Akram Raheem Jabur
Research Subjects
Akram Raheem Jabur has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
Noor M. Jalal
4 shared publications- Emad S. Al-Hassani
University of Technology
3 shared publications Fadhil A. Chayad
3 shared publications- Qusay Fadhil Alsalhy
Membrane Technology Research Unit, Chemical Engineering Department, University of Technology-Iraq, Alsinaa Street 52, Baghdad 10066, Iraq
3 shared publications Saja A. Moosa
3 shared publications- Suriani Abu Bakar
Nanotechnology Research Centre, Faculty of Science and Mathematics, Universiti Pendidikan Sultan Idris, Perak, Malaysia
3 shared publications
Latest Publications
- Open Access
- 21 January 2024
- Published by University of Technology, Iraq - DIGITAL COMMONS in Journal of Applied Sciences and Nanotechnology
- Vol. 4 (1) , 1-8
Morphology Characterization of Electrospun Polystyrene Membranes
The polymeric solution concentration is one of the most critical factors in forming of fibers in electrospinning technology. In this study, various polymeric concentrations of thermoplastic polystyrene are used. At the same time, keeping the other electrospinning process operating parameters (such as flow rate, voltage, capillary to collector distance), solution parameters (such as solution conductivity and molecular weight), and environmental conditions (such as temperature and humidity) constant. Field emission scanning electron microscopy was used to investigate the morphological changes that took place on the surface of the fibres and determine the typical fibre diameter. It was found that as the concentration of polystyrene increased from 15% to 30%, the average pore size increased from (0.5µm and 0.44µm) to (2.7µm and 2.6µm). The FT-IR demonstrated the main chemical bonds in polystyrene membranes and the change in peak intensity caused by increasing the polymeric concentration. According to contact angle measurements, which examine the change in hydrophobic properties, the hydrophobicity of membranes decreases as the water contact angle falls from 135 to 116 with increasing the polymeric concentration from 15% to 30%.
- 21 January 2024
- Published by University of Technology, Iraq - DIGITAL COMMONS in Journal of Applied Sciences and Nanotechnology
- Vol. 4 (1) , 1-8
Open AccessMorphology Characterization of Electrospun Polystyrene Membranes
The polymeric solution concentration is one of the most critical factors in forming of fibers in electrospinning technology. In this study, various polymeric concentrations of thermoplastic polystyrene are used. At the same time, keeping the other electrospinning process operating parameters (such as flow rate, voltage, capillary to collector distance), solution parameters (such as solution conductivity and molecular weight), and environmental conditions (such as temperature and humidity) constant. Field emission scanning electron microscopy was used to investigate the morphological changes that took place on the surface of the fibres and determine the typical fibre diameter. It was found that as the concentration of polystyrene increased from 15% to 30%, the average pore size increased from (0.5µm and 0.44µm) to (2.7µm and 2.6µm). The FT-IR demonstrated the main chemical bonds in polystyrene membranes and the change in peak intensity caused by increasing the polymeric concentration. According to contact angle measurements, which examine the change in hydrophobic properties, the hydrophobicity of membranes decreases as the water contact angle falls from 135 to 116 with increasing the polymeric concentration from 15% to 30%.
- Open Access
- 3 March 2023
- Published by Wiley in International Journal of Biomaterials
- Vol. 2023, 1-14
Metallic Implant Surface Activation through Electrospinning Coating of Nanocomposite Fiber for Bone Regeneration
There is a critical need in orthopedic and orthodontic clinics for enhanced implant-bone interface contact to facilitate the quick establishment of a strong and durable connection. Surface modification by bioactive multifunctional materials is a possible way to overcome the poor osteoconductivity and the potential infection of Ti-based implants. Ti-25Zr biometallic alloy was prepared by powder metallurgy technique and then coated by Nano-composite fiber using electrospinning. Ceramic Nanocompound (CaTiO3, BaTiO3) was used as filler material and individually added to polymeric matrices constructed from the blend of polycaprolactone/chitosan. Using optical microscopy, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), Fourier transform infrared spectroscopy (FTIR), and wettability, respectively, the morphology, chemical analysis, surface roughness, and contact angle measurements of the samples were evaluated. The result shows a significant improvement in cell viability, proliferation, and ALP activity for coated samples compared to noncoated samples. PCL/Chitosan/Nano-CaTiO3 (CA1) recorded remarkable enhancement from the surface-coated samples, demonstrating a significantly higher cell viability value after seven days of MC3T3-E1 cell culture, reaching 271.56±13.15, and better cell differentiation with ALP activity reaching 5.61±0.35 fold change for the same culture time. PCL/Chitosan/Nano-BaTiO3 (BA1) also shows significant improvement in cell viability by 181.63±17.87 and has ALP activity of 3.97±0.67 fold change. For coated samples, cell proliferation likewise exhibits a considerable temporal increase; the improvement reaches 237.53 for (CA1) and 125.16 for (BA1) in comparison with uncoated samples (bare Ti-25Zr). The coated samples resist bacteria in the antibacterial test compared to the noncoated samples with no inhibition zone. This behavior suggests that a Nanocomposite fiber coat containing an active ceramic Nanocompound (CaTiO3, BaTiO3) promotes cell growth and holds promise for orthodontic and orthopedic bioapplication.
- 3 March 2023
- Published by Wiley in International Journal of Biomaterials
- Vol. 2023, 1-14
Open AccessMetallic Implant Surface Activation through Electrospinning Coating of Nanocomposite Fiber for Bone Regeneration
There is a critical need in orthopedic and orthodontic clinics for enhanced implant-bone interface contact to facilitate the quick establishment of a strong and durable connection. Surface modification by bioactive multifunctional materials is a possible way to overcome the poor osteoconductivity and the potential infection of Ti-based implants. Ti-25Zr biometallic alloy was prepared by powder metallurgy technique and then coated by Nano-composite fiber using electrospinning. Ceramic Nanocompound (CaTiO3, BaTiO3) was used as filler material and individually added to polymeric matrices constructed from the blend of polycaprolactone/chitosan. Using optical microscopy, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), Fourier transform infrared spectroscopy (FTIR), and wettability, respectively, the morphology, chemical analysis, surface roughness, and contact angle measurements of the samples were evaluated. The result shows a significant improvement in cell viability, proliferation, and ALP activity for coated samples compared to noncoated samples. PCL/Chitosan/Nano-CaTiO3 (CA1) recorded remarkable enhancement from the surface-coated samples, demonstrating a significantly higher cell viability value after seven days of MC3T3-E1 cell culture, reaching 271.56±13.15, and better cell differentiation with ALP activity reaching 5.61±0.35 fold change for the same culture time. PCL/Chitosan/Nano-BaTiO3 (BA1) also shows significant improvement in cell viability by 181.63±17.87 and has ALP activity of 3.97±0.67 fold change. For coated samples, cell proliferation likewise exhibits a considerable temporal increase; the improvement reaches 237.53 for (CA1) and 125.16 for (BA1) in comparison with uncoated samples (bare Ti-25Zr). The coated samples resist bacteria in the antibacterial test compared to the noncoated samples with no inhibition zone. This behavior suggests that a Nanocomposite fiber coat containing an active ceramic Nanocompound (CaTiO3, BaTiO3) promotes cell growth and holds promise for orthodontic and orthopedic bioapplication.
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2787 (1)
The effect of Ni-Ti ultrafine particles addition on the elongation properties of the PVA electrospun fibers
Nanofibers are an attractive technology for various applications, especially in the medical field. Different nanofibers are fabricated successfully by electrospinning techniques, including polymers, ceramics, metals, and composites. In this study, the PVA/ ultrafine nickel-titanium (Ni-Ti) composite nanofibers are prepared by a simple direct doping method for biomedical application. The mechanical properties of the electrospun PVA/ Ni-Ti doped particles are characterized by using a tensile test. Composite nanofibers of (0.5 and 1 wt. %) Ni-Ti/ PVA showed an enhancement in elongation properties compared to the pure PVA electrospun fibers. The FESEM images of the prepared electrospun fibers showed uniform and smooth fibers. The tensile test showed an improvement in elongation properties by Ni-Ti ultrafine doping.
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2787 (1)
Open AccessThe effect of Ni-Ti ultrafine particles addition on the elongation properties of the PVA electrospun fibers
Nanofibers are an attractive technology for various applications, especially in the medical field. Different nanofibers are fabricated successfully by electrospinning techniques, including polymers, ceramics, metals, and composites. In this study, the PVA/ ultrafine nickel-titanium (Ni-Ti) composite nanofibers are prepared by a simple direct doping method for biomedical application. The mechanical properties of the electrospun PVA/ Ni-Ti doped particles are characterized by using a tensile test. Composite nanofibers of (0.5 and 1 wt. %) Ni-Ti/ PVA showed an enhancement in elongation properties compared to the pure PVA electrospun fibers. The FESEM images of the prepared electrospun fibers showed uniform and smooth fibers. The tensile test showed an improvement in elongation properties by Ni-Ti ultrafine doping.
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2769 (1)
Improving the compressive and bending properties of cement by reinforcing PVA fibers containing nitinol nanopowder
Fibers are utilized in a variety of ways to reinforce cement products (such as concrete). The behavior of shape memory alloys SMA nanofiber reinforced cement effect is the subject of this research. The shape memory alloy used in this investigation is NiTi. Cement is slump tested, is put to the test for seven days. SMA nanofibers are added to the cement mix at a constant rate of 4% wt. SAM micro powder and SAM microfiber reinforced cement are also made,mechanical parameters such as compressive strength and and bending strength are examined for 7 days. Results are compared to SMA nanofiber reinforced cement. cement reinforced with 4% nitinal PVA nanofibers improved Compressive strength to 47 MPa comparer with 18, MPa for standard cement-sand, while decrees deflection to 0.048mm compare with 0.11,0.249 and 0.26 for standard cement-sand, nitinol to cement and microfiber /standered cement sample respectively.
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2769 (1)
Open AccessImproving the compressive and bending properties of cement by reinforcing PVA fibers containing nitinol nanopowder
Fibers are utilized in a variety of ways to reinforce cement products (such as concrete). The behavior of shape memory alloys SMA nanofiber reinforced cement effect is the subject of this research. The shape memory alloy used in this investigation is NiTi. Cement is slump tested, is put to the test for seven days. SMA nanofibers are added to the cement mix at a constant rate of 4% wt. SAM micro powder and SAM microfiber reinforced cement are also made,mechanical parameters such as compressive strength and and bending strength are examined for 7 days. Results are compared to SMA nanofiber reinforced cement. cement reinforced with 4% nitinal PVA nanofibers improved Compressive strength to 47 MPa comparer with 18, MPa for standard cement-sand, while decrees deflection to 0.048mm compare with 0.11,0.249 and 0.26 for standard cement-sand, nitinol to cement and microfiber /standered cement sample respectively.
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2769 (1) , 020065
Morphology of polystyrene nano-fiber membranes reinforced with copper oxide and zirconium oxide nanoparticles as a sulfur absorbent materials
The electrospinning technique is used to produce composite materials in the form of submicron and nano fibers membranes and then characterized and evaluated pro
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2769 (1) , 020065
Open AccessMorphology of polystyrene nano-fiber membranes reinforced with copper oxide and zirconium oxide nanoparticles as a sulfur absorbent materials
The electrospinning technique is used to produce composite materials in the form of submicron and nano fibers membranes and then characterized and evaluated pro
- Open Access
- 1 December 2022
- Published by University of Technology, Iraq - DIGITAL COMMONS in Engineering and Technology Journal
- Vol. 40 (12) , 1-12
Evaluation of PCL Electrospun Scaffolds Concentration on Metformin Hydrochloride Release Ratio
The study investigates the effect of polycaprolactone (PCL) concentration on the metformin hydrochloride (MH) release ratio of electrospun nanofiber scaffolds. Blend and emulsion electrospinning are used to produce the scaffolds. The performance of nanofibrous scaffolds was evaluated by morphology (Field Emission Scanning Electron Microscopy, FESEM), chemical (Fourier Transform Infrared Spectroscopy, FTIR), thermal (Differential Scanning Calorimetry, DSC), wettability, porosity, mechanical tests, and in vitro drug release. The average fiber diameter ranged from (189.29-2893.93 nm) according to the FESEM results, and it increased with PCL concentration. The average fiber diameter of the electrospun scaffold, prepared by the blend method (259.64±6.1 nm), is lower than that of the electrospun scaffold produced by the emulsion method (487.45±22.53 nm). Melting points of all drug-loaded scaffolds were identical to those of pure PCL polymer. Compared with blend electrospun nanofibers, emulsion electrospun nanofibers showed a marked increase in hydrophilicity. The tensile strength indicated an improvement in the mechanical properties with a decrease in the average fiber diameter. Moreover, the results show that the release of Metformin hydrochloride decreases with the concentration of polycaprolactone. Total MH release from (5% w/v) PCL-MH fibrous scaffolds for three-week was 71.11 % and 93.91 % from the emulsion and blend methods, respectively. The drug release ratio is lower in emulsion electrospinning than in blend because the drug is encapsulated by polymer and surfactant, which improves control and long-term drug delivery system DDS.
- 1 December 2022
- Published by University of Technology, Iraq - DIGITAL COMMONS in Engineering and Technology Journal
- Vol. 40 (12) , 1-12
Open AccessEvaluation of PCL Electrospun Scaffolds Concentration on Metformin Hydrochloride Release Ratio
The study investigates the effect of polycaprolactone (PCL) concentration on the metformin hydrochloride (MH) release ratio of electrospun nanofiber scaffolds. Blend and emulsion electrospinning are used to produce the scaffolds. The performance of nanofibrous scaffolds was evaluated by morphology (Field Emission Scanning Electron Microscopy, FESEM), chemical (Fourier Transform Infrared Spectroscopy, FTIR), thermal (Differential Scanning Calorimetry, DSC), wettability, porosity, mechanical tests, and in vitro drug release. The average fiber diameter ranged from (189.29-2893.93 nm) according to the FESEM results, and it increased with PCL concentration. The average fiber diameter of the electrospun scaffold, prepared by the blend method (259.64±6.1 nm), is lower than that of the electrospun scaffold produced by the emulsion method (487.45±22.53 nm). Melting points of all drug-loaded scaffolds were identical to those of pure PCL polymer. Compared with blend electrospun nanofibers, emulsion electrospun nanofibers showed a marked increase in hydrophilicity. The tensile strength indicated an improvement in the mechanical properties with a decrease in the average fiber diameter. Moreover, the results show that the release of Metformin hydrochloride decreases with the concentration of polycaprolactone. Total MH release from (5% w/v) PCL-MH fibrous scaffolds for three-week was 71.11 % and 93.91 % from the emulsion and blend methods, respectively. The drug release ratio is lower in emulsion electrospinning than in blend because the drug is encapsulated by polymer and surfactant, which improves control and long-term drug delivery system DDS.
- 18 May 2021
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 886, 183-188
Preparation and Physical Properties of PCL-Metoprolol Tartrate Electrospun Nanofibers as Drug Delivery System
Electrospinning is considered a promising technology for encapsulating and loading various drugs into nanofibers. Metoprolol tartrate (MPT), hydrophilic therapy, was used as model drug. Metoprolol tartrate was loaded into poly(ɛ-caprolactone) (PCL) via blend and emulsion electospinning. The preparation processes, morphology, chemical structure thermal properties were evaluated. FESEM showed that emulsion electospinning produce larger fiber diameters(301.775nm) when compared to fibers produced by blend electrospinning(112.463, 249.34)nm, the PCL/ span 80 and MPT-PCL by emulsion method which have high fiber diameter than pure PCL and MPT-PCL by blend method and the Tm of pure PCL nanofibers and all drug loaded scaffolds are around 60°C from DSC test, water contact angle to pure PCL electrospun mats hydrophobic character (126.2°), while PCL/span 80, and PCL-drug nanofiber mats showed hydrophilic character. Our study demonstrated the possibility of using electrospinning with a promising good potential toward sustained and controlled drug delivery system.
- 18 May 2021
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 886, 183-188
Preparation and Physical Properties of PCL-Metoprolol Tartrate Electrospun Nanofibers as Drug Delivery System
Electrospinning is considered a promising technology for encapsulating and loading various drugs into nanofibers. Metoprolol tartrate (MPT), hydrophilic therapy, was used as model drug. Metoprolol tartrate was loaded into poly(ɛ-caprolactone) (PCL) via blend and emulsion electospinning. The preparation processes, morphology, chemical structure thermal properties were evaluated. FESEM showed that emulsion electospinning produce larger fiber diameters(301.775nm) when compared to fibers produced by blend electrospinning(112.463, 249.34)nm, the PCL/ span 80 and MPT-PCL by emulsion method which have high fiber diameter than pure PCL and MPT-PCL by blend method and the Tm of pure PCL nanofibers and all drug loaded scaffolds are around 60°C from DSC test, water contact angle to pure PCL electrospun mats hydrophobic character (126.2°), while PCL/span 80, and PCL-drug nanofiber mats showed hydrophilic character. Our study demonstrated the possibility of using electrospinning with a promising good potential toward sustained and controlled drug delivery system.
- 18 May 2021
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 886, 86-96
Polystyrene/MWCNTs Nanofiber Membranes characterizations in Reducing Sulfur Content in Crude Oil
Composite material membranes as fibers were produced by using electrospinning technology and these membranes characterized and evaluated their properties and performance in this research. Multi-walled carbon nanotubes impregnated in a polystyrene matrix to produce the composite membranes. The hydrophobicity of the membrane was improved by the composite concept with multi-walled carbon nanotubes because of the migration of MWCNTs into fiber structure with membranes. Field emission scanning electron microscopy used to study the morphologies of the membranes and illustrated the average diameters of produced fibers which found about 1.68-3.2 µm and average pore size which found about 3.6 – 4.7 µm for composite membranes and showed an increasing in fibers diameter and pore size with increasing of the MWCNTs amount while the membranes porosity still high percentage about 98%. Also the polystyrene with MWCNTs showed the ability of membranes to decrease the sulfur content from 2.8% for crude oil and reach to about 1.6 % with polystyrene/2% MWCNTs.
- 18 May 2021
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 886, 86-96
Polystyrene/MWCNTs Nanofiber Membranes characterizations in Reducing Sulfur Content in Crude Oil
Composite material membranes as fibers were produced by using electrospinning technology and these membranes characterized and evaluated their properties and performance in this research. Multi-walled carbon nanotubes impregnated in a polystyrene matrix to produce the composite membranes. The hydrophobicity of the membrane was improved by the composite concept with multi-walled carbon nanotubes because of the migration of MWCNTs into fiber structure with membranes. Field emission scanning electron microscopy used to study the morphologies of the membranes and illustrated the average diameters of produced fibers which found about 1.68-3.2 µm and average pore size which found about 3.6 – 4.7 µm for composite membranes and showed an increasing in fibers diameter and pore size with increasing of the MWCNTs amount while the membranes porosity still high percentage about 98%. Also the polystyrene with MWCNTs showed the ability of membranes to decrease the sulfur content from 2.8% for crude oil and reach to about 1.6 % with polystyrene/2% MWCNTs.
- 14 July 2020
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1002, 84-94
Effect of Iodine Addition on Improving the Electrical Conductivity and Activation Energy of Electrospun PMMA Thin Films
Conductive polymer films were prepared from poly (methyl methacrylate) PMMA with (0, 0.3, 0.5, 0.7, and 0.9) wt. % of iodine, using electrospinning technique. A decrease was noticed in the polymer solution viscosity with increasing the iodine weight percentage while both surface tension and electrical conductivity of the polymer solutions were increased .The structure and morphology of the prepared films were characterized by scanning electron microscopy SEM, the average fiber diameter measured statistically from the SEM images and was equal to 800 nm for PMMA with 0.7 wt. % iodine thin film, and 400 nm for the pure PMMA thin film. The electrical conductivity was enhanced for the electrospun films with increasing iodine concentration, from (29.5518× 10 -9 S/cm) for pure PMMA film to (59.3725× 10 -9 S/cm) for PMMA with 0.9 wt. % of iodine additives at room temperature. Activation energy decreased from 0.4483 e.V for pure PMMA to 0.43029 e.V for PMMA with 0.9 wt. % iodine.
- 14 July 2020
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1002, 84-94
Effect of Iodine Addition on Improving the Electrical Conductivity and Activation Energy of Electrospun PMMA Thin Films
Conductive polymer films were prepared from poly (methyl methacrylate) PMMA with (0, 0.3, 0.5, 0.7, and 0.9) wt. % of iodine, using electrospinning technique. A decrease was noticed in the polymer solution viscosity with increasing the iodine weight percentage while both surface tension and electrical conductivity of the polymer solutions were increased .The structure and morphology of the prepared films were characterized by scanning electron microscopy SEM, the average fiber diameter measured statistically from the SEM images and was equal to 800 nm for PMMA with 0.7 wt. % iodine thin film, and 400 nm for the pure PMMA thin film. The electrical conductivity was enhanced for the electrospun films with increasing iodine concentration, from (29.5518× 10 -9 S/cm) for pure PMMA film to (59.3725× 10 -9 S/cm) for PMMA with 0.9 wt. % of iodine additives at room temperature. Activation energy decreased from 0.4483 e.V for pure PMMA to 0.43029 e.V for PMMA with 0.9 wt. % iodine.
- 25 March 2020
- Published by University of Technology in Engineering and Technology Journal
- Vol. 38 (3A) , 431-439
Multiwall Carbon Nanotube / Polyvinyl Alcohol Nanofibers Film, Electrical Conductivity Improvement
- 25 March 2020
- Published by University of Technology in Engineering and Technology Journal
- Vol. 38 (3A) , 431-439
Multiwall Carbon Nanotube / Polyvinyl Alcohol Nanofibers Film, Electrical Conductivity Improvement