Jonathan Govaerts
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jonathan Govaerts has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Ivan Gordon
Imo-imomec, Hasselt University, Hasselt, Belgium
2 shared publications - Jef Poortmans
IMEC, Leuven, Belgium
2 shared publications - Valérie Depauw
IMEC, Kapeldreef 75, B-3001 Leuven, Belgium
2 shared publications - Aart Willem Van Vuure
Department of Materials Engineering, KU Leuven, 3001 Leuven, Belgium
1 shared publication - Arvid van der Heide
IMO‐IMOMEC/Energyville IMEC Genk Belgium
1 shared publication B J Pawlak
IMEC
1 shared publication
Latest Publications
- 11 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Advanced Encapsulants for Reduced Thermal Mechanical Stress in Photovoltaic Modules: A Quantitative Analysis Using FBGS
In this work, two mini-modules using a 3D multi-ribbon interconnection are fabricated. One with TPO and the other with glass fiber reinforced TPO (GF TPO) encapsulant. Using fiber Braggs grating sensors (FBGS) attached to the cell, in situ temperature and strain are quantified during reliability tests in the form of thermal cycling from -40°C to +85°C. It was found that the temperature of the cell surface reaches -36°C and +81°C at its minimum and maximum respectively. The measured cell strain followed the same cycling behavior between tension and compression. The strain in the GF TPO based module was found to have a lower peak-to-peak (difference between max tension and compression) value. Also, a consistent difference between strain in parallel and perpendicular directions relative to the busbars was observed, with the latter one being larger.
- 11 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Advanced Encapsulants for Reduced Thermal Mechanical Stress in Photovoltaic Modules: A Quantitative Analysis Using FBGS
In this work, two mini-modules using a 3D multi-ribbon interconnection are fabricated. One with TPO and the other with glass fiber reinforced TPO (GF TPO) encapsulant. Using fiber Braggs grating sensors (FBGS) attached to the cell, in situ temperature and strain are quantified during reliability tests in the form of thermal cycling from -40°C to +85°C. It was found that the temperature of the cell surface reaches -36°C and +81°C at its minimum and maximum respectively. The measured cell strain followed the same cycling behavior between tension and compression. The strain in the GF TPO based module was found to have a lower peak-to-peak (difference between max tension and compression) value. Also, a consistent difference between strain in parallel and perpendicular directions relative to the busbars was observed, with the latter one being larger.
- 28 February 2022
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 30 (8) , 899-909
Large area co‐plated bifacial n‐PERT cells with polysilicon passivating contacts on both sides
- 28 February 2022
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 30 (8) , 899-909
Large area co‐plated bifacial n‐PERT cells with polysilicon passivating contacts on both sides
- 1 May 2014
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 124, 48-54
Plasma–silicone interaction during a-Si:H deposition on solar cell wafers bonded to glass
- 1 May 2014
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 124, 48-54
Plasma–silicone interaction during a-Si:H deposition on solar cell wafers bonded to glass
- 2 April 2013
- Published by Wiley in Physica Status Solidi (a)
- Vol. 210 (4) , 682-686
Layer transfer process assisted by laser scribing for thin film solar cells based on epitaxial foils
- 2 April 2013
- Published by Wiley in Physica Status Solidi (a)
- Vol. 210 (4) , 682-686
Layer transfer process assisted by laser scribing for thin film solar cells based on epitaxial foils
- 19 August 2010
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7773, 77730X
Performance of a new type of module based on back-contact solar cells
Imec has developed a new technology to integrate and interconnect back-contact solar cells into modules, based on embedding cells in silicone on top of a glass substrate. This technology aims at an improved optical performance and reliability (through the use of silicones and low-temperature metallization). One of the additional advantages is that the technology is suitable for integrating very thin cells into modules: whereas standalone interconnection of such fragile thin cells, e.g. tabbing and stringing, would significantly lower the throughput yield due to breakage, the cells are better protected if they are embedded inside silicone. The paper will first elaborate on the process flow, the background and motivation, advantages, drawbacks and limitations, and technical aspects of the developed technology. Then it will present the results of the measurements on the performance of functional solar cells processed into modules using this technology, discussing losses and loss mechanisms. Then, the approach towards determining the reliability of the module will be presented, indicating how imec aims at building up an ageing model, and elaborating the results on the failure mode and effect analysis, modeling, characterization and reliability testing.
- 19 August 2010
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7773, 77730X
Performance of a new type of module based on back-contact solar cells
Imec has developed a new technology to integrate and interconnect back-contact solar cells into modules, based on embedding cells in silicone on top of a glass substrate. This technology aims at an improved optical performance and reliability (through the use of silicones and low-temperature metallization). One of the additional advantages is that the technology is suitable for integrating very thin cells into modules: whereas standalone interconnection of such fragile thin cells, e.g. tabbing and stringing, would significantly lower the throughput yield due to breakage, the cells are better protected if they are embedded inside silicone. The paper will first elaborate on the process flow, the background and motivation, advantages, drawbacks and limitations, and technical aspects of the developed technology. Then it will present the results of the measurements on the performance of functional solar cells processed into modules using this technology, discussing losses and loss mechanisms. Then, the approach towards determining the reliability of the module will be presented, indicating how imec aims at building up an ageing model, and elaborating the results on the failure mode and effect analysis, modeling, characterization and reliability testing.