Martin Bliss
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Martin Bliss has a total of 85 co-authors. Here are the top co-authors by number of shared publications:
- Ralph Gottschalg
Fraunhofer CSP Halle (Saale) Germany
22 shared publications T.R. Betts
Centre for Renewable Energy Systems Technology (CREST), Department of Electronic and Electrical Engineering, Loughborough University, Loughborough, Leicestershire, LE11 3TU, UK
5 shared publications- Xiaofeng Wu
Centre for Renewable Energy Systems Technology (CREST), Wolfon School Mechanical, Electronic and Manufacturing Engineering, Loughborough University, Loughborough LE113TU, UK
5 shared publications - Archana Sinha
SLAC National Accelerator Laboratory, Menlo Park, CA, USA
4 shared publications - Jiang Zhu
Centre for Renewable Energy Systems Technology, Wolfson School of Mechanical, Electrical and Manufacturing Engineering, Loughborough University, Loughborough LE11 3TU, U.K.
4 shared publications Thomas R. Betts
Centre for Renewable Energy Systems Technology, Wolfson School Mechanical, Electronic and Manufacturing Engineering, Loughborough University, Loughborough, U.K.
4 shared publications
Latest Publications
- Open Access
- 22 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 12 (6) , 1296-1302
Impact of In-Situ Cd Saturation MOCVD Grown CdTe Solar Cells on As Doping and VOC
In-situ Cd-saturated growth of polycrystalline CdTe:As thin film was performed by metal organic chemical vapour deposition at a low temperature of 350 °C, to investigate the impact on As doping and device VOC. Device characterization showed conversion efficiency of ∼14%, and VOC of 772 mV, which is an improvement to the baseline device with CdTe:As absorber layer grown at 390 °C under non-saturated conditions. When the low temperature Cd-saturated growth was combined with chlorine heat treatment at a higher temperature of 440 °C (in contrast with the standard 420 °C) for 10 min, device efficiency improved to ∼17% with a high VOC of 877 mV. As a result, ∼100 mV boost in VOC from baseline is demonstrated with Cd-saturated CdTe:As device. Micro-photoluminescence and time-resolved photoluminescence measurements performed on these Cd-saturated CdTe:As devices confirmed that minority carrier lifetime significantly improved.
- 22 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 12 (6) , 1296-1302
Open AccessImpact of In-Situ Cd Saturation MOCVD Grown CdTe Solar Cells on As Doping and VOC
In-situ Cd-saturated growth of polycrystalline CdTe:As thin film was performed by metal organic chemical vapour deposition at a low temperature of 350 °C, to investigate the impact on As doping and device VOC. Device characterization showed conversion efficiency of ∼14%, and VOC of 772 mV, which is an improvement to the baseline device with CdTe:As absorber layer grown at 390 °C under non-saturated conditions. When the low temperature Cd-saturated growth was combined with chlorine heat treatment at a higher temperature of 440 °C (in contrast with the standard 420 °C) for 10 min, device efficiency improved to ∼17% with a high VOC of 877 mV. As a result, ∼100 mV boost in VOC from baseline is demonstrated with Cd-saturated CdTe:As device. Micro-photoluminescence and time-resolved photoluminescence measurements performed on these Cd-saturated CdTe:As devices confirmed that minority carrier lifetime significantly improved.
- Open Access
- 1 April 2019
- Published by Elsevier in Solar Energy
- Vol. 182, 256-263
Interlaboratory comparison of short-circuit current versus irradiance linearity measurements of photovoltaic devices
- 1 April 2019
- Published by Elsevier in Solar Energy
- Vol. 182, 256-263
Open AccessInterlaboratory comparison of short-circuit current versus irradiance linearity measurements of photovoltaic devices
- Open Access
- 7 March 2019
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 7 (12) , 7042-7052
Deposition and application of a Mo–N back contact diffusion barrier yielding a 12.0% efficiency solution-processed CIGS solar cell using an amine–thiol solvent system
The use of a Mo–N barrier for solution-processed CIGS results in reduced MoSe2 formation. This enabled longer selenization time, enhanced grain growth and performance.
- 7 March 2019
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 7 (12) , 7042-7052
Open AccessDeposition and application of a Mo–N back contact diffusion barrier yielding a 12.0% efficiency solution-processed CIGS solar cell using an amine–thiol solvent system
The use of a Mo–N barrier for solution-processed CIGS results in reduced MoSe2 formation. This enabled longer selenization time, enhanced grain growth and performance.
- Open Access
- 14 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 9 (1) , 220-226
Spectral Response Measurements of Perovskite Solar Cells
A new spectral response (SR) measurement routine is proposed that is universally applicable for all perovskite devices. It is aimed at improving measurement accuracy and repeatability of SR curves and current-voltage curve spectral mismatch factor (MMF) corrections. Frequency response, effects of preconditioning as well as dependency on incident light intensity and voltage load on SR measurements are characterized on two differently structured perovskite device types. It is shown that device preconditioning affects the SR shape, causing errors in spectral MMF corrections of up to 0.8% when using a reference cell with a good spectral match and a class A solar simulator. Wavelength dependent response to incident light intensity and voltage load is observed on both device types, which highlights the need to measure at short-circuit current and maximum power point to correct spectral mismatch. The method with recommendations given ensures that the correct measurement conditions are applied and measurements are corrected for instability in performance.
- 14 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 9 (1) , 220-226
Open AccessSpectral Response Measurements of Perovskite Solar Cells
A new spectral response (SR) measurement routine is proposed that is universally applicable for all perovskite devices. It is aimed at improving measurement accuracy and repeatability of SR curves and current-voltage curve spectral mismatch factor (MMF) corrections. Frequency response, effects of preconditioning as well as dependency on incident light intensity and voltage load on SR measurements are characterized on two differently structured perovskite device types. It is shown that device preconditioning affects the SR shape, causing errors in spectral MMF corrections of up to 0.8% when using a reference cell with a good spectral match and a class A solar simulator. Wavelength dependent response to incident light intensity and voltage load is observed on both device types, which highlights the need to measure at short-circuit current and maximum power point to correct spectral mismatch. The method with recommendations given ensures that the correct measurement conditions are applied and measurements are corrected for instability in performance.
- Open Access
- 17 October 2018
- Published by EDP Sciences in International Journal of Metrology and Quality Engineering
- Vol. 9, 8
Results of the round robin calibration of reference solar cells within the PhotoClass project
An intercomparison of terrestrial photovoltaic (PV) calibrations was performed among a number of European calibration and testing laboratories that participated in the European Metrology Research Program (EMRP) project “PhotoClass”. The purpose of this intercomparison was to evaluate the comparability of calibration and testing services within the stated uncertainties of the individual laboratories. The calibration objects were two world photovoltaic scale (WPVS)-type reference solar cells, one made from crystalline silicon and one made from GaAs. The calibration value (CV) was the short-circuit current under standard test conditions (ISTC). In conclusion, it was found that the CVs are all consistent within the stated uncertainties. This result strengthens the reliance in the calibration chain and in the PV calibration infrastructure in Europe.
- 17 October 2018
- Published by EDP Sciences in International Journal of Metrology and Quality Engineering
- Vol. 9, 8
Open AccessResults of the round robin calibration of reference solar cells within the PhotoClass project
An intercomparison of terrestrial photovoltaic (PV) calibrations was performed among a number of European calibration and testing laboratories that participated in the European Metrology Research Program (EMRP) project “PhotoClass”. The purpose of this intercomparison was to evaluate the comparability of calibration and testing services within the stated uncertainties of the individual laboratories. The calibration objects were two world photovoltaic scale (WPVS)-type reference solar cells, one made from crystalline silicon and one made from GaAs. The calibration value (CV) was the short-circuit current under standard test conditions (ISTC). In conclusion, it was found that the CVs are all consistent within the stated uncertainties. This result strengthens the reliance in the calibration chain and in the PV calibration infrastructure in Europe.
- Open Access
- 10 July 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 8 (5) , 1297-1304
Electroluminescence Imaging of PV Devices: Advanced Vignetting Calibration
Electroluminescence (EL) imaging is affected by off-axis illumination together with sensor and lens imperfections. The images’ spatial intensity distribution is mainly determined by the vignetting effect. For quantitative EL imaging, its correction is essential. If neglected, intensities can vary significantly (>50%) across the image. This paper introduces and tests four vignetting measurement methods. The quantitative comparison of different methods shows that vignetting should be characterized preferably in plane by the source of the same type as the photovoltaic (PV) device to be tested. A direct PV-based measurement in short distance with spatial inhomogeneity correction is proposed for general-purpose vignetting characterization. For precise vignetting characterization, vignetting-object separation using pattern recognition is proposed. The use of non-PV light sources for vignetting characterization can cause vignetting overcorrection and can even decrease the quality of the vignetting-corrected images.
- 10 July 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 8 (5) , 1297-1304
Open AccessElectroluminescence Imaging of PV Devices: Advanced Vignetting Calibration
Electroluminescence (EL) imaging is affected by off-axis illumination together with sensor and lens imperfections. The images’ spatial intensity distribution is mainly determined by the vignetting effect. For quantitative EL imaging, its correction is essential. If neglected, intensities can vary significantly (>50%) across the image. This paper introduces and tests four vignetting measurement methods. The quantitative comparison of different methods shows that vignetting should be characterized preferably in plane by the source of the same type as the photovoltaic (PV) device to be tested. A direct PV-based measurement in short distance with spatial inhomogeneity correction is proposed for general-purpose vignetting characterization. For precise vignetting characterization, vignetting-object separation using pattern recognition is proposed. The use of non-PV light sources for vignetting characterization can cause vignetting overcorrection and can even decrease the quality of the vignetting-corrected images.
- Open Access
- 19 January 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 7 (2) , 486-492
Compressed Sensing Current Mapping Spatial Characterization of Photovoltaic Devices
A new photovoltaic (PV) device current mapping method has been developed, combining the recently introduced compressed sensing (CS) sampling theory with light beam induced current (LBIC) measurements. Instead of a raster scan, compressive sampling is applied using a digital micromirror device. The aim is to significantly reduce the time required to produce a current map, compared to conventional LBIC measurements. This is achieved by acquiring fewer measurements than a full raster scan and by utilizing the fast response of the micromirror device to modulate measurement conditions. The method has been implemented on an optical current mapping setup built at the National Physical Laboratory, U.K. Measurements with two different PV cells are presented in this paper and an analytical description for realization of an optimized CS current mapping system is provided. The experimental results illustrate the feasibility of the method and its potential to significantly reduce measurement time of current mapping of PV devices.
- 19 January 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 7 (2) , 486-492
Open AccessCompressed Sensing Current Mapping Spatial Characterization of Photovoltaic Devices
A new photovoltaic (PV) device current mapping method has been developed, combining the recently introduced compressed sensing (CS) sampling theory with light beam induced current (LBIC) measurements. Instead of a raster scan, compressive sampling is applied using a digital micromirror device. The aim is to significantly reduce the time required to produce a current map, compared to conventional LBIC measurements. This is achieved by acquiring fewer measurements than a full raster scan and by utilizing the fast response of the micromirror device to modulate measurement conditions. The method has been implemented on an optical current mapping setup built at the National Physical Laboratory, U.K. Measurements with two different PV cells are presented in this paper and an analytical description for realization of an optimized CS current mapping system is provided. The experimental results illustrate the feasibility of the method and its potential to significantly reduce measurement time of current mapping of PV devices.
- Open Access
- 22 August 2016
- Published by MDPI AG in Journal of Imaging
- Vol. 2 (3) , 23
Cross-Characterization for Imaging Parasitic Resistive Losses in Thin-Film Photovoltaic Modules
Thin-film photovoltaic (PV) modules often suffer from a variety of parasitic resistive losses in transparent conductive oxide (TCO) and absorber layers that significantly affect the module electrical performance. This paper presents the holistic investigation of resistive effects due to TCO lateral sheet resistance and shunts in amorphous-silicon (a-Si) thin-film PV modules by simultaneous use of three different imaging techniques, electroluminescence (EL), lock-in thermography (LIT) and light beam induced current (LBIC), under different operating conditions. Results from individual techniques have been compared and analyzed for particular type of loss channel, and combination of these techniques has been used to obtain more detailed information for the identification and classification of these loss channels. EL and LIT techniques imaged the TCO lateral resistive effects with different spatial sensitivity across the cell width. For quantification purpose, a distributed diode modeling and simulation approach has been exploited to estimate TCO sheet resistance from EL intensity pattern and effect of cell width on module efficiency. For shunt investigation, LIT provided better localization of severe shunts, while EL and LBIC given good localization of weak shunts formed by the scratches. The impact of shunts on the photocurrent generation capability of individual cells has been assessed by li-LBIC technique. Results show that the cross-characterization by different imaging techniques provides additional information, which aids in identifying the nature and severity of loss channels with more certainty, along with their relative advantages and limitations in particular cases.
- 22 August 2016
- Published by MDPI AG in Journal of Imaging
- Vol. 2 (3) , 23
Open AccessCross-Characterization for Imaging Parasitic Resistive Losses in Thin-Film Photovoltaic Modules
Thin-film photovoltaic (PV) modules often suffer from a variety of parasitic resistive losses in transparent conductive oxide (TCO) and absorber layers that significantly affect the module electrical performance. This paper presents the holistic investigation of resistive effects due to TCO lateral sheet resistance and shunts in amorphous-silicon (a-Si) thin-film PV modules by simultaneous use of three different imaging techniques, electroluminescence (EL), lock-in thermography (LIT) and light beam induced current (LBIC), under different operating conditions. Results from individual techniques have been compared and analyzed for particular type of loss channel, and combination of these techniques has been used to obtain more detailed information for the identification and classification of these loss channels. EL and LIT techniques imaged the TCO lateral resistive effects with different spatial sensitivity across the cell width. For quantification purpose, a distributed diode modeling and simulation approach has been exploited to estimate TCO sheet resistance from EL intensity pattern and effect of cell width on module efficiency. For shunt investigation, LIT provided better localization of severe shunts, while EL and LBIC given good localization of weak shunts formed by the scratches. The impact of shunts on the photocurrent generation capability of individual cells has been assessed by li-LBIC technique. Results show that the cross-characterization by different imaging techniques provides additional information, which aids in identifying the nature and severity of loss channels with more certainty, along with their relative advantages and limitations in particular cases.
- Open Access
- 2 July 2015
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 54 (8S1) , 08KG03
Towards modelling realistic ageing rates of amorphous silicon devices in operational environment
This paper presents a method to de-convolute the annealing and degradation processes of amorphous silicon devices. This will allow modelling realistic outdoor operation. Six devices underwent 14000 h indoor light exposure at different and varying thermal conditions. The devices are exposed to light at variable temperatures between 25 and 85 ?C under illumination as well as annealed in the dark. The temperature set-points were altered several times during the test to gain insights on how the balance between light induced degradation and thermal annealing is shifted. Measurements show that the degradation level is largely determined by the device?s operating temperature and both processes balance themselves out without consideration of device history. This is explained by the proposed modelling approach based on the defect pool model. The key parameters in the proposed modelling approach are the effective activation energies for degradation and annealing.
- 2 July 2015
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 54 (8S1) , 08KG03
Open AccessTowards modelling realistic ageing rates of amorphous silicon devices in operational environment
This paper presents a method to de-convolute the annealing and degradation processes of amorphous silicon devices. This will allow modelling realistic outdoor operation. Six devices underwent 14000 h indoor light exposure at different and varying thermal conditions. The devices are exposed to light at variable temperatures between 25 and 85 ?C under illumination as well as annealed in the dark. The temperature set-points were altered several times during the test to gain insights on how the balance between light induced degradation and thermal annealing is shifted. Measurements show that the degradation level is largely determined by the device?s operating temperature and both processes balance themselves out without consideration of device history. This is explained by the proposed modelling approach based on the defect pool model. The key parameters in the proposed modelling approach are the effective activation energies for degradation and annealing.
- Open Access
- 1 July 2015
- Published by Institution of Engineering and Technology (IET) in IET Renewable Power Generation
- Vol. 9 (5) , 446-452
Spatially and spectrally resolved electroluminescence measurement system for photovoltaic characterisation
A system that combines the advantages of fast global electroluminescence (EL) imaging and detailed spectrally resolved EL measurements is presented. A charge‐coupled device camera‐based EL imaging system is used to measure the intensity of radiative recombination of the photovoltaic (PV) device spatially resolved over its full area. A monochromator‐based system is utilised to measure localised emission spectra at given points of interest. Measurements of multi‐crystalline and amorphous silicon PV devices demonstrate the potential to investigate radiative defects and reveal performance variations and non‐uniformities. This links inhomogeneities much closer to device physics than using camera‐based EL only.
- 1 July 2015
- Published by Institution of Engineering and Technology (IET) in IET Renewable Power Generation
- Vol. 9 (5) , 446-452
Open AccessSpatially and spectrally resolved electroluminescence measurement system for photovoltaic characterisation
A system that combines the advantages of fast global electroluminescence (EL) imaging and detailed spectrally resolved EL measurements is presented. A charge‐coupled device camera‐based EL imaging system is used to measure the intensity of radiative recombination of the photovoltaic (PV) device spatially resolved over its full area. A monochromator‐based system is utilised to measure localised emission spectra at given points of interest. Measurements of multi‐crystalline and amorphous silicon PV devices demonstrate the potential to investigate radiative defects and reveal performance variations and non‐uniformities. This links inhomogeneities much closer to device physics than using camera‐based EL only.