Hanlin Xie
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Hanlin Xie has a total of 68 co-authors. Here are the top co-authors by number of shared publications:
- Geok Ing Ng
Energy Research Institute Nanyang Technological University 1 CleanTech Loop, #06‐04 Singapore 637141 Republic of Singapore
10 shared publications - Hanchao Li
School of Electrical and Electronic Engineering, Nanyang Technological University, Jurong West, Singapore
6 shared publications - Qingyun Xie
Microsystems Technology Laboratories, Massachusetts Institute of Technology, Cambridge, MA, USA
6 shared publications - Siyu Liu
Energy Research Institute @ NTU, Nanyang Technological University, Nanyang Ave, Singapore
6 shared publications - Yihao Zhuang
Energy Research Institute, Nanyang Technological University, Jurong West, Singapore
6 shared publications Geok Ing Ng
Institute of Microelectronics (IME), Agency for Science, Technology and Research (A*STAR) 2 , 2 Fusionopolis Way, Innovis #08-02, 138634
4 shared publications
Latest Publications
- 9 March 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (10)
Inelastic-stress-induced threshold instability and mobility degradation in AlN/GaN MIS-HEMTs on Si
This work investigates the impact of stress-induced effects on the stability of AlN/GaN MIS-HEMTs on Si employing PECVD-SiN as a passivation layer. DC and temperature-dependent C–V/I–V measurements together with technology computer-aided design simulations are used to correlate stress state, defect behavior, and channel transport. As-deposited PECVD-SiN introduces strong inelastic stress that compresses the 2DEG near the GaN surface and drives an anomalous reverse shift of the threshold voltage of ∼−0.3 V between 300 and 475 K, with room-temperature mobility limited to ∼700 cm2 V−1 s−1 by remote scattering. Arrhenius analysis of the drain current yields an activation energy Ea = 0.059 eV, attributed to thermally activated charging and restructuring of bulk and interface defects coupled to the stress field. Post-passivation annealing at 450 °C largely relaxes the inelastic component, broadens the potential well, and reduces Ea to 0.019 eV. The mobility increases to ∼1260 cm2 V−1 s−1 and exhibits a polar optical phonon-like temperature dependence, while the VTH–T behavior changes to a weak positive coefficient. These results offer insights on the temperature stability of stress-induced GaN MIS-HEMTs from a material perspective.
- 9 March 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (10)
Inelastic-stress-induced threshold instability and mobility degradation in AlN/GaN MIS-HEMTs on Si
This work investigates the impact of stress-induced effects on the stability of AlN/GaN MIS-HEMTs on Si employing PECVD-SiN as a passivation layer. DC and temperature-dependent C–V/I–V measurements together with technology computer-aided design simulations are used to correlate stress state, defect behavior, and channel transport. As-deposited PECVD-SiN introduces strong inelastic stress that compresses the 2DEG near the GaN surface and drives an anomalous reverse shift of the threshold voltage of ∼−0.3 V between 300 and 475 K, with room-temperature mobility limited to ∼700 cm2 V−1 s−1 by remote scattering. Arrhenius analysis of the drain current yields an activation energy Ea = 0.059 eV, attributed to thermally activated charging and restructuring of bulk and interface defects coupled to the stress field. Post-passivation annealing at 450 °C largely relaxes the inelastic component, broadens the potential well, and reduces Ea to 0.019 eV. The mobility increases to ∼1260 cm2 V−1 s−1 and exhibits a polar optical phonon-like temperature dependence, while the VTH–T behavior changes to a weak positive coefficient. These results offer insights on the temperature stability of stress-induced GaN MIS-HEMTs from a material perspective.
- 16 February 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (7)
Mechanistic insight and demonstration of antiferroelectric-gated enhancement-mode GaN HEMTs
This work presents mechanistic insight into polarization-assisted charge trapping in GaN HEMTs and demonstrates an enhancement-mode (e-mode) device employing an antiferroelectric (AFE) Hf0.2Zr0.8O2 gate stack (AFE-HEMT). The AFE gate stack, featuring enhanced charge trapping capability and zero remnant polarization (Pr), allows complete utilization of trapped electrons for channel depletion, resulting in a stronger positive threshold voltage (VTH) shift compared with the ferroelectric (FE) gate stack. The AFE-HEMT achieves a VTH of 1.9 V, with a maximum drain current (ID_MAX) of 481 mA/mm and an on-resistance (RON) of 7.4 Ω mm. Incorporating a floating gate structure (AFE-FG-HEMT) further enhances VTH to 2.7 V with an RON of 6.5 Ω mm, significantly improves charge retention, and yields negligible VTH shift during positive bias stress, demonstrating a compelling pathway toward stable, normally off GaN power devices.
- 16 February 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (7)
Mechanistic insight and demonstration of antiferroelectric-gated enhancement-mode GaN HEMTs
This work presents mechanistic insight into polarization-assisted charge trapping in GaN HEMTs and demonstrates an enhancement-mode (e-mode) device employing an antiferroelectric (AFE) Hf0.2Zr0.8O2 gate stack (AFE-HEMT). The AFE gate stack, featuring enhanced charge trapping capability and zero remnant polarization (Pr), allows complete utilization of trapped electrons for channel depletion, resulting in a stronger positive threshold voltage (VTH) shift compared with the ferroelectric (FE) gate stack. The AFE-HEMT achieves a VTH of 1.9 V, with a maximum drain current (ID_MAX) of 481 mA/mm and an on-resistance (RON) of 7.4 Ω mm. Incorporating a floating gate structure (AFE-FG-HEMT) further enhances VTH to 2.7 V with an RON of 6.5 Ω mm, significantly improves charge retention, and yields negligible VTH shift during positive bias stress, demonstrating a compelling pathway toward stable, normally off GaN power devices.
- 22 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (3) , 482-485
GaN-on-Si HEMT Technology for mm-Wave Mobile T/R Modules Demonstrating Concurrent High Efficiency (>60%) and Low Noise (<1.2 dB)
This Letter reports a GaN-on-Si HEMT technology with 60 to 150 nm T-gate achieving simultaneous high efficiency and low noise at low voltage (3−6 V) RF operation, suitable for monolithic integrated FR2 mobile Transmit/Receive (T/R) modules. At 30 GHz and VDS = 5 V, in continuous wave operation, the fabricated Lg = 100 nm device delivered a saturated output power of 1.2 W/mm with a record-high peak power-added efficiency (PAE) of 62% while maintaining a state-of-the-art minimum noise figure (NFmin) of 1.1 dB. Enabled by the optimized epitaxial structure and fabrication process, the proposed technology, even with moderate scaling, offers a cost-effective solution for FR2 T/R modules.
- 22 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (3) , 482-485
GaN-on-Si HEMT Technology for mm-Wave Mobile T/R Modules Demonstrating Concurrent High Efficiency (>60%) and Low Noise (<1.2 dB)
This Letter reports a GaN-on-Si HEMT technology with 60 to 150 nm T-gate achieving simultaneous high efficiency and low noise at low voltage (3−6 V) RF operation, suitable for monolithic integrated FR2 mobile Transmit/Receive (T/R) modules. At 30 GHz and VDS = 5 V, in continuous wave operation, the fabricated Lg = 100 nm device delivered a saturated output power of 1.2 W/mm with a record-high peak power-added efficiency (PAE) of 62% while maintaining a state-of-the-art minimum noise figure (NFmin) of 1.1 dB. Enabled by the optimized epitaxial structure and fabrication process, the proposed technology, even with moderate scaling, offers a cost-effective solution for FR2 T/R modules.
- 4 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (11) , 2066-2069
BEOL-Compatible Amorphous Oxide Semiconductor High-Voltage Transistors Achieving BFoM Beyond the GaAs Limit
Leveraging an offset top-gate (OTG) design and ALD-treated indium-tin oxide (ITO) channels, we present high-performance BEOL-compatible amorphous oxide semiconductor (AOS) high-voltage (HV) field-effect transistors (FETs). A long-channel (LC) FET features the highest Baliga’s figure of merit (BFoM) of 0.361 GW/cm2 among all AOS FETs, surpassing the one-dimensional GaAs limit. Additionally, a short-channel (SC) HV FET achieves a record-low specific on-state resistance (Ron, sp) of 9.15 × 10-2 mΩ·cm2. These results highlight the potential of AOS FETs for enabling high power density and efficiency in on-die power management and periphery applications for monolithic 3D integrated circuits (M3DICs).
- 4 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (11) , 2066-2069
BEOL-Compatible Amorphous Oxide Semiconductor High-Voltage Transistors Achieving BFoM Beyond the GaAs Limit
Leveraging an offset top-gate (OTG) design and ALD-treated indium-tin oxide (ITO) channels, we present high-performance BEOL-compatible amorphous oxide semiconductor (AOS) high-voltage (HV) field-effect transistors (FETs). A long-channel (LC) FET features the highest Baliga’s figure of merit (BFoM) of 0.361 GW/cm2 among all AOS FETs, surpassing the one-dimensional GaAs limit. Additionally, a short-channel (SC) HV FET achieves a record-low specific on-state resistance (Ron, sp) of 9.15 × 10-2 mΩ·cm2. These results highlight the potential of AOS FETs for enabling high power density and efficiency in on-die power management and periphery applications for monolithic 3D integrated circuits (M3DICs).
- 21 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (10) , 1749-1752
GaN-on-Si HEMT for D-Band Power Amplification Demonstrating 0.67 W/mm at 10 V
This Letter reports power amplification by a GaN-on-Si high electron mobility transistor (HEMT) in D-band. An AlN/GaN/AlGaN-on-Si metal-insulator-semiconductor (MIS)-HEMT with ${L}_{g}=140$ nm achieved ${I}_{\textit {dmax}}=2.0$ A/mm, ${g}_{\textit {mmax}}=0.65$ S/mm, and ${f}_{T}$ / ${f}_{\textit {max}}=112$ / 205 GHz. Load-pull at 123 GHz (continuous wave, CW) demonstrated a maximum output power ( ${P}_{\textit {out}}\text {)}$ of 0.67 W/mm at a quiescent drain bias ( ${V}_{\textit {ds}}\text {)}$ of 10 V. The peak power-added efficiency (PAE) of 5.3 % was achieved at ${P}_{\textit {out}}$ of 0.36 W/mm ( ${V}_{\textit {ds}}=5$ V). To the best of the authors’ knowledge, this demonstration marks the highest frequency (and the first-time reaching D-band) in power amplification among published GaN-on-Si HEMTs, therefore revealing the promising potential of GaN-on-Si electronics for sub-THz 6G communication.
- 21 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (10) , 1749-1752
GaN-on-Si HEMT for D-Band Power Amplification Demonstrating 0.67 W/mm at 10 V
This Letter reports power amplification by a GaN-on-Si high electron mobility transistor (HEMT) in D-band. An AlN/GaN/AlGaN-on-Si metal-insulator-semiconductor (MIS)-HEMT with ${L}_{g}=140$ nm achieved ${I}_{\textit {dmax}}=2.0$ A/mm, ${g}_{\textit {mmax}}=0.65$ S/mm, and ${f}_{T}$ / ${f}_{\textit {max}}=112$ / 205 GHz. Load-pull at 123 GHz (continuous wave, CW) demonstrated a maximum output power ( ${P}_{\textit {out}}\text {)}$ of 0.67 W/mm at a quiescent drain bias ( ${V}_{\textit {ds}}\text {)}$ of 10 V. The peak power-added efficiency (PAE) of 5.3 % was achieved at ${P}_{\textit {out}}$ of 0.36 W/mm ( ${V}_{\textit {ds}}=5$ V). To the best of the authors’ knowledge, this demonstration marks the highest frequency (and the first-time reaching D-band) in power amplification among published GaN-on-Si HEMTs, therefore revealing the promising potential of GaN-on-Si electronics for sub-THz 6G communication.
- 21 May 2025
- Published by Wiley in Physica Status Solidi (a)
- Vol. 222 (23)
Trapping Effect in AlN/GaN/AlGaN High‐Electron‐Mobility Transistors Revealed by Tristate Pulse IV Technique
This work presents a novel application of the tristate pulse IV technique to investigate the back barrier (BB)‐associated trapping effects in high‐electron‐mobility transistors (HEMTs) fabricated on an AlN/GaN/AlGaN‐on‐Si epitaxial structure. By incorporating the distinct Pre‐state, this technique enables fast characterization of trap emission while minimizing self‐heating and fast‐activated trap influences, as well as the characterization of deep‐region traps in high‐frequency HEMTs without irreversible damage. Through varying the period and stress conditions of the Pre‐state, the origin of the current collapse is identified as traps located at the channel/BB interface with asymmetric fast capture and slow emission characteristics. The proposed application of the tristate pulse IV technique provides additional insights on trapping effect, reliability, and epitaxy, which are essential for improving high‐frequency power transistors.
- 21 May 2025
- Published by Wiley in Physica Status Solidi (a)
- Vol. 222 (23)
Trapping Effect in AlN/GaN/AlGaN High‐Electron‐Mobility Transistors Revealed by Tristate Pulse IV Technique
This work presents a novel application of the tristate pulse IV technique to investigate the back barrier (BB)‐associated trapping effects in high‐electron‐mobility transistors (HEMTs) fabricated on an AlN/GaN/AlGaN‐on‐Si epitaxial structure. By incorporating the distinct Pre‐state, this technique enables fast characterization of trap emission while minimizing self‐heating and fast‐activated trap influences, as well as the characterization of deep‐region traps in high‐frequency HEMTs without irreversible damage. Through varying the period and stress conditions of the Pre‐state, the origin of the current collapse is identified as traps located at the channel/BB interface with asymmetric fast capture and slow emission characteristics. The proposed application of the tristate pulse IV technique provides additional insights on trapping effect, reliability, and epitaxy, which are essential for improving high‐frequency power transistors.
- 1 March 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (11)
Improved device performance in in situ SiNx/AlN/GaN MIS-HEMTs with ex situ Al2O3 passivation at elevated temperatures
In the present work, the role of ex situ Al2O3 passivation in in situ SiNx/AlN/GaN metal–insulator–semiconductor high-electron-mobility transistors (MIS-HEMTs) to boost device performance and thermal stability during the high-temperature operations has been thoroughly investigated. At room temperature (RT), the MIS-HEMT fabricated with an atomic layer deposited (ALD)-Al2O3 (MIS-HEMT B) exhibits higher maximum drain current (Id,max), peak transconductance (gm,max), and lower subthreshold slope (SS) and gate leakage current compared to MIS-HEMT A fabricated without ex situ Al2O3, signifying the effectiveness of the ALD-Al2O3 layer to passivate severe surface states. Of note, when the temperature rises from 298 to 423 K, the values of Id,max and gm,max decrease noticeably, while SS and gate leakage current increase considerably in both MIS-HEMTs A and B. However, MIS-HEMT B demonstrates a lower degradation rate in various device properties at 423 K compared to MIS-HEMT A, implying that ALD-Al2O3 passivation improves thermal stability. Additionally, ALD-Al2O3 passivation reduces the interface state density from 7.48 × 1012 to 5.3 × 1012 cm−2 eV−1, highlighting its critical role in improving overall device performance.
- 1 March 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (11)
Improved device performance in in situ SiNx/AlN/GaN MIS-HEMTs with ex situ Al2O3 passivation at elevated temperatures
In the present work, the role of ex situ Al2O3 passivation in in situ SiNx/AlN/GaN metal–insulator–semiconductor high-electron-mobility transistors (MIS-HEMTs) to boost device performance and thermal stability during the high-temperature operations has been thoroughly investigated. At room temperature (RT), the MIS-HEMT fabricated with an atomic layer deposited (ALD)-Al2O3 (MIS-HEMT B) exhibits higher maximum drain current (Id,max), peak transconductance (gm,max), and lower subthreshold slope (SS) and gate leakage current compared to MIS-HEMT A fabricated without ex situ Al2O3, signifying the effectiveness of the ALD-Al2O3 layer to passivate severe surface states. Of note, when the temperature rises from 298 to 423 K, the values of Id,max and gm,max decrease noticeably, while SS and gate leakage current increase considerably in both MIS-HEMTs A and B. However, MIS-HEMT B demonstrates a lower degradation rate in various device properties at 423 K compared to MIS-HEMT A, implying that ALD-Al2O3 passivation improves thermal stability. Additionally, ALD-Al2O3 passivation reduces the interface state density from 7.48 × 1012 to 5.3 × 1012 cm−2 eV−1, highlighting its critical role in improving overall device performance.
- 21 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (12) , 2315-2318
AlN/GaN/AlGaN-on-Si HEMT Achieving 1.3 W/mm at 5 V for 5G FR2 Handsets
This Letter reports a double heterostructure (DH) AlN/GaN/AlGaN-on-Si HEMT, which has been proposed, for low voltage (LV, ≤5 V) RF operation. The proposed transistor shows excellent DC ( Idmax =1.9 A/mm, gmmax =0.66 S/mm) and RF small-signal characteristics ( fT/fmax =145/195 GHz). Continuous-wave (CW) load-pull measurements at 30 GHz yield Psat of 0.6 (1.3) W/mm at Vds of 3.5 (5) V, and peak power-added efficiency (PAE) of 43% (42%). To the best of the authors’ knowledge, the Psat values are the highest reported for LV GaN-on-Si HEMTs in 5G FR2, despite the use of conventional alloyed contacts and a gate length ( Lg ) of 120 nm. Furthermore, among published LV GaN-on-Si HEMTs, the proposed transistor achieves a desired combination of saturation velocity ( vsat ) and knee voltage ( Vknee ), which are critical factors for LV power amplification. The results reflect the promising potential of the proposed heterostructure to achieve high transmit power in 5G FR2 handsets.
- 21 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (12) , 2315-2318
AlN/GaN/AlGaN-on-Si HEMT Achieving 1.3 W/mm at 5 V for 5G FR2 Handsets
This Letter reports a double heterostructure (DH) AlN/GaN/AlGaN-on-Si HEMT, which has been proposed, for low voltage (LV, ≤5 V) RF operation. The proposed transistor shows excellent DC ( Idmax =1.9 A/mm, gmmax =0.66 S/mm) and RF small-signal characteristics ( fT/fmax =145/195 GHz). Continuous-wave (CW) load-pull measurements at 30 GHz yield Psat of 0.6 (1.3) W/mm at Vds of 3.5 (5) V, and peak power-added efficiency (PAE) of 43% (42%). To the best of the authors’ knowledge, the Psat values are the highest reported for LV GaN-on-Si HEMTs in 5G FR2, despite the use of conventional alloyed contacts and a gate length ( Lg ) of 120 nm. Furthermore, among published LV GaN-on-Si HEMTs, the proposed transistor achieves a desired combination of saturation velocity ( vsat ) and knee voltage ( Vknee ), which are critical factors for LV power amplification. The results reflect the promising potential of the proposed heterostructure to achieve high transmit power in 5G FR2 handsets.
- 8 July 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (2)
Variable range hopping-assisted parasitic channel leakage in AlN/GaN/AlGaN HEMTs on Si
This work investigates the off-state leakage characteristics of AlN/GaN/AlGaN high electron mobility transistors (HEMTs) on Si substrate with varying mesa depths and uncovers the existence of a parasitic channel associated with the AlGaN back barrier. Significant differences in off-state leakage up to three orders of magnitude were observed between devices fabricated using different mesa depths. The electrical properties of AlN/GaN/AlGaN HEMTs were measured, and it was found that there is a N-type parasitic channel in the unintentionally doped AlGaN back-barrier. Analysis of the isolation test structure, which retains this parasitic channel, reveals a buffer leakage of 12.8 mA/mm and a sheet resistance of 7739.1 Ω/sq, as a result of the parasitic channel. The depletion electric field strength of the parasitic channel is 3.2 × 105 V/cm. Temperature-dependent I–V curves obtained from the isolation area affirm that the primary leakage mechanism is two-dimensional variable range hopping along the sidewall. As the isolation distance extends from 3 to 5 μm, the slope of the fitting line decreases from −53.14 to −126.11 due to increased resistance.
- 8 July 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (2)
Variable range hopping-assisted parasitic channel leakage in AlN/GaN/AlGaN HEMTs on Si
This work investigates the off-state leakage characteristics of AlN/GaN/AlGaN high electron mobility transistors (HEMTs) on Si substrate with varying mesa depths and uncovers the existence of a parasitic channel associated with the AlGaN back barrier. Significant differences in off-state leakage up to three orders of magnitude were observed between devices fabricated using different mesa depths. The electrical properties of AlN/GaN/AlGaN HEMTs were measured, and it was found that there is a N-type parasitic channel in the unintentionally doped AlGaN back-barrier. Analysis of the isolation test structure, which retains this parasitic channel, reveals a buffer leakage of 12.8 mA/mm and a sheet resistance of 7739.1 Ω/sq, as a result of the parasitic channel. The depletion electric field strength of the parasitic channel is 3.2 × 105 V/cm. Temperature-dependent I–V curves obtained from the isolation area affirm that the primary leakage mechanism is two-dimensional variable range hopping along the sidewall. As the isolation distance extends from 3 to 5 μm, the slope of the fitting line decreases from −53.14 to −126.11 due to increased resistance.