Andrea De Lieto Vollaro

Lighting very long road tunnels implies a high consumption of electrical energy since it requires a proper illumination during the whole day. In particular, in the daytime, the illuminance levels right at the tunnel entrance threshold and exit zones must be higher than those characterizing the inside of the tunnel; in this way, the eye of the driver is able to adapt and be safe while passing from a high natural illumination of the outside to the lighting conditions characterizing the inside of the tunnel. However this causes a high energy demand. Therefore, this case study investigates whether it is possible to minimize the energy demand through the exertion of an automatic new control system regulating the luminous fluxes of artificial sources (guaranteeing the parameters set by the regulation) with respect to the variation of the natural light characterizing the outside. The innovative control systems must be characterized by high reliability levels in order to guarantee conditions which are not dangerous to the driver if an outage occurs and minimize their maintenance costs. To carry out this type of study, the software DIALux was used to simulate a tunnel with a dimming system (with lamps characterized by a high luminous efficiency) regulated by a pre-programmed logic control system (with high Mean Time Between Failure (MTBF) values). The savings obtained enabled the amortization of the solution here suggested in a time interval that makes it an advantageous choice economically speaking.

The increasing importance of a significant reduction of CO₂ emissions in the atmosphere asks the scientific community to find other solutions than fossil fuels with respect to the air conditioning of indoor environments. Nowadays, a priority is represented by the energy expenses reduction, in which residential buildings report one of the highest energy consumption levels among developed countries. The application of alternative energies in residential buildings is an issue debated in the European Commission for the reduction of greenhouse gas emissions with the objective to obtain 20% of the demand from renewable sources. This paper suggests the application of the solar energy stored in solar ponds to air-condition small residential buildings, through the use of absorption machines. A feasibility analysis was carried out in some places characterized by climates that are suitable to make the solution here suggested sustainable from an energetic point of view. Buildings characterized by different boundary surface/volume ratios were examined and the energy saving, the amount of CO₂ that was not emitted in the environment and the return of investments with respect to a more traditional solution were evaluated.

Outdoor thermal comfort is an essential factor of people’s everyday life and deeply affects the habitability of outdoor spaces. However the indices used for its evaluation were usually developed for indoor environments assuming still air conditions and absence of solar radiation and were only later adapted to outdoor spaces. For this reason, in a previous study the Mediterranean Outdoor Comfort Index (MOCI) was developed, which is an empirical index able to estimate the thermal perception of people living in the Mediterranean area. In this study it was compared numerically (by using the data obtained through a field survey) with other selected thermal indices. This comparison, performed in terms of Spearman’s rho correlation coefficient, association Gamma, percentage of correct predictions and cross-tabulation analysis, led to identify the MOCI as the most suitable index to examine outdoor thermal comfort in the interested area. As a matter of fact it showed a total percentage of correct predictions of 35.5%. Good performances were reported even in thermophysiological indices as the Physiological Equivalent Temperature (PET) and Predicted Mean Vote (PMV). Moreover it was revealed that adaptation and acclimatization phenomena tend to have a certain influence as well.

Stimulation elicited by a real world field of view is related to the color, the intensity and the direction of the information reaching the eye: different spectral power distributions of light trigger different responses. An evaluation of the stimulation provided by the field of view can be performed by measuring the spectral radiance with a spectroradiometer and weighting this data with an efficiency curve. Different weights (physical, physiological and psychological) can lead to different analyses and consequently to different results. The proposed method allows an overall and simplified evaluation of the field of view based on spectral and luminance measures and a script that processes the luminous information. The final aim of this approach is to provide further information about the light stimulation reaching the retina and to supply a qualitative evaluation of the field of view, allowing to know how much stimulation is coming from a certain area within the visual field depending on the type of surface, basing on spectral and directional information. This approach can have practical implications, allowing technicians and designers to take into consideration the possible visual fields, in order to properly shape the features of stimulation throughout the day, hence following a field of view-based dynamic design.

The smart and resilient city evolves by slow procedures of mutation without radical changes, increasing the livability of its territory. The value of the city center in a Smart City can increase through urban lighting systems: its elements on the territory can collect and convey data to increase services to city users; the electrical system becomes the so-called Smart Grid. This paper presents a study of smart lighting for a small town, a touristic location inside a nature reserve on the Italian coast. Three different approaches have been proposed, from minimal to more invasive interventions, and their effect on the territory has been investigated. Based on street typology and its surroundings, the work analyzes the opportunity to introduce smart and useful services for the citizens starting from a retrofitting intervention. Smart city capabilities are examined, showing how it is possible to provide new services to the cities through ICT (Information and Communication Technology) without deep changes and simplifying the control of basic city functions. The results evidence an important impact on annual energy costs, suggesting smart grid planning not only for metropolis applications, but also in smaller towns, such as the examined one.

Proper lighting is vital to improve, from an artistic point of view, the surface expanse and decorative detailing of architectural heritage buildings considered valuable. When properly lit, monumental buildings can become to onlookers an essential part of the city. Nowadays, for design planners dealing with the improvement of buildings, whose architectural design should be valorized, the real challenge is to combine the lighting artistic requirements with scrupulous economic management in order to limit the energy demand and to respect the environment. For these reasons, this case study examines the lighting of the monumental façade and the cloister of St. Peter in Chains situated in the Faculty of Engineering of Sapienza University of Rome. The present lighting installation, characterized by metal halides, compact fluorescent and halogen lamps, is compared with an alternative scenario presenting LED lamps and scenographic lighting of the monumental façade. Such comparison is based on the evaluation of the lighting levels for different visual tasks and on energy and maintenance issues; the first analysis was performed through the software DIALux Evo 4.0, whereas the second was performed using ecoCALC. This study leads to the conclusion that the lighting levels of the solution presenting LED lamps are better than those of the present solution, and they comply with current standards. Finally, the higher costs of LED lamp installations and the scenographic lighting of the monumental façade are balanced by lower maintenance costs, with a payback period of seven years.

The goal set by the EU of quasi-zero energy buildings is not easy to reach for a country like Italy, as it holds a wide number of UNESCO sites and most of them are entire historical old towns. This paper focuses on the problem of the improvement of energy performance of historical Italian architecture through simple interventions that respect the building without changing its shape and structure. The work starts from an energy analysis of a building located in the historic center of Tivoli, a town close to Rome. The analysis follows the recommendations of the UNI TS 11300-Part1, which indicates how to evaluate the energy consumptions. The calculations were performed only on the building envelope, based on passive solutions and alternatives. Four passive strategies were examined and applied based on the location of the building and the non-alteration of the structure and the landscape. The obtained results impacted positively on the energy performance of the building: the annual energy saving reached a maximum value of 25%. This work shows how it is possible to improve the energy performance of an existing building achieving a significant energy saving with the respect of the building architecture, shape, function and the surrounding landscape.

The European Union is working on strategies in order to increase the energy efficiency of buildings. A useful solution is to identify the energy performance of buildings through the Energy Performance Certificate (EPC), as it provides information for the comparison of buildings with different architectural typology, shape, design technology and geographic location. However, this tool does not assess the real energy consumption of the building and does not always take into account its impact on the environment. In this work, two different types of analysis were carried out: one based only on the energy efficiency and the other one based on the environmental impact. Those analyses were applied on a standard building, set in three different Italian locations, with the purpose of obtaining cross-related information. After the evaluation of the results, interventions on some parameters (walls insulation, windows frame, filler gas in the insulated glazing) have been identified in order to improve the energy behavior of the building with an acceptable environmental impact. The aim of this paper is to propose a methodology that integrates the EPC with green building rating systems, leading to a more conscious choice of retrofit interventions as a compromise between energy performances and environmental impact.