DPDario Papale

Dario Papale

*This is an algorithmically generated author record based on publicly available information.

Dario Papale has a total of 1000 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Fluxes Everywhere, All of the Time—A Tribute to Dennis Baldocchi

    by Youngryel Ryu, Eva Falge, Trevor Keenan, Sara Knox, Dario Papale, Markus Reichstein

  • Open Access

    Spectral versus co-spectral correction of eddy-covariance fluxes: a multi-site assessment across the ICOS network

    by Ariane Faurès, Gerardo Fratini, Giacomo Nicolini, Dario Papale, Simone Sabbatini, Bernard Heinesch

    Accurate correction of high-frequency attenuation remains a critical challenge in eddy-covariance measurements of turbulent gas fluxes. Experimental correction approaches based on either power spectra or co-spectra are widely used, yet their relative behaviour and implications for flux estimates have not been systematically assessed across sites and atmospheric conditions. This study presents a multi-site comparison of these two approaches using one year of CO 2 and H 2 O flux data from 38 ecosystem stations of the Integrated Carbon Observation System (ICOS) equipped with a standardized enclosed-path gas analyser setup. To support reproducibility and facilitate future methodological intercomparisons, we additionally provide an open-source and configurable software tool implementing both correction approaches. Overall, the ICOS setup exhibited limited high-frequency attenuation, with correction factors generally below 1.2 for CO 2 and occasionally approaching 2 for H 2 O under humid conditions. For CO 2 , differences between methods remained small after standard turbulence filtering, with cumulative flux differences typically below 2 %. In contrast, H 2 O corrections showed larger discrepancies, frequently reaching 5 %–10 % on cumulative fluxes. The largest differences occurred under stable atmospheric conditions, at low measurement heights, and under strong attenuation. Results indicate that CO 2 attenuation is dominated by sensor-separation effects, whereas H 2 O attenuation is primarily controlled by adsorption–desorption processes within the sampling system. The comparison highlights methodological limitations of both approaches. Both methods rely on assumptions regarding spectral similarity, but departures from these assumptions were found to affect gas spectra much more strongly than co-spectra, particularly for H 2 O under humid conditions. In addition, spectral corrections were frequently affected by high-frequency noise and required dedicated denoising procedures, while sensor-separation effects had to be introduced through analytical formulations. Overall, the co-spectral approach provided more robust and physically consistent results across sites and atmospheric conditions. A comparison with fluxes produced by the ICOS Ecosystem Thematic Centre revealed systematic differences that were often larger than those observed between the spectral and co-spectral approaches themselves, especially for H 2 O. These results demonstrate the effectiveness of setup standardisation across the ICOS network while identifying high-frequency attenuation correction as a remaining source of uncertainty. They also highlight the need for a broader reassessment of this processing step within the ICOS flux-processing pipeline.


  • Open Access

    ABCFlux v2: Arctic–boreal CO 2 and CH 4 monthly flux observations and ancillary information across terrestrial and freshwater ecosystems

    by Anna-Maria Virkkala, Isabel Wargowsky, Judith Vogt, McKenzie A. Kuhn, Simran Madaan, Tiffany Windholz, Kyle A. Arndt, Gerard Rocher-Ros, Mathias Göckede, David Olefeldt, et al.

    Measurements of surface-atmosphere carbon dioxide (CO 2 ) and methane (CH 4 ) fluxes have been relatively sparse across the Arctic tundra and boreal biomes, causing significant uncertainties in carbon budget estimates from the region. While the availability of Arctic-boreal carbon flux data has increased substantially over the past decade, the data have remained spread across different repositories, scientific articles, and unpublished sources, making it difficult to leverage. Here we present a new dataset of monthly Arctic-boreal carbon fluxes (ABCFlux v2) across terrestrial (wetlands and uplands) and freshwater (lakes and rivers) ecosystems compiled from previous syntheses including the Arctic-boreal CO 2 flux database (ABCFlux v1), the Boreal-Arctic Wetland and Lake Methane Dataset (BAWLD-CH4), and the Global River Methane Database (GRiMeDB). In addition, we consider data from general-purpose (e.g., Zenodo) and flux network repositories, literature, and site principal investigators. The dataset includes surface-atmosphere CO 2 fluxes of gross primary production (GPP), ecosystem respiration (Reco), and net ecosystem exchange (NEE), alongside CH 4 fluxes. For aquatic ecosystems, we split CH 4 fluxes into diffusive and ebullitive flux pathways, and included potential emissions from transient storage in the water column (“storage fluxes”), alongside CO 2 and CH 4 concentrations dissolved in the surface water. Fluxes are measured through a variety of methods including chamber and eddy covariance techniques alongside bubble traps, ice-surveys, and concentration-based turbulence-driven modelling in aquatic ecosystems. The monthly flux data are reported together with supporting methodological and environmental metadata. The resulting ABCFlux v2 has 23 847 flux site-months, 8182 concentration site-months, and 199 seasonal observations from 1024 sites, and includes 56 139 reported fluxes (i.e. sum of GPP, Reco, NEE, and CH 4 fluxes) from the years 1984 to 2024. The majority of monthly observations occurred after 1999. Wetlands had the highest number of site-month observations (8758), followed by boreal forest (6981), lotic ecosystems (6275), lentic ecosystems (3799) and upland tundra (3308). Measurements of CO 2 dominated the dataset across most ecosystem types (25 222) except for lentic ecosystems, where CH 4 flux site-months (3098) were more frequent than CO 2 flux site-months (2915). Overall, ABCFlux v2 includes 160 % more site-months for terrestrial CO 2 flux data compared to ABCFlux v1. Integrating and updating BAWLD-CH4 flux data from growing season averages to monthly fluxes resulted in 5671 site-months of chamber CH 4 data compared to 762 site-years. This collaborative initiative, involving contributions from over 260 researchers, provides a comprehensive overview of the current state of the Arctic-boreal carbon flux network and its data, and serves as an important step in reducing uncertainties in Arctic-boreal carbon budgets and in enhancing our understanding of climate feedbacks. The data can be accessed at ORNL DAAC at https://doi.org/10.3334/ORNLDAAC/2448 (Virkkala et al., 2026).


  • Open Access

    Reply on RC2

    by Ariane Faurès, Gerardo Fratini, Giacomo Nicolini, Dario Papale, Simone Sabbatini, Bernard Heinesch

    Accurate correction of high-frequency attenuation remains a critical challenge in eddy-covariance measurements of turbulent gas fluxes. Experimental correction approaches based on either power spectra or co-spectra are widely used, yet their relative behaviour and implications for flux estimates have not been systematically assessed across sites and atmospheric conditions. This study presents a multi-site comparison of these two approaches using one year of CO2 and H2O flux data from 38 ecosystem stations of the Integrated Carbon Observation System (ICOS) equipped with a standardized enclosed-path gas analyser setup. To support reproducibility and facilitate future methodological intercomparisons, we additionally provide an open-source and configurable software tool implementing both correction approaches. Overall, the ICOS setup exhibited limited high-frequency attenuation, with correction factors generally below 1.2 for CO2 and occasionally approaching 2 for H2O under humid conditions. For CO2, differences between methods remained small after standard turbulence filtering, with cumulative flux differences typically below 2 %. In contrast, H2O corrections showed larger discrepancies, frequently reaching 5–10 % on cumulative fluxes. The largest differences occurred under stable atmospheric conditions, at low measurement heights, and under strong attenuation. Results indicate that CO2 attenuation is dominated by sensor-separation effects, whereas H2O attenuation is primarily controlled by adsorption–desorption processes within the sampling system. The comparison highlights methodological limitations of both approaches. Both methods rely on assumptions regarding spectral similarity, but departures from these assumptions were found to affect gas spectra much more strongly than co-spectra, particularly for H2O under humid conditions. In addition, spectral corrections were frequently affected by high-frequency noise and required dedicated denoising procedures, while sensor-separation effects had to be introduced through analytical formulations. Overall, the co-spectral approach provided more robust and physically consistent results across sites and atmospheric conditions. A comparison with fluxes produced by the ICOS Ecosystem Thematic Centre revealed systematic differences that were often larger than those observed between the spectral and co-spectral approaches themselves, especially for H2O. These results demonstrate the effectiveness of setup standardisation across the ICOS network while identifying high-frequency attenuation correction as a remaining source of uncertainty. They also highlight the need for a broader reassessment of this processing step within the ICOS flux-processing pipeline.

  • Open Access

    Reply on RC1

    by Ariane Faurès, Gerardo Fratini, Giacomo Nicolini, Dario Papale, Simone Sabbatini, Bernard Heinesch

    Accurate correction of high-frequency attenuation remains a critical challenge in eddy-covariance measurements of turbulent gas fluxes. Experimental correction approaches based on either power spectra or co-spectra are widely used, yet their relative behaviour and implications for flux estimates have not been systematically assessed across sites and atmospheric conditions. This study presents a multi-site comparison of these two approaches using one year of CO2 and H2O flux data from 38 ecosystem stations of the Integrated Carbon Observation System (ICOS) equipped with a standardized enclosed-path gas analyser setup. To support reproducibility and facilitate future methodological intercomparisons, we additionally provide an open-source and configurable software tool implementing both correction approaches. Overall, the ICOS setup exhibited limited high-frequency attenuation, with correction factors generally below 1.2 for CO2 and occasionally approaching 2 for H2O under humid conditions. For CO2, differences between methods remained small after standard turbulence filtering, with cumulative flux differences typically below 2 %. In contrast, H2O corrections showed larger discrepancies, frequently reaching 5–10 % on cumulative fluxes. The largest differences occurred under stable atmospheric conditions, at low measurement heights, and under strong attenuation. Results indicate that CO2 attenuation is dominated by sensor-separation effects, whereas H2O attenuation is primarily controlled by adsorption–desorption processes within the sampling system. The comparison highlights methodological limitations of both approaches. Both methods rely on assumptions regarding spectral similarity, but departures from these assumptions were found to affect gas spectra much more strongly than co-spectra, particularly for H2O under humid conditions. In addition, spectral corrections were frequently affected by high-frequency noise and required dedicated denoising procedures, while sensor-separation effects had to be introduced through analytical formulations. Overall, the co-spectral approach provided more robust and physically consistent results across sites and atmospheric conditions. A comparison with fluxes produced by the ICOS Ecosystem Thematic Centre revealed systematic differences that were often larger than those observed between the spectral and co-spectral approaches themselves, especially for H2O. These results demonstrate the effectiveness of setup standardisation across the ICOS network while identifying high-frequency attenuation correction as a remaining source of uncertainty. They also highlight the need for a broader reassessment of this processing step within the ICOS flux-processing pipeline.

  • Open Access

    General response to both RCs

    by Ariane Faurès, Gerardo Fratini, Giacomo Nicolini, Dario Papale, Simone Sabbatini, Bernard Heinesch

    Accurate correction of high-frequency attenuation remains a critical challenge in eddy-covariance measurements of turbulent gas fluxes. Experimental correction approaches based on either power spectra or co-spectra are widely used, yet their relative behaviour and implications for flux estimates have not been systematically assessed across sites and atmospheric conditions. This study presents a multi-site comparison of these two approaches using one year of CO2 and H2O flux data from 38 ecosystem stations of the Integrated Carbon Observation System (ICOS) equipped with a standardized enclosed-path gas analyser setup. To support reproducibility and facilitate future methodological intercomparisons, we additionally provide an open-source and configurable software tool implementing both correction approaches. Overall, the ICOS setup exhibited limited high-frequency attenuation, with correction factors generally below 1.2 for CO2 and occasionally approaching 2 for H2O under humid conditions. For CO2, differences between methods remained small after standard turbulence filtering, with cumulative flux differences typically below 2 %. In contrast, H2O corrections showed larger discrepancies, frequently reaching 5–10 % on cumulative fluxes. The largest differences occurred under stable atmospheric conditions, at low measurement heights, and under strong attenuation. Results indicate that CO2 attenuation is dominated by sensor-separation effects, whereas H2O attenuation is primarily controlled by adsorption–desorption processes within the sampling system. The comparison highlights methodological limitations of both approaches. Both methods rely on assumptions regarding spectral similarity, but departures from these assumptions were found to affect gas spectra much more strongly than co-spectra, particularly for H2O under humid conditions. In addition, spectral corrections were frequently affected by high-frequency noise and required dedicated denoising procedures, while sensor-separation effects had to be introduced through analytical formulations. Overall, the co-spectral approach provided more robust and physically consistent results across sites and atmospheric conditions. A comparison with fluxes produced by the ICOS Ecosystem Thematic Centre revealed systematic differences that were often larger than those observed between the spectral and co-spectral approaches themselves, especially for H2O. These results demonstrate the effectiveness of setup standardisation across the ICOS network while identifying high-frequency attenuation correction as a remaining source of uncertainty. They also highlight the need for a broader reassessment of this processing step within the ICOS flux-processing pipeline.

  • Open Access

    General response to both RCs

    by Ariane Faurès, Gerardo Fratini, Giacomo Nicolini, Dario Papale, Simone Sabbatini, Bernard Heinesch

    Accurate correction of high-frequency attenuation remains a critical challenge in eddy-covariance measurements of turbulent gas fluxes. Experimental correction approaches based on either power spectra or co-spectra are widely used, yet their relative behaviour and implications for flux estimates have not been systematically assessed across sites and atmospheric conditions. This study presents a multi-site comparison of these two approaches using one year of CO2 and H2O flux data from 38 ecosystem stations of the Integrated Carbon Observation System (ICOS) equipped with a standardized enclosed-path gas analyser setup. To support reproducibility and facilitate future methodological intercomparisons, we additionally provide an open-source and configurable software tool implementing both correction approaches. Overall, the ICOS setup exhibited limited high-frequency attenuation, with correction factors generally below 1.2 for CO2 and occasionally approaching 2 for H2O under humid conditions. For CO2, differences between methods remained small after standard turbulence filtering, with cumulative flux differences typically below 2 %. In contrast, H2O corrections showed larger discrepancies, frequently reaching 5–10 % on cumulative fluxes. The largest differences occurred under stable atmospheric conditions, at low measurement heights, and under strong attenuation. Results indicate that CO2 attenuation is dominated by sensor-separation effects, whereas H2O attenuation is primarily controlled by adsorption–desorption processes within the sampling system. The comparison highlights methodological limitations of both approaches. Both methods rely on assumptions regarding spectral similarity, but departures from these assumptions were found to affect gas spectra much more strongly than co-spectra, particularly for H2O under humid conditions. In addition, spectral corrections were frequently affected by high-frequency noise and required dedicated denoising procedures, while sensor-separation effects had to be introduced through analytical formulations. Overall, the co-spectral approach provided more robust and physically consistent results across sites and atmospheric conditions. A comparison with fluxes produced by the ICOS Ecosystem Thematic Centre revealed systematic differences that were often larger than those observed between the spectral and co-spectral approaches themselves, especially for H2O. These results demonstrate the effectiveness of setup standardisation across the ICOS network while identifying high-frequency attenuation correction as a remaining source of uncertainty. They also highlight the need for a broader reassessment of this processing step within the ICOS flux-processing pipeline.

  • Open Access

    Comment on egusphere-2026-3465

    by Ariane Faurès, Gerardo Fratini, Giacomo Nicolini, Dario Papale, Simone Sabbatini, Bernard Heinesch

    Accurate correction of high-frequency attenuation remains a critical challenge in eddy-covariance measurements of turbulent gas fluxes. Experimental correction approaches based on either power spectra or co-spectra are widely used, yet their relative behaviour and implications for flux estimates have not been systematically assessed across sites and atmospheric conditions. This study presents a multi-site comparison of these two approaches using one year of CO2 and H2O flux data from 38 ecosystem stations of the Integrated Carbon Observation System (ICOS) equipped with a standardized enclosed-path gas analyser setup. To support reproducibility and facilitate future methodological intercomparisons, we additionally provide an open-source and configurable software tool implementing both correction approaches. Overall, the ICOS setup exhibited limited high-frequency attenuation, with correction factors generally below 1.2 for CO2 and occasionally approaching 2 for H2O under humid conditions. For CO2, differences between methods remained small after standard turbulence filtering, with cumulative flux differences typically below 2 %. In contrast, H2O corrections showed larger discrepancies, frequently reaching 5–10 % on cumulative fluxes. The largest differences occurred under stable atmospheric conditions, at low measurement heights, and under strong attenuation. Results indicate that CO2 attenuation is dominated by sensor-separation effects, whereas H2O attenuation is primarily controlled by adsorption–desorption processes within the sampling system. The comparison highlights methodological limitations of both approaches. Both methods rely on assumptions regarding spectral similarity, but departures from these assumptions were found to affect gas spectra much more strongly than co-spectra, particularly for H2O under humid conditions. In addition, spectral corrections were frequently affected by high-frequency noise and required dedicated denoising procedures, while sensor-separation effects had to be introduced through analytical formulations. Overall, the co-spectral approach provided more robust and physically consistent results across sites and atmospheric conditions. A comparison with fluxes produced by the ICOS Ecosystem Thematic Centre revealed systematic differences that were often larger than those observed between the spectral and co-spectral approaches themselves, especially for H2O. These results demonstrate the effectiveness of setup standardisation across the ICOS network while identifying high-frequency attenuation correction as a remaining source of uncertainty. They also highlight the need for a broader reassessment of this processing step within the ICOS flux-processing pipeline.

  • Open Access

    Comment on egusphere-2026-3465

    by Ariane Faurès, Gerardo Fratini, Giacomo Nicolini, Dario Papale, Simone Sabbatini, Bernard Heinesch

    Accurate correction of high-frequency attenuation remains a critical challenge in eddy-covariance measurements of turbulent gas fluxes. Experimental correction approaches based on either power spectra or co-spectra are widely used, yet their relative behaviour and implications for flux estimates have not been systematically assessed across sites and atmospheric conditions. This study presents a multi-site comparison of these two approaches using one year of CO2 and H2O flux data from 38 ecosystem stations of the Integrated Carbon Observation System (ICOS) equipped with a standardized enclosed-path gas analyser setup. To support reproducibility and facilitate future methodological intercomparisons, we additionally provide an open-source and configurable software tool implementing both correction approaches. Overall, the ICOS setup exhibited limited high-frequency attenuation, with correction factors generally below 1.2 for CO2 and occasionally approaching 2 for H2O under humid conditions. For CO2, differences between methods remained small after standard turbulence filtering, with cumulative flux differences typically below 2 %. In contrast, H2O corrections showed larger discrepancies, frequently reaching 5–10 % on cumulative fluxes. The largest differences occurred under stable atmospheric conditions, at low measurement heights, and under strong attenuation. Results indicate that CO2 attenuation is dominated by sensor-separation effects, whereas H2O attenuation is primarily controlled by adsorption–desorption processes within the sampling system. The comparison highlights methodological limitations of both approaches. Both methods rely on assumptions regarding spectral similarity, but departures from these assumptions were found to affect gas spectra much more strongly than co-spectra, particularly for H2O under humid conditions. In addition, spectral corrections were frequently affected by high-frequency noise and required dedicated denoising procedures, while sensor-separation effects had to be introduced through analytical formulations. Overall, the co-spectral approach provided more robust and physically consistent results across sites and atmospheric conditions. A comparison with fluxes produced by the ICOS Ecosystem Thematic Centre revealed systematic differences that were often larger than those observed between the spectral and co-spectral approaches themselves, especially for H2O. These results demonstrate the effectiveness of setup standardisation across the ICOS network while identifying high-frequency attenuation correction as a remaining source of uncertainty. They also highlight the need for a broader reassessment of this processing step within the ICOS flux-processing pipeline.

  • Open Access

    Spectral versus co-spectral correction of eddy-covariance fluxes: a multi-site assessment across the ICOS network

    by Ariane Faurès, Gerardo Fratini, Giacomo Nicolini, Dario Papale, Simone Sabbatini, Bernard Heinesch

    Accurate correction of high-frequency attenuation remains a critical challenge in eddy-covariance measurements of turbulent gas fluxes. Experimental correction approaches based on either power spectra or co-spectra are widely used, yet their relative behaviour and implications for flux estimates have not been systematically assessed across sites and atmospheric conditions. This study presents a multi-site comparison of these two approaches using one year of CO2 and H2O flux data from 38 ecosystem stations of the Integrated Carbon Observation System (ICOS) equipped with a standardized enclosed-path gas analyser setup. To support reproducibility and facilitate future methodological intercomparisons, we additionally provide an open-source and configurable software tool implementing both correction approaches. Overall, the ICOS setup exhibited limited high-frequency attenuation, with correction factors generally below 1.2 for CO2 and occasionally approaching 2 for H2O under humid conditions. For CO2, differences between methods remained small after standard turbulence filtering, with cumulative flux differences typically below 2 %. In contrast, H2O corrections showed larger discrepancies, frequently reaching 5–10 % on cumulative fluxes. The largest differences occurred under stable atmospheric conditions, at low measurement heights, and under strong attenuation. Results indicate that CO2 attenuation is dominated by sensor-separation effects, whereas H2O attenuation is primarily controlled by adsorption–desorption processes within the sampling system. The comparison highlights methodological limitations of both approaches. Both methods rely on assumptions regarding spectral similarity, but departures from these assumptions were found to affect gas spectra much more strongly than co-spectra, particularly for H2O under humid conditions. In addition, spectral corrections were frequently affected by high-frequency noise and required dedicated denoising procedures, while sensor-separation effects had to be introduced through analytical formulations. Overall, the co-spectral approach provided more robust and physically consistent results across sites and atmospheric conditions. A comparison with fluxes produced by the ICOS Ecosystem Thematic Centre revealed systematic differences that were often larger than those observed between the spectral and co-spectral approaches themselves, especially for H2O. These results demonstrate the effectiveness of setup standardisation across the ICOS network while identifying high-frequency attenuation correction as a remaining source of uncertainty. They also highlight the need for a broader reassessment of this processing step within the ICOS flux-processing pipeline.