Philip Cunningham
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Philip Cunningham has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
Rodman R. Linn
4 shared publicationsDaniel Keyser
University at Albany, State University of New York, USA
2 shared publicationsC. Edminster
1 shared publication- Carol Anne Clayson
Woods Hole Oceanographic Institution Woods Hole MA USA
1 shared publication Cathy J. Wilson
1 shared publication- Eunmo Koo
Los Alamos National Laboratory
1 shared publication
Latest Publications
- Open Access
- 1 August 2013
- Published by American Meteorological Society in Journal of Applied Meteorology and Climatology
- Vol. 52 (8) , 1716-1737
Large-Eddy Simulations of Air Flow and Turbulence within and around Low-Aspect-Ratio Cylindrical Open-Top Chambers
The flow around cylindrical open-top chambers (OTCs) with aspect ratios (i.e., height-to-diameter ratios) much less than unity is investigated using a large-eddy simulation (LES) model. The solid structures are represented using the immersed boundary method, and the ambient flow in which the OTCs are embedded is representative of a turbulent atmospheric boundary layer. Results from the LES model show that the flow inside OTCs depends strongly on the height of the chamber wall. In particular, as chamber height increases the flow impinging on the upstream wall is deflected more in the vertical direction, a stronger recirculation flow develops inside the chamber, turbulence intensities are greater, and there is stronger vertical transport and mixing within the OTC, even at or near the ground. For low wall heights (i.e., very low aspect ratios), however, the flow impinging on the OTC is only diverted weakly in the vertical direction; aside from a small recirculation zone inside the OTC near the upstream wall and a small region near the downstream wall as the flow separates from the ground, there is minimal vertical mixing and the turbulence intensities are small. The results of these simulations, while general in nature, are particularly relevant to design considerations for manipulative field experiments in highly heterogeneous, low-stature ecosystems such as Arctic shrubs and grasses.
- 1 August 2013
- Published by American Meteorological Society in Journal of Applied Meteorology and Climatology
- Vol. 52 (8) , 1716-1737
Open AccessLarge-Eddy Simulations of Air Flow and Turbulence within and around Low-Aspect-Ratio Cylindrical Open-Top Chambers
The flow around cylindrical open-top chambers (OTCs) with aspect ratios (i.e., height-to-diameter ratios) much less than unity is investigated using a large-eddy simulation (LES) model. The solid structures are represented using the immersed boundary method, and the ambient flow in which the OTCs are embedded is representative of a turbulent atmospheric boundary layer. Results from the LES model show that the flow inside OTCs depends strongly on the height of the chamber wall. In particular, as chamber height increases the flow impinging on the upstream wall is deflected more in the vertical direction, a stronger recirculation flow develops inside the chamber, turbulence intensities are greater, and there is stronger vertical transport and mixing within the OTC, even at or near the ground. For low wall heights (i.e., very low aspect ratios), however, the flow impinging on the OTC is only diverted weakly in the vertical direction; aside from a small recirculation zone inside the OTC near the upstream wall and a small region near the downstream wall as the flow separates from the ground, there is minimal vertical mixing and the turbulence intensities are small. The results of these simulations, while general in nature, are particularly relevant to design considerations for manipulative field experiments in highly heterogeneous, low-stature ecosystems such as Arctic shrubs and grasses.
- 1 May 2012
- Published by Elsevier in Agricultural and Forest Meteorology
- Vol. 157, 60-76
Using periodic line fires to gain a new perspective on multi-dimensional aspects of forward fire spread
- 1 May 2012
- Published by Elsevier in Agricultural and Forest Meteorology
- Vol. 157, 60-76
Using periodic line fires to gain a new perspective on multi-dimensional aspects of forward fire spread
- 26 June 2009
- Published by American Geophysical Union (AGU) in Geophysical Research Letters
- Vol. 36 (12)
Severe convective storms initiated by intense wildfires: Numerical simulations of pyro‐convection and pyro‐tornadogenesis
On the afternoon of 18 January 2003, wildfires swept through several outer suburbs of Canberra (Australia) producing, inter alia, a series of large pyro‐cumulonimbus cells and at least one tornado. The results of a large‐eddy simulation with a parameterized fire are reported here. The simulation, motivated by the Canberra wildfires and severe storms, captures the main characteristics of the observed pyro‐cumulonimbi, including the formation of a tornado close to where one was observed. In addition, the model develops prominent horizontally oriented vortices on the western side of the fire in the direction of the low‐level shear, and a series of horizontally oriented vortices on the upstream side of the convection column. The production of water by the fire is critical for the development of a pyro‐cumulonimbus cell intense enough to reach the tropopause as observed and plays a significant role in the associated tornadogenesis.
- 26 June 2009
- Published by American Geophysical Union (AGU) in Geophysical Research Letters
- Vol. 36 (12)
Severe convective storms initiated by intense wildfires: Numerical simulations of pyro‐convection and pyro‐tornadogenesis
On the afternoon of 18 January 2003, wildfires swept through several outer suburbs of Canberra (Australia) producing, inter alia, a series of large pyro‐cumulonimbus cells and at least one tornado. The results of a large‐eddy simulation with a parameterized fire are reported here. The simulation, motivated by the Canberra wildfires and severe storms, captures the main characteristics of the observed pyro‐cumulonimbi, including the formation of a tornado close to where one was observed. In addition, the model develops prominent horizontally oriented vortices on the western side of the fire in the direction of the low‐level shear, and a series of horizontally oriented vortices on the upstream side of the convection column. The production of water by the fire is critical for the development of a pyro‐cumulonimbus cell intense enough to reach the tropopause as observed and plays a significant role in the associated tornadogenesis.
- 1 August 2008
- Published by Elsevier in Dynamics of Atmospheres and Oceans
- Vol. 45 (3-4) , 165-186
Downwelling and upwelling regimes: Connections between surface fronts and abyssal circulation
- 1 August 2008
- Published by Elsevier in Dynamics of Atmospheres and Oceans
- Vol. 45 (3-4) , 165-186
Downwelling and upwelling regimes: Connections between surface fronts and abyssal circulation
- 1 August 2007
- Published by American Meteorological Society in Journal of Applied Meteorology and Climatology
- Vol. 46 (8) , 1214-1229
Vorticity-Based Detection of Tropical Cyclogenesis
Ocean wind vectors from the SeaWinds scatterometer aboard the Quick Scatterometer (QuikSCAT) satellite and Geostationary Operational Environmental Satellite (GOES) imagery are used to develop an objective technique that can detect and monitor tropical disturbances associated with the early stages of tropical cyclogenesis in the Atlantic basin. The technique is based on identification of surface vorticity and wind speed signatures that exceed certain threshold magnitudes, with vorticity averaged over an appropriate spatial scale. The threshold values applied herein are determined from the precursors of 15 tropical cyclones during the 1999–2004 Atlantic Ocean hurricane seasons using research-quality QuikSCAT data. The choice of these thresholds is complicated by the lack of suitable validation data. The combination of GOES and QuikSCAT data is used to track the tropical disturbances that are precursors to the 15 tropical cyclones. This combination of data can be used to test detection but is not as easily used to examine false alarms. Tropical disturbances are found for these cases within a range of 19–101 h before classification as tropical cyclones by the National Hurricane Center. The 15 cases are further subdivided based upon their origination source (i.e., easterly wave, upper-level cutoff low, stagnant frontal zone, etc.). The primary focus centers on the cases associated with tropical waves, because these waves account for the majority of all Atlantic tropical cyclones. The detection technique illustrates the ability to track these tropical disturbances from near the coast of Africa. Analysis of the pretropical cyclone (pre-TC) tracks for these cases depicts stages, related to wind speed and precipitation, in the evolution of a tropical disturbance within an easterly wave to a tropical cyclone.
- 1 August 2007
- Published by American Meteorological Society in Journal of Applied Meteorology and Climatology
- Vol. 46 (8) , 1214-1229
Vorticity-Based Detection of Tropical Cyclogenesis
Ocean wind vectors from the SeaWinds scatterometer aboard the Quick Scatterometer (QuikSCAT) satellite and Geostationary Operational Environmental Satellite (GOES) imagery are used to develop an objective technique that can detect and monitor tropical disturbances associated with the early stages of tropical cyclogenesis in the Atlantic basin. The technique is based on identification of surface vorticity and wind speed signatures that exceed certain threshold magnitudes, with vorticity averaged over an appropriate spatial scale. The threshold values applied herein are determined from the precursors of 15 tropical cyclones during the 1999–2004 Atlantic Ocean hurricane seasons using research-quality QuikSCAT data. The choice of these thresholds is complicated by the lack of suitable validation data. The combination of GOES and QuikSCAT data is used to track the tropical disturbances that are precursors to the 15 tropical cyclones. This combination of data can be used to test detection but is not as easily used to examine false alarms. Tropical disturbances are found for these cases within a range of 19–101 h before classification as tropical cyclones by the National Hurricane Center. The 15 cases are further subdivided based upon their origination source (i.e., easterly wave, upper-level cutoff low, stagnant frontal zone, etc.). The primary focus centers on the cases associated with tropical waves, because these waves account for the majority of all Atlantic tropical cyclones. The detection technique illustrates the ability to track these tropical disturbances from near the coast of Africa. Analysis of the pretropical cyclone (pre-TC) tracks for these cases depicts stages, related to wind speed and precipitation, in the evolution of a tropical disturbance within an easterly wave to a tropical cyclone.
- 1 June 2007
- Published by American Meteorological Society in Journal of the Atmospheric Sciences
- Vol. 64 (6) , 2105-2115
Idealized Numerical Simulations of the Interactions between Buoyant Plumes and Density Currents
Idealized numerical experiments using a large-eddy simulation (LES) model are performed to examine the fundamental dynamical processes associated with the interactions between buoyant plumes and density currents. The aim of these simulations is to provide insight into the rapid changes in the structure of plumes that may be observed during the passage of density current phenomena such as thunderstorm outflows, sea-breeze fronts, or intense cold fronts. The LES model results indicate that when the ambient winds are calm the vertical velocity in the plume decreases with the passage of the density current, but that when the ambient winds oppose the motion of the density current a significant increase in vertical velocity in the plume may occur temporarily. In the latter case, the pressure perturbation and the associated region of horizontal convergence that lead the head of the density current interact with the tilted plume, causing the base of the plume to become vertical and resulting in a dramatic increase in vertical velocity within the plume. This basic dynamical behavior occurs over a relatively broad range of parameters, provided the characteristic velocity in the density current (taken as the densimetric speed) exceeds the ambient wind speed. When this is the case, the interaction is dominated by the effect of the density current on the buoyant plume such that the plume is essentially advected as a passive tracer by the flow due to the density current, and the increase in vertical velocity depends on the inverse of the convective Froude number of the buoyant plume.
- 1 June 2007
- Published by American Meteorological Society in Journal of the Atmospheric Sciences
- Vol. 64 (6) , 2105-2115
Idealized Numerical Simulations of the Interactions between Buoyant Plumes and Density Currents
Idealized numerical experiments using a large-eddy simulation (LES) model are performed to examine the fundamental dynamical processes associated with the interactions between buoyant plumes and density currents. The aim of these simulations is to provide insight into the rapid changes in the structure of plumes that may be observed during the passage of density current phenomena such as thunderstorm outflows, sea-breeze fronts, or intense cold fronts. The LES model results indicate that when the ambient winds are calm the vertical velocity in the plume decreases with the passage of the density current, but that when the ambient winds oppose the motion of the density current a significant increase in vertical velocity in the plume may occur temporarily. In the latter case, the pressure perturbation and the associated region of horizontal convergence that lead the head of the density current interact with the tilted plume, causing the base of the plume to become vertical and resulting in a dramatic increase in vertical velocity within the plume. This basic dynamical behavior occurs over a relatively broad range of parameters, provided the characteristic velocity in the density current (taken as the densimetric speed) exceeds the ambient wind speed. When this is the case, the interaction is dominated by the effect of the density current on the buoyant plume such that the plume is essentially advected as a passive tracer by the flow due to the density current, and the increase in vertical velocity depends on the inverse of the convective Froude number of the buoyant plume.
- 14 March 2007
- Published by American Geophysical Union (AGU) in Journal of Geophysical Research: Atmospheres
- Vol. 112 (D5)
Numerical simulations of grass fires using a coupled atmosphere‐fire model: Dynamics of fire spread
Numerical simulations using a coupled atmosphere‐fire model (called HIGRAD/FIRETEC) are examined to investigate the dynamics of fire behavior in grasslands, focusing specifically on the relative roles and contributions of radiative and convective heat transfer and the relationships of these processes to the evolution of the solid fuel temperature; the three‐dimensional velocity fields in the vicinity of the fire; and the depletion of fuel, fuel moisture, and oxygen. The progression of the fire past a given point in these simulations is divided into a preheating period and an active burning period. The preheating period is characterized by a slowly increasing radiative heating of the fuel that evaporates fuel moisture and raises the temperature of the fuel slightly and by weak convective cooling because the gases flowing over the heated solid fuel are still cooler than the fuel itself. The active burning period is characterized by the presence of a strong pulse of convective heating and continued radiative heating, accompanied by the development of large vertical velocities and a rapid increase in fuel temperature that causes the reaction rates to increase and the fuel to begin to burn, producing heat and increasing the rates of depletion of fuel and oxygen. In all simulations, the magnitude of the convective heat transfer is greater than that of the radiative heat transfer; however, these processes and their relationships to the three‐dimensional structure and evolution of the fire are shown to depend both on the ambient wind speed and on the specific location along the fire front (e.g., at the head of the fire where the fire is spreading in the direction of the ambient wind, or on the flank of the fire where the fire is spreading in the direction almost perpendicular to the ambient wind).
- 14 March 2007
- Published by American Geophysical Union (AGU) in Journal of Geophysical Research: Atmospheres
- Vol. 112 (D5)
Numerical simulations of grass fires using a coupled atmosphere‐fire model: Dynamics of fire spread
Numerical simulations using a coupled atmosphere‐fire model (called HIGRAD/FIRETEC) are examined to investigate the dynamics of fire behavior in grasslands, focusing specifically on the relative roles and contributions of radiative and convective heat transfer and the relationships of these processes to the evolution of the solid fuel temperature; the three‐dimensional velocity fields in the vicinity of the fire; and the depletion of fuel, fuel moisture, and oxygen. The progression of the fire past a given point in these simulations is divided into a preheating period and an active burning period. The preheating period is characterized by a slowly increasing radiative heating of the fuel that evaporates fuel moisture and raises the temperature of the fuel slightly and by weak convective cooling because the gases flowing over the heated solid fuel are still cooler than the fuel itself. The active burning period is characterized by the presence of a strong pulse of convective heating and continued radiative heating, accompanied by the development of large vertical velocities and a rapid increase in fuel temperature that causes the reaction rates to increase and the fuel to begin to burn, producing heat and increasing the rates of depletion of fuel and oxygen. In all simulations, the magnitude of the convective heat transfer is greater than that of the radiative heat transfer; however, these processes and their relationships to the three‐dimensional structure and evolution of the fire are shown to depend both on the ambient wind speed and on the specific location along the fire front (e.g., at the head of the fire where the fire is spreading in the direction of the ambient wind, or on the flank of the fire where the fire is spreading in the direction almost perpendicular to the ambient wind).
- 15 November 2006
- Published by Elsevier in Forest Ecology and Management
- Vol. 234, S92
Dynamics of fire spread in grasslands: Numerical simulations with a physics-based fire model
- 15 November 2006
- Published by Elsevier in Forest Ecology and Management
- Vol. 234, S92
Dynamics of fire spread in grasslands: Numerical simulations with a physics-based fire model
- 6 July 2005
- Published by American Geophysical Union (AGU) in Journal of Geophysical Research: Atmospheres
- Vol. 110 (D13)
Numerical simulations of grass fires using a coupled atmosphere–fire model: Basic fire behavior and dependence on wind speed
Numerical simulations using a fire model, FIRETEC, coupled to an atmospheric dynamics model, HIGRAD, are examined to investigate several fundamental aspects of fire behavior in grasslands, and specifically the dependence of this behavior on the ambient atmospheric winds and on the initial length of the fire line. The FIRETEC model is based on a multi‐phase transport approach, and incorporates representations of the physical processes that govern wildfires, such as combustion and radiative and convective heat exchange. Results from the coupled model show that the forward spread of the simulated fires increases with increasing ambient wind speed, and the spread rates are consistent with those observed in field experiments of grass fires; however, the forward spread also depends significantly on the initial length of the fire line, and for a given ambient wind speed the spread rate for long (100 m) lines is greater than that for short (16 m) lines. The spread of the simulated fires in the lateral direction also depends on the ambient wind speed and the length of the fire line, and a possible explanation for this effect is given. For weak ambient winds, the shape of the fire perimeter is dramatically different from that seen with higher wind speeds. The shape of the fire perimeter is also shown to depend on the initial length of the fire line. These differences in fire behavior are attributed to the differences in the nature of the coupled atmosphere–fire interactions among these cases, and are described in terms of the complex interplay between radiative and convective heat transfer.
- 6 July 2005
- Published by American Geophysical Union (AGU) in Journal of Geophysical Research: Atmospheres
- Vol. 110 (D13)
Numerical simulations of grass fires using a coupled atmosphere–fire model: Basic fire behavior and dependence on wind speed
Numerical simulations using a fire model, FIRETEC, coupled to an atmospheric dynamics model, HIGRAD, are examined to investigate several fundamental aspects of fire behavior in grasslands, and specifically the dependence of this behavior on the ambient atmospheric winds and on the initial length of the fire line. The FIRETEC model is based on a multi‐phase transport approach, and incorporates representations of the physical processes that govern wildfires, such as combustion and radiative and convective heat exchange. Results from the coupled model show that the forward spread of the simulated fires increases with increasing ambient wind speed, and the spread rates are consistent with those observed in field experiments of grass fires; however, the forward spread also depends significantly on the initial length of the fire line, and for a given ambient wind speed the spread rate for long (100 m) lines is greater than that for short (16 m) lines. The spread of the simulated fires in the lateral direction also depends on the ambient wind speed and the length of the fire line, and a possible explanation for this effect is given. For weak ambient winds, the shape of the fire perimeter is dramatically different from that seen with higher wind speeds. The shape of the fire perimeter is also shown to depend on the initial length of the fire line. These differences in fire behavior are attributed to the differences in the nature of the coupled atmosphere–fire interactions among these cases, and are described in terms of the complex interplay between radiative and convective heat transfer.
- 7 March 2005
- Published by CSIRO Publishing in International Journal of Wildland Fire
- Vol. 14 (1) , 61-75
Coherent vortical structures in numerical simulations of buoyant plumes from wildland fires
The structure and dynamics of buoyant plumes arising from surface-based heat sources in a vertically sheared ambient atmospheric flow are examined via simulations of a three-dimensional, compressible numerical model. Simple circular heat sources and asymmetric elliptical ring heat sources that are representative of wildland fires of moderate intensity are considered. Several different coherent vortical structures that dominate the plume structure and evolution are evident in the simulations, and these structures correspond well with those observed in plumes from wildland fires. For the circular source, these structures include: (i) a counter-rotating vortex pair aligned with the plume trajectory that is associated with a bifurcation of the plume, (ii) transverse shear-layer vortices on the upstream face of the plume, and (iii) vertically oriented wake vortices that form periodically with alternating sign on either side of the downstream edge of the plume base. For the elliptical ring source, a streamwise counter-rotating vortex pair is apparent on each flank, and a transverse horizontal vortex is observed above the head of the source. In all simulations the plume cross section is represented poorly by a self-similar Gaussian distribution.
- 7 March 2005
- Published by CSIRO Publishing in International Journal of Wildland Fire
- Vol. 14 (1) , 61-75
Coherent vortical structures in numerical simulations of buoyant plumes from wildland fires
The structure and dynamics of buoyant plumes arising from surface-based heat sources in a vertically sheared ambient atmospheric flow are examined via simulations of a three-dimensional, compressible numerical model. Simple circular heat sources and asymmetric elliptical ring heat sources that are representative of wildland fires of moderate intensity are considered. Several different coherent vortical structures that dominate the plume structure and evolution are evident in the simulations, and these structures correspond well with those observed in plumes from wildland fires. For the circular source, these structures include: (i) a counter-rotating vortex pair aligned with the plume trajectory that is associated with a bifurcation of the plume, (ii) transverse shear-layer vortices on the upstream face of the plume, and (iii) vertically oriented wake vortices that form periodically with alternating sign on either side of the downstream edge of the plume base. For the elliptical ring source, a streamwise counter-rotating vortex pair is apparent on each flank, and a transverse horizontal vortex is observed above the head of the source. In all simulations the plume cross section is represented poorly by a self-similar Gaussian distribution.