Tymon Barwicz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Tymon Barwicz has a total of 85 co-authors. Here are the top co-authors by number of shared publications:
Nicolas Boyer
IBM Bromont, Bromont, Canada
5 shared publications- Paul Fortier
IBM Bromont, Bromont, Canada
4 shared publications Shotaro Takenobu
AGC Inc., Yokohama, Japan
4 shared publicationsSwetha Kamlapurkar
4 shared publications- Alexander Janta-Polczynski
IBM Bromont, Bromont, QC, Canada
3 shared publications Bo Peng
GlobalFoundries, Hopewell Junction, NY, USA
3 shared publications
Latest Publications
- 1 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Self-Aligned Polymeric Fiber Interface with 20/mm Port Density and 1.1 dB O-Band Loss
We show a self-aligned compliant polymer interface between standard fiber connectors and nanophotonic waveguides with a polarization independent 1.1dB loss and a broadband response. The required chip interface is available through a commercial photonic foundry.
- 1 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Self-Aligned Polymeric Fiber Interface with 20/mm Port Density and 1.1 dB O-Band Loss
We show a self-aligned compliant polymer interface between standard fiber connectors and nanophotonic waveguides with a polarization independent 1.1dB loss and a broadband response. The required chip interface is available through a commercial photonic foundry.
- 6 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 26 (2) , 1-12
Advances in Interfacing Optical Fibers to Nanophotonic Waveguides Via Mechanically Compliant Polymer Waveguides
Interfacing standard optical fibers with high index-contrast photonic waveguides remains a substantial challenge restricting the cost-efficiency and scalability of silicon photonic devices. To address this, we have proposed a mechanically compliant polymer interface, formed of a standard fiber connection and a flexible ribbon with lithographically defined polymer waveguides. Self-aligned mechanical assembly and optical mode evolution designs are employed for low cost and large spectral bandwidth. In this paper, we review our progress leading to the full demonstration of this concept with -1.8 dB peak transmission from a plugged-in standard fiber connector to Si wire waveguides. This with 0.7 dB roll-off on a 100 nm bandwidth and all polarization. We present a comprehensive analysis of loss sources and discuss intermediate results, self-alignment accuracy, and reliability.
- 6 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 26 (2) , 1-12
Advances in Interfacing Optical Fibers to Nanophotonic Waveguides Via Mechanically Compliant Polymer Waveguides
Interfacing standard optical fibers with high index-contrast photonic waveguides remains a substantial challenge restricting the cost-efficiency and scalability of silicon photonic devices. To address this, we have proposed a mechanically compliant polymer interface, formed of a standard fiber connection and a flexible ribbon with lithographically defined polymer waveguides. Self-aligned mechanical assembly and optical mode evolution designs are employed for low cost and large spectral bandwidth. In this paper, we review our progress leading to the full demonstration of this concept with -1.8 dB peak transmission from a plugged-in standard fiber connector to Si wire waveguides. This with 0.7 dB roll-off on a 100 nm bandwidth and all polarization. We present a comprehensive analysis of loss sources and discuss intermediate results, self-alignment accuracy, and reliability.
- Top Cited Papers
- 1 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 25 (5) , 1-11
300-mm Monolithic Silicon Photonics Foundry Technology
A competitive 300-mm silicon photonics foundry technology has been developed by GLOBALFOUNDRIES for general availability, which takes advantage of advanced CMOS process technology and provides a manufacturing scale. A state-of-the-art process design kit offers a codesign environment with access to a comprehensive photonics device library along with a monolithically integrated SOI CMOS device library. Advances in automated wafer-level optical test enable statistical photonic device characterization for development, photonic modeling, and manufacturing controls. The key challenges and solutions in developing a manufacturable photonic technology with state-of-the-art performance are described, as well as a roadmap for next generation high-performance monolithic silicon photonics are outlined.
- 1 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 25 (5) , 1-11
Top Cited Papers300-mm Monolithic Silicon Photonics Foundry Technology
A competitive 300-mm silicon photonics foundry technology has been developed by GLOBALFOUNDRIES for general availability, which takes advantage of advanced CMOS process technology and provides a manufacturing scale. A state-of-the-art process design kit offers a codesign environment with access to a comprehensive photonics device library along with a monolithically integrated SOI CMOS device library. Advances in automated wafer-level optical test enable statistical photonic device characterization for development, photonic modeling, and manufacturing controls. The key challenges and solutions in developing a manufacturable photonic technology with state-of-the-art performance are described, as well as a roadmap for next generation high-performance monolithic silicon photonics are outlined.
- 1 January 2018
- Published by Optica Publishing Group
- p. STh4B.8
Automated Assembly of Duplex Fiber Connectors to Photonic Chips in Standard Microelectronic Tools
We demonstrate self-aligned assembly of LC-terminated fibers to chips in a manner compatible with standard microelectronics assembly lines. We show -1.5dB peak transmission to chip with 0.9dB penalty over a 100nm bandwidth and all polarization.
- 1 January 2018
- Published by Optica Publishing Group
- p. STh4B.8
Automated Assembly of Duplex Fiber Connectors to Photonic Chips in Standard Microelectronic Tools
We demonstrate self-aligned assembly of LC-terminated fibers to chips in a manner compatible with standard microelectronics assembly lines. We show -1.5dB peak transmission to chip with 0.9dB penalty over a 100nm bandwidth and all polarization.
- 1 January 2016
- Published by Optica Publishing Group
- p. FTu1D.2
A compliant polymer interface with 1.4dB loss between standard fibers and nanophotonic waveguides
We demonstrate improved performance in interfacing standard fibers with nanophotonic waveguides through a mechanically compliant polymer interface. We show −1.4dB peak transmission with 0.8dB penalty over the ~100nm bandwidth measured and all polarizations.
- 1 January 2016
- Published by Optica Publishing Group
- p. FTu1D.2
A compliant polymer interface with 1.4dB loss between standard fibers and nanophotonic waveguides
We demonstrate improved performance in interfacing standard fibers with nanophotonic waveguides through a mechanically compliant polymer interface. We show −1.4dB peak transmission with 0.8dB penalty over the ~100nm bandwidth measured and all polarizations.
- 1 January 2015
- Published by Optica Publishing Group
- p. Th3F.4
Flexible Polymer Optical Waveguide for Si Photonics Interface
We realize a technology of single mode polymer optical waveguide with precise alignment structures suitable for silicon photonic component assembly. The propagation loss is 0.5 dB/cm at 1550 nm.
- 1 January 2015
- Published by Optica Publishing Group
- p. Th3F.4
Flexible Polymer Optical Waveguide for Si Photonics Interface
We realize a technology of single mode polymer optical waveguide with precise alignment structures suitable for silicon photonic component assembly. The propagation loss is 0.5 dB/cm at 1550 nm.
- Open Access
- 18 December 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 21 (4) , 212-222
Demonstration of a High Extinction Ratio Monolithic CMOS Integrated Nanophotonic Transmitter and 16 Gb/s Optical Link
We present a 16-Gb/s transmitter composed of a stacked voltage-mode CMOS driver and periodic-loaded reverse biased pn junction Mach-Zehnder modulator. The transmitter shows 9-dB extinction ratio and 10.3-pJ/bit power consumption and operates with 1.3 μm light. Penalties as low as 0.5 dB were seen as compared to a 25-Gb/s LiNbO 3 transmitter with both a monolithic metal-semiconductor-metal receiver and a reference receiver at 16-Gb/s operation. We also present an analytic expression for relative transmitter penalty (RTP), which allows one to quickly assess the system impact of design parameters such as peak-to-peak modulator drive voltage, modulator figure of merit, and transmitter extinction ratio to determine the circumstances under which a stacked CMOS cascode driver is desirable.
- 18 December 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 21 (4) , 212-222
Open AccessDemonstration of a High Extinction Ratio Monolithic CMOS Integrated Nanophotonic Transmitter and 16 Gb/s Optical Link
We present a 16-Gb/s transmitter composed of a stacked voltage-mode CMOS driver and periodic-loaded reverse biased pn junction Mach-Zehnder modulator. The transmitter shows 9-dB extinction ratio and 10.3-pJ/bit power consumption and operates with 1.3 μm light. Penalties as low as 0.5 dB were seen as compared to a 25-Gb/s LiNbO 3 transmitter with both a monolithic metal-semiconductor-metal receiver and a reference receiver at 16-Gb/s operation. We also present an analytic expression for relative transmitter penalty (RTP), which allows one to quickly assess the system impact of design parameters such as peak-to-peak modulator drive voltage, modulator figure of merit, and transmitter extinction ratio to determine the circumstances under which a stacked CMOS cascode driver is desirable.
- Open Access
- 1 May 2014
- Published by Optica Publishing Group in Optics Express
- Vol. 22 (9) , 11167-11174
Polarization rotator-splitters and controllers in a Si_3N_4-on-SOI integrated photonics platform
We demonstrate novel polarization management devices in a custom-designed silicon nitride (Si3N4) on silicon-on-insulator (SOI) integrated photonics platform. In the platform, Si3N4 waveguides are defined atop silicon waveguides. A broadband polarization rotator-splitter using a TM0-TE1 mode converter in a composite Si3N4-silicon waveguide is demonstrated. The polarization crosstalk, insertion loss, and polarization dependent loss are less than −19 dB, 1.5 dB, and 1.0 dB, respectively, over a bandwidth of 80 nm. A polarization controller composed of polarization rotator-splitters, multimode interference couplers, and thin film heaters is also demonstrated.
- 1 May 2014
- Published by Optica Publishing Group in Optics Express
- Vol. 22 (9) , 11167-11174
Open AccessPolarization rotator-splitters and controllers in a Si_3N_4-on-SOI integrated photonics platform
We demonstrate novel polarization management devices in a custom-designed silicon nitride (Si3N4) on silicon-on-insulator (SOI) integrated photonics platform. In the platform, Si3N4 waveguides are defined atop silicon waveguides. A broadband polarization rotator-splitter using a TM0-TE1 mode converter in a composite Si3N4-silicon waveguide is demonstrated. The polarization crosstalk, insertion loss, and polarization dependent loss are less than −19 dB, 1.5 dB, and 1.0 dB, respectively, over a bandwidth of 80 nm. A polarization controller composed of polarization rotator-splitters, multimode interference couplers, and thin film heaters is also demonstrated.
- 1 May 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 05695503,p. 179-185
Assembly of mechanically compliant interfaces between optical fibers and nanophotonic chips
Silicon nanophotonics may bring disruptive advances to datacom, telecom, and high performance computing. However, the deployment of this technology is hampered by the difficulty of cost efficient optical inputs and outputs. To address this challenge, we have recently proposed a low-cost, mechanically compliant polymer interface between standard single mode fibers and nanophotonic waveguides. Our concept promises better mechanical reliability and better optical performance than existing technology. To manage the cost of assembly, we show here that self-alignment features can be effectively used to bridge the gap between the accuracy required by single-mode optics (1-2 um) and the capability of high-throughput microelectronic assembly equipment (~10 um). We describe the complaint interface, the assembly strategy, and the design of our re-alignment features. We demonstrate experimentally that misalignments at assembly as large as +/-10 um are re-aligned by our self-alignment structures to +/-1 to 2 um. Our approach enables existing microelectronics equipment to be used for singlemode optics assembly.
- 1 May 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 05695503,p. 179-185
Assembly of mechanically compliant interfaces between optical fibers and nanophotonic chips
Silicon nanophotonics may bring disruptive advances to datacom, telecom, and high performance computing. However, the deployment of this technology is hampered by the difficulty of cost efficient optical inputs and outputs. To address this challenge, we have recently proposed a low-cost, mechanically compliant polymer interface between standard single mode fibers and nanophotonic waveguides. Our concept promises better mechanical reliability and better optical performance than existing technology. To manage the cost of assembly, we show here that self-alignment features can be effectively used to bridge the gap between the accuracy required by single-mode optics (1-2 um) and the capability of high-throughput microelectronic assembly equipment (~10 um). We describe the complaint interface, the assembly strategy, and the design of our re-alignment features. We demonstrate experimentally that misalignments at assembly as large as +/-10 um are re-aligned by our self-alignment structures to +/-1 to 2 um. Our approach enables existing microelectronics equipment to be used for singlemode optics assembly.