Hasan Dilbas
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hasan Dilbas has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Mehmet Şamil Güneş
Yildiz Technical University
5 shared publications - Özgür Çakır
Department of Civil Engineering, Yıldız Technical University
5 shared publications - Furkan Birdal
Civil Engineering Department, Engineering-Architectural Faculty, Kırşehir Ahi Evran University, Kırşehir 40100, Türkiye
4 shared publications Özgür Çakır
4 shared publications- Coşkun Parim
Department of Statistics, Yıldız Technical University, Istanbul, Turkey
3 shared publications - Mucteba Uysal
Yildiz Technical University
3 shared publications
Latest Publications
- 29 October 2026
- Published by Taylor & Francis in Journal of Sustainable Cement-Based Materials
- p. 1-25
Pumice- and fibre-reinforced geopolymer composites: physical, mechanical, durability and fracture mechanics Performance - a critical review
1. The construction industry has been built upon Portland cement-based binder systems over the past century, and today concrete production is held responsible for approximately 5–8% of total anthro...
- 29 October 2026
- Published by Taylor & Francis in Journal of Sustainable Cement-Based Materials
- p. 1-25
Pumice- and fibre-reinforced geopolymer composites: physical, mechanical, durability and fracture mechanics Performance - a critical review
1. The construction industry has been built upon Portland cement-based binder systems over the past century, and today concrete production is held responsible for approximately 5–8% of total anthro...
- Open Access
Development of Sustainable, Thermal-Insulated, and Load-Bearing Material and Modular Infill Wall Elements via 3D-Printed Formwork
Unlike flammable organic insulation, non-combustible inorganic materials offer superior fire safety despite higher thermal conductivity. Recent research focuses on developing innovative, sustainable inorganic solutions using natural and waste-based raw materials. Accordingly, in this study, a thermal insulation material (TIM) design is presented for sustainable buildings. Specifically, white cement, fine and powdered pumice, hydraulic lime were formulated using Response Surface Methodology (RSM) with a Box–Behnken approach. A total of 46 mixtures were produced and cured under ambient conditions for 28 days before undergoing mechanical and physical testing in the experimental phase. ANOVA-validated quadratic models show all mixtures have low densities below 1.2 g/cm3 and porosities of 35.52–39.62%. Optimal Run 23 achieves 11.55 MPa compressive strength, 2.53 MPa bending strength, and 0.25 W/m⋅K thermal conductivity. In addition, 3D-printed modular walls exhibit ductile behavior and maintain structural integrity up to 600 °C. Furthermore, a supplementary assessment of the optimal mixture modified with recycled concrete waste (Run-23+) demonstrated the viability of waste-aggregate integration for improved circular-economy performance. Microstructural analyses via XRD and SEM confirmed the dense formation of calcium silicate hydrate (C–S–H) networks and active pozzolanic reactions. Consequently, the present study demonstrates an advanced composite that combines low density with structural capacity, establishing a novel load-bearing thermal insulation material (LB-TIM). Moreover, by integrating this optimized LB-TIM mixture with custom designed 3D printed formwork technology, this study provides a novel and scalable manufacturing approach for sustainable, thermal-insulated and load-bearing material and modular infill wall elements.
Open AccessDevelopment of Sustainable, Thermal-Insulated, and Load-Bearing Material and Modular Infill Wall Elements via 3D-Printed Formwork
Unlike flammable organic insulation, non-combustible inorganic materials offer superior fire safety despite higher thermal conductivity. Recent research focuses on developing innovative, sustainable inorganic solutions using natural and waste-based raw materials. Accordingly, in this study, a thermal insulation material (TIM) design is presented for sustainable buildings. Specifically, white cement, fine and powdered pumice, hydraulic lime were formulated using Response Surface Methodology (RSM) with a Box–Behnken approach. A total of 46 mixtures were produced and cured under ambient conditions for 28 days before undergoing mechanical and physical testing in the experimental phase. ANOVA-validated quadratic models show all mixtures have low densities below 1.2 g/cm3 and porosities of 35.52–39.62%. Optimal Run 23 achieves 11.55 MPa compressive strength, 2.53 MPa bending strength, and 0.25 W/m⋅K thermal conductivity. In addition, 3D-printed modular walls exhibit ductile behavior and maintain structural integrity up to 600 °C. Furthermore, a supplementary assessment of the optimal mixture modified with recycled concrete waste (Run-23+) demonstrated the viability of waste-aggregate integration for improved circular-economy performance. Microstructural analyses via XRD and SEM confirmed the dense formation of calcium silicate hydrate (C–S–H) networks and active pozzolanic reactions. Consequently, the present study demonstrates an advanced composite that combines low density with structural capacity, establishing a novel load-bearing thermal insulation material (LB-TIM). Moreover, by integrating this optimized LB-TIM mixture with custom designed 3D printed formwork technology, this study provides a novel and scalable manufacturing approach for sustainable, thermal-insulated and load-bearing material and modular infill wall elements.
- 13 August 2026
- Published by Elsevier in Journal of Building Engineering
- Vol. 130
Use of recycled aggregates in pumice-based geopolymer concretes
- 13 August 2026
- Published by Elsevier in Journal of Building Engineering
- Vol. 130
Use of recycled aggregates in pumice-based geopolymer concretes
- 31 January 2026
- Published by Journal of Innovative Engineering and Natural Science in Journal of Innovative Engineering and Natural Science
- Vol. 6 (1) , 36-50
Analytical investigation of structural elements produced from sustainable waste tire-based geopolymer for infill wall applications
With the increasing global population, various industrial demands have emerged. In response to these needs, construction and shelter have become fundamental aspects of human life, leading to rapid growth in the construction sector. However, the accelerated depletion of natural resources commonly used in industry poses a significant challenge to sustainability. The use of conventional building materials results in excessive consumption of natural resources and generates waste that can lead to irreversible environmental problems. This situation necessitates the investigation of new and sustainable alternatives to minimize the environmental impact of human activities. As a natural consequence of expanding industries driven by technological advancement, the volume of industrial waste is growing rapidly. The wastes must be either stored, disposed of, or reused. Considering the environmental damage associated with storage and disposal, the most appropriate solution is reuse, which contributes to sustainability by transforming waste into secondary raw materials. In this study, a combination of waste tires, marble waste, and bottom ash was utilized alongside pumice, a natural and lightweight aggregate. To facilitate the geopolymerization process, sodium hydroxide was employed in the preparation of the alkaline activating solution. The resulting geopolymer-based construction material was then evaluated for its potential application in reinforced concrete structural system. Stress-strain relationship of the sustainable geopolymer mixture, primarily derived from waste tires, were experimentally determined. Furthermore, the analytical performance of masonry units manufactured from this mixture was evaluated in infill wall-frame systems.
- 31 January 2026
- Published by Journal of Innovative Engineering and Natural Science in Journal of Innovative Engineering and Natural Science
- Vol. 6 (1) , 36-50
Analytical investigation of structural elements produced from sustainable waste tire-based geopolymer for infill wall applications
With the increasing global population, various industrial demands have emerged. In response to these needs, construction and shelter have become fundamental aspects of human life, leading to rapid growth in the construction sector. However, the accelerated depletion of natural resources commonly used in industry poses a significant challenge to sustainability. The use of conventional building materials results in excessive consumption of natural resources and generates waste that can lead to irreversible environmental problems. This situation necessitates the investigation of new and sustainable alternatives to minimize the environmental impact of human activities. As a natural consequence of expanding industries driven by technological advancement, the volume of industrial waste is growing rapidly. The wastes must be either stored, disposed of, or reused. Considering the environmental damage associated with storage and disposal, the most appropriate solution is reuse, which contributes to sustainability by transforming waste into secondary raw materials. In this study, a combination of waste tires, marble waste, and bottom ash was utilized alongside pumice, a natural and lightweight aggregate. To facilitate the geopolymerization process, sodium hydroxide was employed in the preparation of the alkaline activating solution. The resulting geopolymer-based construction material was then evaluated for its potential application in reinforced concrete structural system. Stress-strain relationship of the sustainable geopolymer mixture, primarily derived from waste tires, were experimentally determined. Furthermore, the analytical performance of masonry units manufactured from this mixture was evaluated in infill wall-frame systems.
- Open Access
Electrical Curing of Metakaolin- and GBFS-Based Geopolymers: A Sustainable Technology Aligned with the European Green Deal
On-site curing of metakaolin (MK)- and granulated blast furnace slag (GBFS)-based geopolymer mortars remains a major bottleneck compared to thermal treatment for early strength development, and electrical curing is proposed here as a highly scalable and energy-efficient alternative technology. Geopolymer mortars with 0–100% MK/GBFS binder ratios were activated using sodium silicate (SS) and sodium hydroxide (SH) solutions of the following molarities: 6, 8, 10, 12, and 14 M. Steel fiber (SF), carbon fiber (CF), waste erosion wire (EW), and carbon black (CB) microfiller were incorporated to enhance the electro-conductive efficiency of the geopolymer matrix. Specimens were subjected to electrical curing under 10 V and 20 V AC and were compared with benchmarking under ambient conditions of 23 °C and thermal conditions of 70 °C. The findings established that the incorporation of fibers substantially boosted the level of conductivity and mechanical performance, with 28-day compressive strengths of up to 88.30 MPa (0.50% EW, 20 V) and flexural strengths of up to 22.24 MPa (0.50% CF, 7 days), exceeding the results of conventional curing in various instances. Microstructural studies based on well-bonded geopolymer gels with fibers indicated uniform geopolymerization through electrical curing without deleterious fiber–matrix interactions. A multi-criteria decision support approach (the HD method) based on 273 parameters established 0.50% CF, 0.75% SF, 0.75% EW, and 1.00% CB as the group-wise optima and chose 0.75% EW as the single-best performing combination. The findings confirm that electrical curing is a low-carbon, cost-effective, and field-adjustable curing technology with the potential to achieve target strength ratings, in line with the European Green Deal’s climate-neutral building material goals.
Open AccessElectrical Curing of Metakaolin- and GBFS-Based Geopolymers: A Sustainable Technology Aligned with the European Green Deal
On-site curing of metakaolin (MK)- and granulated blast furnace slag (GBFS)-based geopolymer mortars remains a major bottleneck compared to thermal treatment for early strength development, and electrical curing is proposed here as a highly scalable and energy-efficient alternative technology. Geopolymer mortars with 0–100% MK/GBFS binder ratios were activated using sodium silicate (SS) and sodium hydroxide (SH) solutions of the following molarities: 6, 8, 10, 12, and 14 M. Steel fiber (SF), carbon fiber (CF), waste erosion wire (EW), and carbon black (CB) microfiller were incorporated to enhance the electro-conductive efficiency of the geopolymer matrix. Specimens were subjected to electrical curing under 10 V and 20 V AC and were compared with benchmarking under ambient conditions of 23 °C and thermal conditions of 70 °C. The findings established that the incorporation of fibers substantially boosted the level of conductivity and mechanical performance, with 28-day compressive strengths of up to 88.30 MPa (0.50% EW, 20 V) and flexural strengths of up to 22.24 MPa (0.50% CF, 7 days), exceeding the results of conventional curing in various instances. Microstructural studies based on well-bonded geopolymer gels with fibers indicated uniform geopolymerization through electrical curing without deleterious fiber–matrix interactions. A multi-criteria decision support approach (the HD method) based on 273 parameters established 0.50% CF, 0.75% SF, 0.75% EW, and 1.00% CB as the group-wise optima and chose 0.75% EW as the single-best performing combination. The findings confirm that electrical curing is a low-carbon, cost-effective, and field-adjustable curing technology with the potential to achieve target strength ratings, in line with the European Green Deal’s climate-neutral building material goals.
- 18 July 2025
- Published by Springer Nature in Asian Journal of Civil Engineering
- Vol. 26 (11) , 4581-4594
Pi Distribution method for numerical fracture analysis of reinforced concretes (RC) based recycled aggregates
- 18 July 2025
- Published by Springer Nature in Asian Journal of Civil Engineering
- Vol. 26 (11) , 4581-4594
Pi Distribution method for numerical fracture analysis of reinforced concretes (RC) based recycled aggregates
- Open Access
- 31 December 2024
- Published by Yildiz Technical University - DIGITAL COMMONS JOURNALS in Journal of Sustainable Construction Materials and Technologies
- Vol. 9 (4) , 402-411
Clustering Analysis of Compressive Strength of Structural Recycled Aggregate Concrete
Clustering analysis primarily highlights the in homogeneity of data and can be utilized in structural engineering to demonstrate strength irregularity. It is well-known that strength irregularity between neighboring floors within a structure or among structural elements can lead to non-holistic behavior. Therefore, the clustering of compressive strength holds significant importance. Despite the relevance, only a few studies have addressed the clustering of compressive strength in recycled aggregate concrete (RAC) and proposed potential solutions for clustering issues. This paper aims to investigate the clustering of compressive strength in RAC and explore viable solutions. In this experimental study, four concrete groups were produced under standard conditions. The first group included natural aggregate concretes (NAC) designed with the Absolute Volume Method (AVM) as control concretes. The second group, comprised of RAC, was designed with the equivalent mortar volume method (EVM) as the control RAC. The third group consisted of RAC treated with silica fume (SF) and designed using AVM, while the fourth group included RAC designed with EVM. Statistical analyses were conducted on the 28-day compressive strength test results. The results indicated that the strength class of compressive strength clusters varied among the four groups. The clustering of test results was influenced by the type of concrete components used and the design method employed. Additionally, using silica fume and adopting the Absolute Volume Method reduced strength fluctuation and regulated the strength class of clusters by bringing them closer together. In contrast, the Equivalent Mortar Volume Method resulted in a greater dispersion of strength classes. The clustering effect of recycled aggregate (RA) was more pronounced than that of natural aggregate (NA). Given these findings, it is essential to implement measures when utilizing RAC in sustainable structures to address potential clustering issues.
- 31 December 2024
- Published by Yildiz Technical University - DIGITAL COMMONS JOURNALS in Journal of Sustainable Construction Materials and Technologies
- Vol. 9 (4) , 402-411
Open AccessClustering Analysis of Compressive Strength of Structural Recycled Aggregate Concrete
Clustering analysis primarily highlights the in homogeneity of data and can be utilized in structural engineering to demonstrate strength irregularity. It is well-known that strength irregularity between neighboring floors within a structure or among structural elements can lead to non-holistic behavior. Therefore, the clustering of compressive strength holds significant importance. Despite the relevance, only a few studies have addressed the clustering of compressive strength in recycled aggregate concrete (RAC) and proposed potential solutions for clustering issues. This paper aims to investigate the clustering of compressive strength in RAC and explore viable solutions. In this experimental study, four concrete groups were produced under standard conditions. The first group included natural aggregate concretes (NAC) designed with the Absolute Volume Method (AVM) as control concretes. The second group, comprised of RAC, was designed with the equivalent mortar volume method (EVM) as the control RAC. The third group consisted of RAC treated with silica fume (SF) and designed using AVM, while the fourth group included RAC designed with EVM. Statistical analyses were conducted on the 28-day compressive strength test results. The results indicated that the strength class of compressive strength clusters varied among the four groups. The clustering of test results was influenced by the type of concrete components used and the design method employed. Additionally, using silica fume and adopting the Absolute Volume Method reduced strength fluctuation and regulated the strength class of clusters by bringing them closer together. In contrast, the Equivalent Mortar Volume Method resulted in a greater dispersion of strength classes. The clustering effect of recycled aggregate (RA) was more pronounced than that of natural aggregate (NA). Given these findings, it is essential to implement measures when utilizing RAC in sustainable structures to address potential clustering issues.
- 9 December 2024
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 25 (1) , 1-23
Alternating current curing of conductive fly ash-slag geopolymer mortars: performance, characterization and optimization
- 9 December 2024
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 25 (1) , 1-23
Alternating current curing of conductive fly ash-slag geopolymer mortars: performance, characterization and optimization
- Open Access
- 26 March 2024
- Published by Yildiz Technical University - DIGITAL COMMONS JOURNALS in Journal of Sustainable Construction Materials and Technologies
- Vol. 9 (1) , 60-71
Rheology of Superabsorbent Polymer-Modified and Basalt Fiber-Reinforced Cement Paste with Silica Fume: Response Surface Methodology
A composite's rheology can be changed by adding superabsorbent polymer (SAP) and basalt fibers and using silica fume. This study aimed to investigate the effects of these components on the viscosity and shear stress parameters of the paste. The proportions of the components were varied, with SAP content ranging from 0.01% to 0.03%, basalt fiber from 0% to 0.50%, silica fume (micro silica) at 15%, and water content from 0.40 to 0.50. Response surface methodology was used to optimize the mixture proportions, and the rheological properties of the resulting pastes were characterized using a rheometer. Results showed that the addition of SAP and basalt fiber had a significant impact on the rheological properties of the paste, with increasing amounts of both resulting in increased viscosity and shear stress. Overall, this study highlights the potential of SAP and basalt fiber in advances of the rheology of cement paste and provides insight into the optimal proportions of these components for achieving desired rheological properties. The findings of this study could be useful in developing high-performance concrete with enhanced rheological properties, which could have a wide range of applications in the construction industry. In addition, 0.50% BF, 0.01% SAP, and 0.445 water-to-cement were found as optimum proportions regarding the rheology of the cement paste.
- 26 March 2024
- Published by Yildiz Technical University - DIGITAL COMMONS JOURNALS in Journal of Sustainable Construction Materials and Technologies
- Vol. 9 (1) , 60-71
Open AccessRheology of Superabsorbent Polymer-Modified and Basalt Fiber-Reinforced Cement Paste with Silica Fume: Response Surface Methodology
A composite's rheology can be changed by adding superabsorbent polymer (SAP) and basalt fibers and using silica fume. This study aimed to investigate the effects of these components on the viscosity and shear stress parameters of the paste. The proportions of the components were varied, with SAP content ranging from 0.01% to 0.03%, basalt fiber from 0% to 0.50%, silica fume (micro silica) at 15%, and water content from 0.40 to 0.50. Response surface methodology was used to optimize the mixture proportions, and the rheological properties of the resulting pastes were characterized using a rheometer. Results showed that the addition of SAP and basalt fiber had a significant impact on the rheological properties of the paste, with increasing amounts of both resulting in increased viscosity and shear stress. Overall, this study highlights the potential of SAP and basalt fiber in advances of the rheology of cement paste and provides insight into the optimal proportions of these components for achieving desired rheological properties. The findings of this study could be useful in developing high-performance concrete with enhanced rheological properties, which could have a wide range of applications in the construction industry. In addition, 0.50% BF, 0.01% SAP, and 0.445 water-to-cement were found as optimum proportions regarding the rheology of the cement paste.
- Open Access
- 25 June 2023
- Published by Kirsehir Ahi Evran University in Sürdürülebilir Mühendislik Uygulamaları ve Teknolojik Gelişmeler Dergisi
- Vol. 6 (1) , 45-50
Süper Emici Polimer Katkılı Harçların Isıl İşlem ile Hava Küründe Mekanik Özellikleri
Günümüzde süper emici polimerlerin kullanım alanları gittikçe yaygınlaşmaktadır. Bu polimerlerin beton karışımı içerisindeki davranışları ve betonun mekanik özellikleri üzerindeki etkisi araştırılmaktadır. Bununla birlikte, süper emici polimerlerin harç ve çimento pastası fazları üzerindeki etkileri de önemli bir araştırma konusudur. Bu makale kapsamında, süper emici polimer katkılı harçların farklı kür şartları altındaki mekanik davranışları deneysel olarak incelenmiştir. Deneylerde, 18 adet süper emici polimer katkılı ve 3 adet katkısız harç fazında 15x15x15 cm boyutlu küp numuneler üretilmiştir. Süper emici polimer katkılı harçlarda, polimer katkı oranı literatürden optimum %0,3 olarak belirlenmiştir. Deney numuneleri süper emici polimer katkılı, ısıl işlem uygulanmadan 3-5-10 gün hava küründe ve 1 gün ısıl işlem uygulaması ardından 2-4-9 gün hava kürü koşullarına göre sınıflandırılmıştır. Her bir deney numunesi için eksenel basınç dayanımı testi gerçekleştirilmiştir. Deneysel sonuçlardan, numunelerin gerilme-şekil değiştirme eğrileri elde edilmiştir. Bu eğrilerin karşılaştırılması neticesinde, süper emici polimer katkılı harçların mekanik performansında (eksenel basınç dayanımı, elastisite modülü ve enerji tüketme kapasitesi) en efektif ısıl işlem ve hava kürü kombinasyonu belirlenmiştir. Çalışmamız ile, süper emici polimer katkılı beton, bu betondan üretilmiş yapı taşıyıcı sistem elemanı (kolon, kiriş, perde, döşeme, vb.) davranışları ve süper emici polimer katkılı betonun teorik olarak modellenmesi bilimsel araştırmalarına katkı sunulması hedeflenmiştir.
- 25 June 2023
- Published by Kirsehir Ahi Evran University in Sürdürülebilir Mühendislik Uygulamaları ve Teknolojik Gelişmeler Dergisi
- Vol. 6 (1) , 45-50
Open AccessSüper Emici Polimer Katkılı Harçların Isıl İşlem ile Hava Küründe Mekanik Özellikleri
Günümüzde süper emici polimerlerin kullanım alanları gittikçe yaygınlaşmaktadır. Bu polimerlerin beton karışımı içerisindeki davranışları ve betonun mekanik özellikleri üzerindeki etkisi araştırılmaktadır. Bununla birlikte, süper emici polimerlerin harç ve çimento pastası fazları üzerindeki etkileri de önemli bir araştırma konusudur. Bu makale kapsamında, süper emici polimer katkılı harçların farklı kür şartları altındaki mekanik davranışları deneysel olarak incelenmiştir. Deneylerde, 18 adet süper emici polimer katkılı ve 3 adet katkısız harç fazında 15x15x15 cm boyutlu küp numuneler üretilmiştir. Süper emici polimer katkılı harçlarda, polimer katkı oranı literatürden optimum %0,3 olarak belirlenmiştir. Deney numuneleri süper emici polimer katkılı, ısıl işlem uygulanmadan 3-5-10 gün hava küründe ve 1 gün ısıl işlem uygulaması ardından 2-4-9 gün hava kürü koşullarına göre sınıflandırılmıştır. Her bir deney numunesi için eksenel basınç dayanımı testi gerçekleştirilmiştir. Deneysel sonuçlardan, numunelerin gerilme-şekil değiştirme eğrileri elde edilmiştir. Bu eğrilerin karşılaştırılması neticesinde, süper emici polimer katkılı harçların mekanik performansında (eksenel basınç dayanımı, elastisite modülü ve enerji tüketme kapasitesi) en efektif ısıl işlem ve hava kürü kombinasyonu belirlenmiştir. Çalışmamız ile, süper emici polimer katkılı beton, bu betondan üretilmiş yapı taşıyıcı sistem elemanı (kolon, kiriş, perde, döşeme, vb.) davranışları ve süper emici polimer katkılı betonun teorik olarak modellenmesi bilimsel araştırmalarına katkı sunulması hedeflenmiştir.