JNJordan Nielson

Jordan Nielson

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Jordan Nielson has a total of 6 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Numerical Investigations of Reactive Reversible Blade Turbine for Slow Moving Currents

    by Abhay Patil, Jordan Nielson, Tim Allison, Scot Cummings

    A reactive Reversible Blade Turbine (RRBT) is a drag-type hydrokinetic turbine consisting of movable blades designed to pivot around their axes to reduce drag and optimize the power coefficient. RRBT allows for reverse rotation of the opposing blades, with reduced drag during the rotation of the turbine. The blade “reverse slices” through the water to a neutral position and then rests against a stop which causes the turbine to rotate with reduced opposing drag on the opposite side of the turbine shaft. While the construction is simple, there is obscurity surrounding the quantitative gain in performance due to the proposed modification. The current study focuses on the development of a numerical model to quantify RRBT performance gain due to the reactive blade operation. The numerical model employs a sliding mesh model to simulate the single-blade motion in loaded positions to quantify the flow physics and performance estimation. The preliminary outcomes reveal power coefficient values comparable to the existing state of the art, however, peaking at a much lower tip speed ratio. The power coefficient (Cp) estimation of 0.219 using CFD agrees well with the test prediction of 0.2 at 0.32 Tip Speed Ratio. The study concludes with the evaluation and discussion of the performance gain using two different stop locations, and steady-state analysis to provide initial estimation of blade relative motion in reactive modes.

  • Using field data–based large eddy simulation to understand role of atmospheric stability on energy production of wind turbines

    by Jordan Nielson, Kiran Bhaganagar

    A novel and a robust high-fidelity numerical methodology has been developed to realistically estimate the net energy production of full-scale horizontal axis wind turbines in a convective atmospheric boundary layer, for both isolated and multiple wind turbine arrays by accounting for the wake effects between them. Large eddy simulation has been used to understand the role of atmospheric stability in net energy production (annual energy production) of full-scale horizontal axis wind turbines placed in the convective atmospheric boundary layer. The simulations are performed during the convective conditions corresponding to the National Renewable Energy Laboratory field campaign of July 2015. A mathematical framework was developed to incorporate the field-based measurements as boundary conditions for the large eddy simulation by averaging the surface flux over multiple diurnal cycles. The objective of the study is to quantify the role of surface flux in the calculation of energy production for an isolated, two and three wind turbine configuration. The study compares the mean value, +1 standard deviation, and −1 standard deviation from the measured surface flux to demonstrate the role of surface heat flux. The uniqueness of the study is that power deficits from large eddy simulation were used to determine wake losses and obtain a net energy production that accounts for the wake losses. The frequency of stability events, from field measurements, is input into the calculation of an ensemble energy production prediction with wake losses for different wind turbine arrays. The increased surface heat flux increases the atmospheric turbulence into the wind turbines. Higher turbulence results in faster wake recovery by a factor of two. The faster wake recovery rates result in lowering the power deficits from 46% to 28% for the two-turbine array. The difference in net energy production between the +1 and −1 standard deviation (with respect to surface heat flux) simulations was 10% for the two-turbine array and 8% for the three-turbine array. An ensemble net energy production by accounting for the wake losses indicated the overestimation of annual energy production from current practices could be corrected by accounting for variation of surface flux from the mean value.


  • Open Access

    Capturing Day-to-day Diurnal Variations in Stability in the Convective Atmospheric Boundary Layer Using Large Eddy Simulation

    by Jordan Nielson, Kiran Bhaganagar

    Introduction:Large Eddy Simulation (LES) modelers must begin to answer the question of how to better incorporate large datasets into simulations. This question is important because, at a given location, the diurnal, seasonal, and day-to-day variations of atmospheric stability have significant consequences for the power generated by wind turbines. The following study provides a methodology to obtain discrete values of surface flux, inversion height and geostrophic wind for LES using field data over multiple diurnal cycles (averaged over a month) at 12 Local Time (LT) (during the convective ABL). The methodology will allow the discrete LES to quantify the day-to-day variations over multiple diurnal cycles.Methods:The study tests the hypothesis that LES can capture the mean velocity and TKE profiles from the averaged variations in surface heat flux at 12 LT measured in the field (mean, +1 standard deviation, and -1 standard deviation). The discrete LES from the mean, +1 standard deviation, and -1 standard deviation surface heat flux represent the variations in the ABL due to the day-to-day variations in surface heat flux. The method calculates the surface heat flux for the NREL NWTC M5 dataset. The field data were used to generate Probability Density Functions (PDFs) of surface heat flux for the January and July 12 LT. The PDFs are used to select the surface heat fluxes as inputs into the discrete LES.Results / Conclusion:A correlation function between the surface heat flux and the boundary layer height was determined to select the initial inversion height, and the geostrophic departure function was used to determine the geostrophic wind for each surface heat flux. The LES profiles matched the averaged velocity profiles from the field data to 4% and the averaged TKE profiles to 6% and, therefore, validated the methodology. The method allows for further quantification of day-to-day stability variations using LES.