Pramod Reddy
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Pramod Reddy has a total of 170 co-authors. Here are the top co-authors by number of shared publications:
Ronny Kirste
Adroit Materials, Inc
49 shared publicationsSeiji Mita
Adroit Materials, Inc
40 shared publicationsRamon Collazo
37 shared publicationsZlatko Sitar
North Carolina State University
36 shared publications- Zlatko Sitar
Department of Materials Science and Engineering, North Carolina State University 1 , Raleigh, North Carolina 27606
36 shared publications Ramón Collazo
Department of Materials Science and Engineering, North Carolina State University, Raleigh, North Carolina 27695, United States
28 shared publications
Latest Publications
- 28 September 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 140 (12)
High hole concentration in Mg-doped GaN achieved by controlling compensation
Over an order of magnitude increase in the maximum attainable hole concentration in Mg-doped GaN was achieved by managing the nitrogen chemical potential during growth to suppress the formation of compensating point defect complexes. A semi-empirical model was developed that quantitatively describes the observed behavior and suggests the dominant compensating defects are nitrogen vacancy—Mg complexes.
- 28 September 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 140 (12)
High hole concentration in Mg-doped GaN achieved by controlling compensation
Over an order of magnitude increase in the maximum attainable hole concentration in Mg-doped GaN was achieved by managing the nitrogen chemical potential during growth to suppress the formation of compensating point defect complexes. A semi-empirical model was developed that quantitatively describes the observed behavior and suggests the dominant compensating defects are nitrogen vacancy—Mg complexes.
- 14 September 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (11)
Surface-catalyzed decomposition of ammonia in MOCVD growth of III-nitrides
The amount of ammonia available at the growth surface during metalorganic chemical vapor deposition of III-nitrides differs significantly from the reactor input. It depends not only on reactor design but also on the properties of the growth surface. To predict the surface chemical potentials and the kinetics governing growth, we developed a quantitative model that incorporates catalytic decomposition reactions at the surface. Our results show that, depending on surface polarity and carrier gas, at least two orders of magnitude more ammonia is lost through decomposition than is incorporated into growth. Decomposition is particularly pronounced for N-polar surfaces when nitrogen is used as the carrier gas. This model enables prediction and control of surface morphology, as well as the incorporation of point defects.
- 14 September 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (11)
Surface-catalyzed decomposition of ammonia in MOCVD growth of III-nitrides
The amount of ammonia available at the growth surface during metalorganic chemical vapor deposition of III-nitrides differs significantly from the reactor input. It depends not only on reactor design but also on the properties of the growth surface. To predict the surface chemical potentials and the kinetics governing growth, we developed a quantitative model that incorporates catalytic decomposition reactions at the surface. Our results show that, depending on surface polarity and carrier gas, at least two orders of magnitude more ammonia is lost through decomposition than is incorporated into growth. Decomposition is particularly pronounced for N-polar surfaces when nitrogen is used as the carrier gas. This model enables prediction and control of surface morphology, as well as the incorporation of point defects.
- 15 June 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (24)
High sub-bandgap response and fast switching enabled by thermal quenching in carbon-doped semi-insulating GaN
Carbon-doped GaN is a promising material for sub-bandgap triggered optical switches. When incorporated in GaN, carbon introduces deep compensating centers that enable defect-mediated extrinsic photoconductivity. Here, we investigate the optical responsivity and switching kinetics of semi-insulating carbon-doped GaN actuated by sub-bandgap blue illumination. A high ON/OFF ratio exceeding 107 is achieved under low-irradiance 405-nm excitation. Temperature-dependent transient measurements reveal that the photocurrent decay is thermally quenched above a crossover temperature of ∼300 K. This behavior is attributed to hole-emission-assisted recombination. The extracted activation energies vary across samples; a commonly observed value of ∼0.83 eV is attributed to the CN defect. Notably, when heating above the crossover temperature, thermal quenching accelerates the photocurrent decay by up to a factor of five, enabling significantly faster switching.
- 15 June 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (24)
High sub-bandgap response and fast switching enabled by thermal quenching in carbon-doped semi-insulating GaN
Carbon-doped GaN is a promising material for sub-bandgap triggered optical switches. When incorporated in GaN, carbon introduces deep compensating centers that enable defect-mediated extrinsic photoconductivity. Here, we investigate the optical responsivity and switching kinetics of semi-insulating carbon-doped GaN actuated by sub-bandgap blue illumination. A high ON/OFF ratio exceeding 107 is achieved under low-irradiance 405-nm excitation. Temperature-dependent transient measurements reveal that the photocurrent decay is thermally quenched above a crossover temperature of ∼300 K. This behavior is attributed to hole-emission-assisted recombination. The extracted activation energies vary across samples; a commonly observed value of ∼0.83 eV is attributed to the CN defect. Notably, when heating above the crossover temperature, thermal quenching accelerates the photocurrent decay by up to a factor of five, enabling significantly faster switching.
- Open Access
- 24 February 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 139 (8)
Enabling the growth of thick, relaxed AlGaN films on bulk GaN substrates
Epitaxial growth of thick, relaxed, homogeneous, and crack-free AlGaN films was demonstrated on single-crystalline GaN substrates. A maskless heteroepitaxial facet-controlled epitaxial lateral overgrowth (FACELO) scheme was developed to relax the lattice mismatch-induced tensile stress via the generation and glide of misfit dislocations at the pyramidal heterointerfaces. Up to 10 μm-thick AlGaN films were demonstrated, which was more than three orders of magnitude beyond the critical thickness for cracking. The expected relaxation mechanism was confirmed by the observation of misfit dislocations at the heterointerfaces via transmission electron microscopy. The developed growth scheme is amenable to the growth of thick, homogeneous, relaxed AlGaN films of any composition on native substrates.
- 24 February 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 139 (8)
Open AccessEnabling the growth of thick, relaxed AlGaN films on bulk GaN substrates
Epitaxial growth of thick, relaxed, homogeneous, and crack-free AlGaN films was demonstrated on single-crystalline GaN substrates. A maskless heteroepitaxial facet-controlled epitaxial lateral overgrowth (FACELO) scheme was developed to relax the lattice mismatch-induced tensile stress via the generation and glide of misfit dislocations at the pyramidal heterointerfaces. Up to 10 μm-thick AlGaN films were demonstrated, which was more than three orders of magnitude beyond the critical thickness for cracking. The expected relaxation mechanism was confirmed by the observation of misfit dislocations at the heterointerfaces via transmission electron microscopy. The developed growth scheme is amenable to the growth of thick, homogeneous, relaxed AlGaN films of any composition on native substrates.
- Open Access
- 18 February 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 139 (7)
Hole transport analysis in N-polar p-GaN
The transport-limiting scattering mechanisms in N-polar p-GaN were identified over a wide range of temperatures (220–770 K), Mg doping concentrations (3 × 1018–4 × 1019 cm−3), and V/III ratios (100–8000). Temperature-dependent Hall measurements, combined with a charge balance model, were employed to extract the acceptor (NA) and donor (ND) concentrations. These values enabled the determination of the temperature-dependent Hall factor (rH), allowing the conversion of the measured Hall mobility (μHall) to drift mobility (μdrift). The experimental drift mobility was then fitted using a mobility model, which incorporates six scattering mechanisms, including coulomb scattering by charged dislocation lines. The model identified charged dislocation scattering as the transport-limiting scattering mechanism at both room and low temperatures. The origin of coulomb scattering—donor-like traps along threading edge dislocations—was attributed to charged nitrogen vacancy-related defects [(VN−nMgGa)3−n, where n = 0, 1, or 2], with their concentration controllable through [Mg] and the nitrogen chemical potential (i.e., V/III ratio).
- 18 February 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 139 (7)
Open AccessHole transport analysis in N-polar p-GaN
The transport-limiting scattering mechanisms in N-polar p-GaN were identified over a wide range of temperatures (220–770 K), Mg doping concentrations (3 × 1018–4 × 1019 cm−3), and V/III ratios (100–8000). Temperature-dependent Hall measurements, combined with a charge balance model, were employed to extract the acceptor (NA) and donor (ND) concentrations. These values enabled the determination of the temperature-dependent Hall factor (rH), allowing the conversion of the measured Hall mobility (μHall) to drift mobility (μdrift). The experimental drift mobility was then fitted using a mobility model, which incorporates six scattering mechanisms, including coulomb scattering by charged dislocation lines. The model identified charged dislocation scattering as the transport-limiting scattering mechanism at both room and low temperatures. The origin of coulomb scattering—donor-like traps along threading edge dislocations—was attributed to charged nitrogen vacancy-related defects [(VN−nMgGa)3−n, where n = 0, 1, or 2], with their concentration controllable through [Mg] and the nitrogen chemical potential (i.e., V/III ratio).
- Top Cited Papers
- 12 January 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (2)
High-current, high-voltage AlN p–n junction diodes enabled by compositional grading
AlN p–n junction diodes with low specific ON-resistance (1.6 mΩ cm2), enabling forward current densities >1 kA/cm2, and reverse breakdown fields of 8 MV/cm, were demonstrated. The quasi-vertical device structure consisted of a p-AlGaN anode, an n-AlN drift layer, and an n-AlGaN back contact. The effect of the AlGaN/AlN band offset was studied by comparing devices with abrupt and compositionally graded junctions. Simulation and experimental data suggested that the valence band offset at the abrupt junction significantly limited hole injection into the AlN, limiting the forward current. This problem was mitigated with the use of a compositionally graded junction that showed an order of magnitude higher ON-state current density. These results show that high-current, high-breakdown AlN p–n junction diodes can be achieved by using compositional grading to circumvent the doping problem in p-type AlN.
- 12 January 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (2)
Top Cited PapersHigh-current, high-voltage AlN p–n junction diodes enabled by compositional grading
AlN p–n junction diodes with low specific ON-resistance (1.6 mΩ cm2), enabling forward current densities >1 kA/cm2, and reverse breakdown fields of 8 MV/cm, were demonstrated. The quasi-vertical device structure consisted of a p-AlGaN anode, an n-AlN drift layer, and an n-AlGaN back contact. The effect of the AlGaN/AlN band offset was studied by comparing devices with abrupt and compositionally graded junctions. Simulation and experimental data suggested that the valence band offset at the abrupt junction significantly limited hole injection into the AlN, limiting the forward current. This problem was mitigated with the use of a compositionally graded junction that showed an order of magnitude higher ON-state current density. These results show that high-current, high-breakdown AlN p–n junction diodes can be achieved by using compositional grading to circumvent the doping problem in p-type AlN.
- 15 December 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (24)
On the origin of carrier loss in Mg-doped N-polar GaN
The neutral (VN-3MgGa)0 complex was found to be the primary compensator in Mg-doped N-polar GaN. The experimental data showed a sharp drop in hole concentration once [Mg] exceeded ∼1019 cm−3. Temperature-dependent Hall measurements, in conjunction with a charge balance model, revealed that the carrier loss was due to a drastic reduction in acceptor concentration (NA), suggesting that a significant fraction of Mg atoms was incorporated in an electrically neutral configuration. A quantitative semi-empirical model based on the grand canonical formalism pointed to the formation of (VN-3MgGa)0 complexes as the primary cause for the observed carrier loss.
- 15 December 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (24)
On the origin of carrier loss in Mg-doped N-polar GaN
The neutral (VN-3MgGa)0 complex was found to be the primary compensator in Mg-doped N-polar GaN. The experimental data showed a sharp drop in hole concentration once [Mg] exceeded ∼1019 cm−3. Temperature-dependent Hall measurements, in conjunction with a charge balance model, revealed that the carrier loss was due to a drastic reduction in acceptor concentration (NA), suggesting that a significant fraction of Mg atoms was incorporated in an electrically neutral configuration. A quantitative semi-empirical model based on the grand canonical formalism pointed to the formation of (VN-3MgGa)0 complexes as the primary cause for the observed carrier loss.
- 11 January 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 135 (2)
Dissolution of Mg-enriched defects in implanted GaN and increased p-type dopant activation
Annealing Mg-implanted homoepitaxial GaN at temperatures above 1400 °C eliminates the formation of inversion domains and leads to improved dopant activation efficiency. Extended defects, in the form of inversion domains, contain electrically inactive Mg after post-implantation annealing at temperatures as high as 1300 °C (one GPa N2 overpressure), which results in a low dopant activation efficiency. Triple-axis x-ray data reveal that implant-induced strain is fully relieved after annealing at 1300 °C for 10 min, indicating that strain-inducing point defects formed during implantation have reconfigured and inversion domains are formed. However, annealing at temperatures of 1400–1500 °C (one GPa N2 overpressure) eliminates the presence of the inversion domains. While residual defects, such as dislocation loops, still exist after annealing at and above 1400 °C, chemical analysis at multiple dislocation loops shows no sign of Mg segregation. Meanwhile, an overall decreasing trend in the dislocation loop density is observed after annealing at the higher temperatures and longer times. Additionally, once inversion domains are formed and the samples are cooled to room temperature, they are shown to dissolve with subsequent annealing above 1400 °C. While such defects have been observed before, the important finding that such defects can be dissolved with a short, higher temperature step is key. Earlier work [Breckenridge et al., J. Appl. Phys. Lett. 118, 022101 (2021)] addressing electrical measurements of these types of samples showed that annealing at 1400 °C leads to a dopant activation efficiency that is an order of magnitude higher than that observed at 1300 °C. This work complements earlier work by identifying the inversion domains, which incorporate Mg, and points to the benefits, in terms of defect density and p-type dopant activation, of using higher temperature (>1400 °C) annealing cycles to activate Mg in GaN, even if the Mg-containing inversion domains had been formed during lower temperature annealing.
- 11 January 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 135 (2)
Dissolution of Mg-enriched defects in implanted GaN and increased p-type dopant activation
Annealing Mg-implanted homoepitaxial GaN at temperatures above 1400 °C eliminates the formation of inversion domains and leads to improved dopant activation efficiency. Extended defects, in the form of inversion domains, contain electrically inactive Mg after post-implantation annealing at temperatures as high as 1300 °C (one GPa N2 overpressure), which results in a low dopant activation efficiency. Triple-axis x-ray data reveal that implant-induced strain is fully relieved after annealing at 1300 °C for 10 min, indicating that strain-inducing point defects formed during implantation have reconfigured and inversion domains are formed. However, annealing at temperatures of 1400–1500 °C (one GPa N2 overpressure) eliminates the presence of the inversion domains. While residual defects, such as dislocation loops, still exist after annealing at and above 1400 °C, chemical analysis at multiple dislocation loops shows no sign of Mg segregation. Meanwhile, an overall decreasing trend in the dislocation loop density is observed after annealing at the higher temperatures and longer times. Additionally, once inversion domains are formed and the samples are cooled to room temperature, they are shown to dissolve with subsequent annealing above 1400 °C. While such defects have been observed before, the important finding that such defects can be dissolved with a short, higher temperature step is key. Earlier work [Breckenridge et al., J. Appl. Phys. Lett. 118, 022101 (2021)] addressing electrical measurements of these types of samples showed that annealing at 1400 °C leads to a dopant activation efficiency that is an order of magnitude higher than that observed at 1300 °C. This work complements earlier work by identifying the inversion domains, which incorporate Mg, and points to the benefits, in terms of defect density and p-type dopant activation, of using higher temperature (>1400 °C) annealing cycles to activate Mg in GaN, even if the Mg-containing inversion domains had been formed during lower temperature annealing.
- 12 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (3) , 1494-1501
Analysis of Vertical GaN JBS and p-n Diodes by Mg Ion Implantation and Ultrahigh-Pressure Annealing
We report on vertical GaN junction barrier Schottky (JBS) diodes formed by Mg ion implantation and ultrahigh -pressure annealing (UHPA). The static ON-state characteristics of the diodes show an ideality factor of 1.05, a turn-on voltage of $\sim$ 0.7 V, a current rectification ratio of $\sim$ 10 $^{11}$ , and a low differential specific ON-resistance that scales with Schottky stripe width in fair agreement with the analytical model. The reverse leakage dependence on Schottky stripe width also agrees well with the analytical model. Implanted p-n junction diodes fabricated on the same wafer exhibit avalanche breakdown in reverse bias with a positive temperature coefficient, but the forward current is limited by a series barrier. Temperature-dependent current–voltage measurements of th p-n diodes verify the presence of the implanted p-n junction and reveal an additional 0.43-eV barrier, which we hypothesize arises from a p-Schottky contact and forms a second diode back-to-back with the p-n junction. This interpretation is supported by analysis of the capacitance–voltage characteristics of the implanted p-n diodes, epitaxial p-n diodes fabricated with intentional p-Schottky contacts, and comparison to TCAD simulations. Ultimately, the presence of the p-Schottky contact does not hinder JBS diode operation. The use of diffusion-aware designs and/or diffusion reduction represents future directions for Mg implantation technology in GaN power devices.
- 12 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (3) , 1494-1501
Analysis of Vertical GaN JBS and p-n Diodes by Mg Ion Implantation and Ultrahigh-Pressure Annealing
We report on vertical GaN junction barrier Schottky (JBS) diodes formed by Mg ion implantation and ultrahigh -pressure annealing (UHPA). The static ON-state characteristics of the diodes show an ideality factor of 1.05, a turn-on voltage of $\sim$ 0.7 V, a current rectification ratio of $\sim$ 10 $^{11}$ , and a low differential specific ON-resistance that scales with Schottky stripe width in fair agreement with the analytical model. The reverse leakage dependence on Schottky stripe width also agrees well with the analytical model. Implanted p-n junction diodes fabricated on the same wafer exhibit avalanche breakdown in reverse bias with a positive temperature coefficient, but the forward current is limited by a series barrier. Temperature-dependent current–voltage measurements of th p-n diodes verify the presence of the implanted p-n junction and reveal an additional 0.43-eV barrier, which we hypothesize arises from a p-Schottky contact and forms a second diode back-to-back with the p-n junction. This interpretation is supported by analysis of the capacitance–voltage characteristics of the implanted p-n diodes, epitaxial p-n diodes fabricated with intentional p-Schottky contacts, and comparison to TCAD simulations. Ultimately, the presence of the p-Schottky contact does not hinder JBS diode operation. The use of diffusion-aware designs and/or diffusion reduction represents future directions for Mg implantation technology in GaN power devices.