Steve Brown
Research Subjects
Steve Brown has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
A King
Atomic Weapons Establishment, Aldermaston, Reading, Berkshire, RG7 4PR, United Kingdom
1 shared publication- Aled Jones
AWE Plc, Aldermaston, U.K.
1 shared publication - Anthony J. Annunziata
IBM T. J. Watson Research Center 1 IBM-Crocus MRAM Alliance Yorktown Heights, New York 10598, USA
1 shared publication B Galver
L3 Communications, Pulse Sciences Division, San Leandro CA, USA
1 shared publicationB Stringer
Atomic Weapons Establishment, Aldermaston, Reading, Berkshire, RG7 4PR, United Kingdom
1 shared publicationB Whitney
L3 Communications, Pulse Sciences Division, San Leandro CA, USA
1 shared publication
Latest Publications
- 1 September 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (5)
Measurement of CoFeB configurational ordering in magnetic random-access memory stacks using extended x-ray absorption fine structure spectroscopy
Using extended x-ray absorption fine structure spectroscopy (EXAFS), we demonstrate a quantitative method to evaluate the degree of structural order in thin CoFeB-based structures used in spin-transfer-torque magnetic random access memory (STT-MRAM). This method allows us to access a large-area scale (≈1 cm2) for characterization of the relative degree of crystallization of ultrathin CoFeB (≈2 nm) when the composition and thickness of surrounding materials are varied and the presence of other ordered materials complicates XRD analysis. Our EXAFS-based analysis was applied to multiple combinations of metal- and oxide-capped CoFeB layer structures grown on an MgO layer. We show how specific combinations of free layer capping and underlayers can significantly enhance or lower the relative degree of local order of a thin CoFeB layer. The impact of the capping metal layer thickness and the effect of oxide-based capping layers (metal oxides and MgO) are also presented. Among the elemental metals evaluated in the current work, we find zirconium to be the most efficient in enhancing the crystallization of a 2 nm thick CoFeB layer. We also find that the ability to enhance ordering is not dramatically reduced when using metal oxides rather than pure metal capping. Future STT-MRAM stack optimization can be guided by this comprehensive study and by additional measurements using the proposed quantitative method of assessment.
- 1 September 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (5)
Measurement of CoFeB configurational ordering in magnetic random-access memory stacks using extended x-ray absorption fine structure spectroscopy
Using extended x-ray absorption fine structure spectroscopy (EXAFS), we demonstrate a quantitative method to evaluate the degree of structural order in thin CoFeB-based structures used in spin-transfer-torque magnetic random access memory (STT-MRAM). This method allows us to access a large-area scale (≈1 cm2) for characterization of the relative degree of crystallization of ultrathin CoFeB (≈2 nm) when the composition and thickness of surrounding materials are varied and the presence of other ordered materials complicates XRD analysis. Our EXAFS-based analysis was applied to multiple combinations of metal- and oxide-capped CoFeB layer structures grown on an MgO layer. We show how specific combinations of free layer capping and underlayers can significantly enhance or lower the relative degree of local order of a thin CoFeB layer. The impact of the capping metal layer thickness and the effect of oxide-based capping layers (metal oxides and MgO) are also presented. Among the elemental metals evaluated in the current work, we find zirconium to be the most efficient in enhancing the crystallization of a 2 nm thick CoFeB layer. We also find that the ability to enhance ordering is not dramatically reduced when using metal oxides rather than pure metal capping. Future STT-MRAM stack optimization can be guided by this comprehensive study and by additional measurements using the proposed quantitative method of assessment.
- 22 April 2015
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 117 (17) , 17B739
Materials investigation for thermally-assisted magnetic random access memory robust against 400 °C temperatures
Magnetic materials are investigated in order to enable a new type of Thermally Assisted Magnetic Random Access Memory (TAS-MRAM). A TAS-MRAM materials stack that is robust against the 400 °C process temperatures required for embedded integration with complementary metal oxide silicon processes is demonstrated. In unpatterned sheet film stacks, a stable resistance-area product, tunneling magnetoresistance (MR) > 100%, and temperature-dependent exchange bias of 1500 Oe after 400 °C anneal are shown for this stack. It is further shown that by doping the sense and storage layers with Ta using thin laminations of Ta/CoFeB, the moment of each layer can be reduced by more than 40% without a major reduction in MR. In patterned nanopillar devices, it is shown that by reducing the moment of the sense and storage layers with laminations of Ta, and by adding a second MgO barrier, the resistance versus applied field loop quality is maintained, while the read field is reduced by more than 40% and devices survive 108 write cycles without breakdown or significant degradation.
- 22 April 2015
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 117 (17) , 17B739
Materials investigation for thermally-assisted magnetic random access memory robust against 400 °C temperatures
Magnetic materials are investigated in order to enable a new type of Thermally Assisted Magnetic Random Access Memory (TAS-MRAM). A TAS-MRAM materials stack that is robust against the 400 °C process temperatures required for embedded integration with complementary metal oxide silicon processes is demonstrated. In unpatterned sheet film stacks, a stable resistance-area product, tunneling magnetoresistance (MR) > 100%, and temperature-dependent exchange bias of 1500 Oe after 400 °C anneal are shown for this stack. It is further shown that by doping the sense and storage layers with Ta using thin laminations of Ta/CoFeB, the moment of each layer can be reduced by more than 40% without a major reduction in MR. In patterned nanopillar devices, it is shown that by reducing the moment of the sense and storage layers with laminations of Ta, and by adding a second MgO barrier, the resistance versus applied field loop quality is maintained, while the read field is reduced by more than 40% and devices survive 108 write cycles without breakdown or significant degradation.
- 1 June 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21584915,p. 1042-1047
Status of the AWE Hydrus IVA fabrication
The ten-module Hydrus Induction Voltage Adder, designed by L3 Communications - Pulse Sciences Division for AWE, builds on previous IVA experience in the US. Each of the ten modules comprises a 1.4 MV induction cell driven by a laser triggered gas switched Pulse Forming Line (PFL) in order to provide nanosecond order synchronisation, and hence excellent pulse reproducibility. The PFLs are charged by a single Marx through an oil-insulated transmission line. The outputs of the cells are added along a 22 metre long 80 ohm MITL to deliver an 11 MV forward going wave to the e-beam diode. The accelerator will be used for flash radiography by AWE utilising a Self Magnetic Pinch diode as the radiographic source. This diode operates at approximately 40 Ohms with the result that retrapping of the MITL sheath current occurs, reducing the diode voltage to ~ 7.5 MV, but increasing the load current to 200 kA. The detailed PFL design was previously prototyped and has been chosen to tailor the output pulse to compensate for the SMP diode's intra pulse impedance reduction and hence generate a relatively constant voltage during generation of the X-ray flash. The components of the Hydrus IVA are approaching completion at L3 Pulse Sciences at San Leandro, CA. All parts of the IVA are being procured by L-3 PS and delivered to San Leandro for subassembly. The major IVA subassemblies being fabricated comprise the Marx, oil line, PFL, cell, and stalk. Ancillary systems being fabricated comprise the control software, vacuum, water processing, oil processing, magnetic core reset, gas processing, data acquisition, and power supply. Subassemblies and subsystems are subject to a variety of QA tests which include high voltage testing of the Marx and its trigger, and a first-article PFL driving both a dummy load and a first-article cell. The status of the in-progress fabrication and QA testing for each of the major subsystems is described in this paper. The complete system will not be assembled and tested in the US. All components of the IVA are to be delivered as subassemblies to AWE in the UK in mid 2012 for assembly and commissioning.
- 1 June 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21584915,p. 1042-1047
Status of the AWE Hydrus IVA fabrication
The ten-module Hydrus Induction Voltage Adder, designed by L3 Communications - Pulse Sciences Division for AWE, builds on previous IVA experience in the US. Each of the ten modules comprises a 1.4 MV induction cell driven by a laser triggered gas switched Pulse Forming Line (PFL) in order to provide nanosecond order synchronisation, and hence excellent pulse reproducibility. The PFLs are charged by a single Marx through an oil-insulated transmission line. The outputs of the cells are added along a 22 metre long 80 ohm MITL to deliver an 11 MV forward going wave to the e-beam diode. The accelerator will be used for flash radiography by AWE utilising a Self Magnetic Pinch diode as the radiographic source. This diode operates at approximately 40 Ohms with the result that retrapping of the MITL sheath current occurs, reducing the diode voltage to ~ 7.5 MV, but increasing the load current to 200 kA. The detailed PFL design was previously prototyped and has been chosen to tailor the output pulse to compensate for the SMP diode's intra pulse impedance reduction and hence generate a relatively constant voltage during generation of the X-ray flash. The components of the Hydrus IVA are approaching completion at L3 Pulse Sciences at San Leandro, CA. All parts of the IVA are being procured by L-3 PS and delivered to San Leandro for subassembly. The major IVA subassemblies being fabricated comprise the Marx, oil line, PFL, cell, and stalk. Ancillary systems being fabricated comprise the control software, vacuum, water processing, oil processing, magnetic core reset, gas processing, data acquisition, and power supply. Subassemblies and subsystems are subject to a variety of QA tests which include high voltage testing of the Marx and its trigger, and a first-article PFL driving both a dummy load and a first-article cell. The status of the in-progress fabrication and QA testing for each of the major subsystems is described in this paper. The complete system will not be assembled and tested in the US. All components of the IVA are to be delivered as subassemblies to AWE in the UK in mid 2012 for assembly and commissioning.