tungsten carbide tools. A hot hardness test was conducted for IN625 material, which showed there was a pronounced softening of the material above 850 °C. This exercise guided the choice of laser power for the subsequent laser-assisted turning experiments. The cutting forces (radial/thrust, F x ; axial/feed, F y ; and tangential/cutting, F z ), maximum flank wear (VB Bmax ), and surface roughness ( R a ) were measured and analyzed for the planned experiments. The results demonstrated that at 2500 W laser power, a 9%, 70%, and 59% reduction of cutting forces for uncoated tools, and a 31%, 77%, and 69% reduction for CrAlSiN coated tools were observed in the F x , F y , and F z directions respectively. At 2250 W laser power, the uncoated tools exhibited a 33% (433–289 µm) reduction in VB Bmax and a 28% (1.8–1.3 µm) reduction in Ra . The CrAlSiN-coated tools, at 2500 W laser power, showed even more significant improvements, with reductions of 46% (365–232 µm) in VB Bmax and 56% (1.4–0.8 µm) in R a . The results underline the improved performance of laser-assisted turning for cutting-force and tool-wear reduction and improved surface finish with CrAlSiN-coated tools. This paper presents the potential of laser-assisted machining as a viable method for machining difficult-to-machine materials like IN625, which offers enormous manufacturing productivity and tool life benefits.
- 12 September 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 240 (3) , 3293-3305
Investigations on laser-assisted turning of IN625 alloy with hot hardness approach using uncoated and CrAlSiN coated WC tools
This paper presents an investigation into the effect of laser-assisted turning of the IN625 superalloy using uncoated and CrAlSiN nanocomposite-coated tungsten carbide tools. A hot hardness test was conducted for IN625 material, which showed there was a pronounced softening of the material above 850 °C. This exercise guided the choice of laser power for the subsequent laser-assisted turning experiments. The cutting forces (radial/thrust, F x ; axial/feed, F y ; and tangential/cutting, F z ), maximum flank wear (VB Bmax ), and surface roughness ( R a ) were measured and analyzed for the planned experiments. The results demonstrated that at 2500 W laser power, a 9%, 70%, and 59% reduction of cutting forces for uncoated tools, and a 31%, 77%, and 69% reduction for CrAlSiN coated tools were observed in the F x , F y , and F z directions respectively. At 2250 W laser power, the uncoated tools exhibited a 33% (433–289 µm) reduction in VB Bmax and a 28% (1.8–1.3 µm) reduction in Ra . The CrAlSiN-coated tools, at 2500 W laser power, showed even more significant improvements, with reductions of 46% (365–232 µm) in VB Bmax and 56% (1.4–0.8 µm) in R a . The results underline the improved performance of laser-assisted turning for cutting-force and tool-wear reduction and improved surface finish with CrAlSiN-coated tools. This paper presents the potential of laser-assisted machining as a viable method for machining difficult-to-machine materials like IN625, which offers enormous manufacturing productivity and tool life benefits.
- 25 July 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (11) , 9878-9887
Enhancing Tribological Performance of Gray Cast Iron by Laser Surface Texturing of Micro-grooves and Micro-crosshatches
- 25 July 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (11) , 9878-9887
Enhancing Tribological Performance of Gray Cast Iron by Laser Surface Texturing of Micro-grooves and Micro-crosshatches
- 6 May 2024
- Published by Elsevier in Tribology International
- Vol. 197, 109711
Laser surface structuring of titanium alloy (Ti-6Al-4V) for improved tribocorrosion resistance for bio-implant applications
- 6 May 2024
- Published by Elsevier in Tribology International
- Vol. 197, 109711
Laser surface structuring of titanium alloy (Ti-6Al-4V) for improved tribocorrosion resistance for bio-implant applications