Mingming Qiu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mingming Qiu has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
Kang Huang
School of Mechanical Engineering, HeFei University of Technology, China
6 shared publicationsBingzhan Zhang
Hefei University of Technology, Hefei, Anhui, PR China
3 shared publicationsHan Zhao
3 shared publicationsLei Wang
3 shared publications- Han Zhao
School of Mechanical Engineering, Hefei University of Technology, Hefei, China
2 shared publications - Hao Sun
Hefei University of Technology
2 shared publications
Latest Publications
- 13 October 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
A dual-flank asymmetric microgeometry modification method for coaxial gear reducers
The noise problem of coaxial gear reducers in new energy vehicles (NEVs) is worsening due to increased rotational speeds and distinct load characteristics under driving and regenerative braking conditions. This paper proposes a dual-flank asymmetric microgeometry modification (MGM) methodology for coaxial gear reducers under bidirectional torque conditions. The proposed method is developed based on a system-level rigid-flexible coupling multi-body dynamic model, in which reverse-torque-induced planet-carrier deformation, loaded meshing misalignment, and tooth-surface load redistribution are used as the physical basis for flank-specific MGM optimization. Condition-specific objectives and independent parameter sets are assigned to the drive and coast flanks, thereby integrating NVH-oriented drive-flank optimization and contact-reliability-oriented coast-flank compensation within a unified asymmetric modification framework. For the drive flank, peak-to-peak transmission error is prioritized to suppress gear whine at the excitation source. For the coast flank, load distribution and contact stress are prioritized by minimizing the face load factor and balancing the edge load ratio, thereby compensating for system deflection. A genetic algorithm is then used to optimize the modification parameters. Simulations show that under driving conditions, the peak-to-peak transmission error and system vibration response are significantly reduced after optimization. Under regenerative braking, the asymmetric modification compensates for meshing misalignment, eliminates unilateral load concentration and edge contact risks, and improves the contact stress distribution. This strategy provides a novel foundation for enhancing full-condition NVH performance and reliability of EV transmission systems.
- 13 October 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
A dual-flank asymmetric microgeometry modification method for coaxial gear reducers
The noise problem of coaxial gear reducers in new energy vehicles (NEVs) is worsening due to increased rotational speeds and distinct load characteristics under driving and regenerative braking conditions. This paper proposes a dual-flank asymmetric microgeometry modification (MGM) methodology for coaxial gear reducers under bidirectional torque conditions. The proposed method is developed based on a system-level rigid-flexible coupling multi-body dynamic model, in which reverse-torque-induced planet-carrier deformation, loaded meshing misalignment, and tooth-surface load redistribution are used as the physical basis for flank-specific MGM optimization. Condition-specific objectives and independent parameter sets are assigned to the drive and coast flanks, thereby integrating NVH-oriented drive-flank optimization and contact-reliability-oriented coast-flank compensation within a unified asymmetric modification framework. For the drive flank, peak-to-peak transmission error is prioritized to suppress gear whine at the excitation source. For the coast flank, load distribution and contact stress are prioritized by minimizing the face load factor and balancing the edge load ratio, thereby compensating for system deflection. A genetic algorithm is then used to optimize the modification parameters. Simulations show that under driving conditions, the peak-to-peak transmission error and system vibration response are significantly reduced after optimization. Under regenerative braking, the asymmetric modification compensates for meshing misalignment, eliminates unilateral load concentration and edge contact risks, and improves the contact stress distribution. This strategy provides a novel foundation for enhancing full-condition NVH performance and reliability of EV transmission systems.
- Open Access
- 8 June 2026
- Published by Kaunas University of Technology (KTU) in Mechanics
- Vol. 32 (2) , 116-131
Research on Optimization Method of Vehicle Speed in Urban Road Conditions Based on Interval Analysis
Energy saving is the theme of automobile development, and intelligence and networking are the inevitable trend of automobile technology development. Aiming at the influence of traffic information on vehicle energy consumption, an economic speed planning method for intelligent connected vehicles based on interval analysis is proposed. Firstly, based on cellular automata and confidence interval theory, traffic information rules are introduced, and a road speed interval extraction method considering traffic density and traffic signal phase information is established. Secondly, according to the vehicle driving energy consumption model, the objective function of economic speed planning is established, and the traffic speed interval under different driving conditions is taken as the dynamic constraint condition, and the optimal control problem model of vehicle economic speed planning under urban road conditions is established; Then, the optimal control problem of vehicle economic speed is transformed into a model predictive control problem, and the DP algorithm is used to solve the optimal control sequence in each predictive domain, and the optimal speed sequence is planned by cyclic rolling optimization. Finally, through simulation and experimental verification, the results show that the method proposed in this paper can not only achieve all-green traffic at signal intersections, but also achieve good energy-saving effect, and the planning algorithm has fast calculation speed.
- 8 June 2026
- Published by Kaunas University of Technology (KTU) in Mechanics
- Vol. 32 (2) , 116-131
Open AccessResearch on Optimization Method of Vehicle Speed in Urban Road Conditions Based on Interval Analysis
Energy saving is the theme of automobile development, and intelligence and networking are the inevitable trend of automobile technology development. Aiming at the influence of traffic information on vehicle energy consumption, an economic speed planning method for intelligent connected vehicles based on interval analysis is proposed. Firstly, based on cellular automata and confidence interval theory, traffic information rules are introduced, and a road speed interval extraction method considering traffic density and traffic signal phase information is established. Secondly, according to the vehicle driving energy consumption model, the objective function of economic speed planning is established, and the traffic speed interval under different driving conditions is taken as the dynamic constraint condition, and the optimal control problem model of vehicle economic speed planning under urban road conditions is established; Then, the optimal control problem of vehicle economic speed is transformed into a model predictive control problem, and the DP algorithm is used to solve the optimal control sequence in each predictive domain, and the optimal speed sequence is planned by cyclic rolling optimization. Finally, through simulation and experimental verification, the results show that the method proposed in this paper can not only achieve all-green traffic at signal intersections, but also achieve good energy-saving effect, and the planning algorithm has fast calculation speed.
- 23 March 2026
- Published by SAGE Publications in Journal of Vibration and Control
Integrated steering and braking control for vehicle trajectory tracking under extreme conditions considering road adhesion coefficient—A dynamic weight coefficient allocation strategy
Under extreme operating conditions, coordinated steering and braking control is critical for vehicle safety. However, variations in road adhesion coefficients lead to differences in tire force utilization limits, necessitating dynamic adjustment of steering and braking control weights. To address this challenge, this study proposed a trajectory tracking control method with adhesion-aware dynamic weight allocation for steering and braking. Firstly, a lateral-longitudinal coupled vehicle dynamics model is developed, integrating front wheel steering angle and braking deceleration as control inputs. Secondly, a unified MPC framework is designed for trajectory tracking, where fuzzy logic dynamically adjusts the weighting coefficients between control effort and tracking error in the cost function based on real-time vehicle speed and reference trajectory curvature. Furthermore, to account for the influence of road adhesion coefficients on tire force utilization efficiency and driving stability, the mathematical model of weight coefficient correction is established. This two-stage adaptation mechanism integrates fuzzy logic and empirical rules based on mathematical models, enhances steering and braking maneuverability and trajectory tracking accuracy while rigorously guaranteeing stability across the adhesion-variant operating envelope. Simulation results demonstrate that the proposed controller achieves adaptive redistribution of steering and braking authority across different road surfaces, significantly improving handling stability and trajectory tracking precision compared to fixed-weight benchmarks. This method enhances the safety envelope of autonomous vehicles in adhesion-constrained emergency scenarios.
- 23 March 2026
- Published by SAGE Publications in Journal of Vibration and Control
Integrated steering and braking control for vehicle trajectory tracking under extreme conditions considering road adhesion coefficient—A dynamic weight coefficient allocation strategy
Under extreme operating conditions, coordinated steering and braking control is critical for vehicle safety. However, variations in road adhesion coefficients lead to differences in tire force utilization limits, necessitating dynamic adjustment of steering and braking control weights. To address this challenge, this study proposed a trajectory tracking control method with adhesion-aware dynamic weight allocation for steering and braking. Firstly, a lateral-longitudinal coupled vehicle dynamics model is developed, integrating front wheel steering angle and braking deceleration as control inputs. Secondly, a unified MPC framework is designed for trajectory tracking, where fuzzy logic dynamically adjusts the weighting coefficients between control effort and tracking error in the cost function based on real-time vehicle speed and reference trajectory curvature. Furthermore, to account for the influence of road adhesion coefficients on tire force utilization efficiency and driving stability, the mathematical model of weight coefficient correction is established. This two-stage adaptation mechanism integrates fuzzy logic and empirical rules based on mathematical models, enhances steering and braking maneuverability and trajectory tracking accuracy while rigorously guaranteeing stability across the adhesion-variant operating envelope. Simulation results demonstrate that the proposed controller achieves adaptive redistribution of steering and braking authority across different road surfaces, significantly improving handling stability and trajectory tracking precision compared to fixed-weight benchmarks. This method enhances the safety envelope of autonomous vehicles in adhesion-constrained emergency scenarios.
- 17 February 2026
- Published by SAGE Publications in Journal of Vibration and Control
Adaptive robust control of powertrain active mount system considering uncertainty
The Powertrain Active Mount System (PAMS) is the core component that damps the automotive powertrain, directly affecting the driving comfort of the vehicle. The active mount system adjusts the stiffness and damping of the mount system by controlling the electromagnetic output force of the actuator, making it a typical underactuated system. This underactuated system is prone to interference and is sensitive to parameters, which is particularly prominent in the current development of powertrains, which poses high requirements for control. Therefore, this paper proposes an adaptive robust control method. First, a model of an underactuated system is established, we express it in the form of the Udwadia-Kalaba (U-K) equation and provide the control objective, which is to make the acceleration of the vehicle frame equal to 0. And based on this, a nominal controller p 1 for the underactuated system is designed. The uncertainty is decomposed into matched and mismatched components, and on this basis, p 2 is designed to address the uncertainty of the initial state of the active mount control. For the issues of parameter uncertainty and external interference, p 3 is designed and an adaptive law is introduced to achieve adaptive adjustment of the control parameters. Finally, simulation analysis is conducted for different control methods. The results show that the proposed control method exhibits significant robustness in handling road surface disturbances, initial condition uncertainties, and mass parameter uncertainties. It effectively improves the vibration reduction effect and dynamic response accuracy of the PAMS and verifying the effectiveness of the controller.
- 17 February 2026
- Published by SAGE Publications in Journal of Vibration and Control
Adaptive robust control of powertrain active mount system considering uncertainty
The Powertrain Active Mount System (PAMS) is the core component that damps the automotive powertrain, directly affecting the driving comfort of the vehicle. The active mount system adjusts the stiffness and damping of the mount system by controlling the electromagnetic output force of the actuator, making it a typical underactuated system. This underactuated system is prone to interference and is sensitive to parameters, which is particularly prominent in the current development of powertrains, which poses high requirements for control. Therefore, this paper proposes an adaptive robust control method. First, a model of an underactuated system is established, we express it in the form of the Udwadia-Kalaba (U-K) equation and provide the control objective, which is to make the acceleration of the vehicle frame equal to 0. And based on this, a nominal controller p 1 for the underactuated system is designed. The uncertainty is decomposed into matched and mismatched components, and on this basis, p 2 is designed to address the uncertainty of the initial state of the active mount control. For the issues of parameter uncertainty and external interference, p 3 is designed and an adaptive law is introduced to achieve adaptive adjustment of the control parameters. Finally, simulation analysis is conducted for different control methods. The results show that the proposed control method exhibits significant robustness in handling road surface disturbances, initial condition uncertainties, and mass parameter uncertainties. It effectively improves the vibration reduction effect and dynamic response accuracy of the PAMS and verifying the effectiveness of the controller.
- 25 November 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 239 (13) , 6302-6316
Adaptive robust sliding mode control for AEB considering road adhesion condition constraint
Road adhesion condition is one of the key factors affecting the control effect of active emergency braking system (AEB), and emergency braking decision and slip rate tracking control are restricted by road adhesion condition. In this paper, an improved automatic emergency braking control method is proposed, which takes into account the constraints of road adhesion conditions. Firstly, a method of road adhesion coefficient recognition is established, which combines the database of road friction parameters with visual recognition algorithm to obtain the road adhesion coefficient. Secondly, a dynamic emergency braking distance model is established, which takes into account the road adhesion conditions and the motion state of vehicles and targets, so as to dynamically adjust the emergency braking decision distance. Then, considering the constraint of road adhesion coefficient on braking torque, a slip rate adaptive robust sliding mode controller with dynamic input constraint is designed. The input saturation boundary of the controller can be dynamically adjusted with different road adhesion conditions, and the dynamic compensation control for input saturation of the system is realized. Finally, the simulation experiments are carried out under different emergency braking conditions. The results show that the proposed method is deemed more consistent with the practicalities and demonstrates excellent braking performance and robustness.
- 25 November 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 239 (13) , 6302-6316
Adaptive robust sliding mode control for AEB considering road adhesion condition constraint
Road adhesion condition is one of the key factors affecting the control effect of active emergency braking system (AEB), and emergency braking decision and slip rate tracking control are restricted by road adhesion condition. In this paper, an improved automatic emergency braking control method is proposed, which takes into account the constraints of road adhesion conditions. Firstly, a method of road adhesion coefficient recognition is established, which combines the database of road friction parameters with visual recognition algorithm to obtain the road adhesion coefficient. Secondly, a dynamic emergency braking distance model is established, which takes into account the road adhesion conditions and the motion state of vehicles and targets, so as to dynamically adjust the emergency braking decision distance. Then, considering the constraint of road adhesion coefficient on braking torque, a slip rate adaptive robust sliding mode controller with dynamic input constraint is designed. The input saturation boundary of the controller can be dynamically adjusted with different road adhesion conditions, and the dynamic compensation control for input saturation of the system is realized. Finally, the simulation experiments are carried out under different emergency braking conditions. The results show that the proposed method is deemed more consistent with the practicalities and demonstrates excellent braking performance and robustness.
- 15 February 2024
- Published by Springer Nature in International Journal of Automotive Technology
- Vol. 25 (2) , 305-319
An Economical Velocity Planning Algorithm for Intelligent Connected Electric Vehicles Based on Real-Time Traffic Information
- 15 February 2024
- Published by Springer Nature in International Journal of Automotive Technology
- Vol. 25 (2) , 305-319
An Economical Velocity Planning Algorithm for Intelligent Connected Electric Vehicles Based on Real-Time Traffic Information
- 6 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 72 (6) , 7195-7210
A Regenerative Braking Control Strategy for ICVs Considering the Coupling Effect of Driving Conditions and Driving Styles
Regenerative braking is an important part of automotive energy-saving technology. Under different driving conditions and driving styles, the rules of the driver stepping on the accelerator pedal are different, which makes the regenerative braking intensity vary greatly. Different intensity of energy recovery is carried out under different driving conditions and driving styles, which is conducive to improving the efficiency of energy recovery. Therefore, we propose a regenerative braking control strategy (RBCS) based on an accelerator pedal for intelligent connected vehicles (ICVs) considering the coupling effect of driving conditions and driving styles. Firstly, a modified method of driving style characteristic parameters considering the influence of driving conditions is proposed. Secondly, α、β and γ are defined as accelerator pedal travel, driving condition and driving style correction coefficient respectively. The regenerative braking control strategy based on an accelerator pedal is established, which corrects the regenerative braking intensity according to correction coefficients. Thirdly, the driving data are obtained through the driver-in-the-loop experiment. On this basis, the characteristic parameters of driving style are modified, and the values of α、β and γ are determined. Finally, the vehicle simulation model and hardware-in-the-loop experiment platform are established to verify the RBCS. The results show that the economy of the vehicle is further improved.
- 6 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 72 (6) , 7195-7210
A Regenerative Braking Control Strategy for ICVs Considering the Coupling Effect of Driving Conditions and Driving Styles
Regenerative braking is an important part of automotive energy-saving technology. Under different driving conditions and driving styles, the rules of the driver stepping on the accelerator pedal are different, which makes the regenerative braking intensity vary greatly. Different intensity of energy recovery is carried out under different driving conditions and driving styles, which is conducive to improving the efficiency of energy recovery. Therefore, we propose a regenerative braking control strategy (RBCS) based on an accelerator pedal for intelligent connected vehicles (ICVs) considering the coupling effect of driving conditions and driving styles. Firstly, a modified method of driving style characteristic parameters considering the influence of driving conditions is proposed. Secondly, α、β and γ are defined as accelerator pedal travel, driving condition and driving style correction coefficient respectively. The regenerative braking control strategy based on an accelerator pedal is established, which corrects the regenerative braking intensity according to correction coefficients. Thirdly, the driving data are obtained through the driver-in-the-loop experiment. On this basis, the characteristic parameters of driving style are modified, and the values of α、β and γ are determined. Finally, the vehicle simulation model and hardware-in-the-loop experiment platform are established to verify the RBCS. The results show that the economy of the vehicle is further improved.
- 1 July 2021
- Published by SAGE Publications in Journal of Vibration and Control
- Vol. 28 (21-22) , 3269-3285
Research on intelligent vehicle lane changing and obstacle avoidance control based on road adhesion coefficient
Aimed at the safety and stability problems of intelligent vehicles under extreme conditions such as low adhesion road surface and emergency lane change and obstacle avoidance, this article designs a lane change and obstacle avoidance controller based on road adhesion coefficient. Using the nonlinear vehicle dynamics model as the prediction model, using the recursive least squares method to identify the road adhesion coefficient, considering the road adhesion coefficient to plan and adjust in the obstacle avoidance path as well as limit constraint conditions of the model predictive control controller, using model predictive control method for the expectation of intelligent vehicle trajectory tracking, travels tremendously guarantee the security and stability of driving. The joint CarSim–Simulink simulations results show that under poor road conditions, the trajectory tracking accuracy after optimization is higher and the vehicle is less prone to sideslip and instability. The lane change controller designed in this article has strong adaptability to different road surface adhesion coefficient, and all parameters can be controlled within a reasonable safety range at different speeds, with good robustness.
- 1 July 2021
- Published by SAGE Publications in Journal of Vibration and Control
- Vol. 28 (21-22) , 3269-3285
Research on intelligent vehicle lane changing and obstacle avoidance control based on road adhesion coefficient
Aimed at the safety and stability problems of intelligent vehicles under extreme conditions such as low adhesion road surface and emergency lane change and obstacle avoidance, this article designs a lane change and obstacle avoidance controller based on road adhesion coefficient. Using the nonlinear vehicle dynamics model as the prediction model, using the recursive least squares method to identify the road adhesion coefficient, considering the road adhesion coefficient to plan and adjust in the obstacle avoidance path as well as limit constraint conditions of the model predictive control controller, using model predictive control method for the expectation of intelligent vehicle trajectory tracking, travels tremendously guarantee the security and stability of driving. The joint CarSim–Simulink simulations results show that under poor road conditions, the trajectory tracking accuracy after optimization is higher and the vehicle is less prone to sideslip and instability. The lane change controller designed in this article has strong adaptability to different road surface adhesion coefficient, and all parameters can be controlled within a reasonable safety range at different speeds, with good robustness.
- 1 August 2020
- Published by Springer Nature in International Journal of Automotive Technology
- Vol. 21 (4) , 943-952
Model-Based Control of Synchronizer Shifting Process for Trajectory Tracking Control
- 1 August 2020
- Published by Springer Nature in International Journal of Automotive Technology
- Vol. 21 (4) , 943-952
Model-Based Control of Synchronizer Shifting Process for Trajectory Tracking Control