Ruud A. W. M. Henkes
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ruud A. W. M. Henkes has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Benjamin Sanderse
Centrum Wiskunde & Informatica Science Park 123 Amsterdam The Netherlands
3 shared publications - Cornelis Vuik
Delft Institute of Applied Mathematics, Delft University of Technology, 2628 CD Delft, The Netherlands
2 shared publications Haoyu Li
Faculty of Mechanical Engineering, Delft University of Technology , Delft 2628 CD, The Netherlands
2 shared publications- Jurriaan F. H. Buist
Scientific Computing Group Centrum Wiskunde & Informatica (CWI) Amsterdam The Netherlands
2 shared publications L. M. Portela
Department of Chemical Engineering, Delft University of Technology, Post Office Box 5, 2600 AA Delft, The Netherlands
2 shared publicationsA. Segal
1 shared publication
Latest Publications
- 30 September 2024
- Published by ASME International in Journal of Fluids Engineering
- Vol. 147 (2) , 1-38
Simulation of Interfacial Waves in Core-Annular Pipe Flow With a Turbulent Annulus
Numerical simulations are conducted for the wave initiation, growth, and saturation at the oil–water interface in core-annular flow (CAF). The focus is on conditions with a turbulent water annulus, but the laminar water annulus is also considered. The simulation results are compared with lab measurements. The growth rate for the linear instability of different wavelengths in the case of a turbulent water annulus is obtained from two-dimensional (2D) axisymmetric Reynolds-averaged Navier–Stokes (RANS) simulations with the Launder–Sharma low-Reynolds number k–ε model. The latter simulation results provide the most unstable wavelength for the turbulent water annulus. Our study also shows the following. The maximum wave growth rate for a turbulent water annulus is significantly higher than for a laminar water annulus. The most unstable wavelength in the simulations is about 25% smaller than in the experiments. The wave amplitude for the different wavelengths in the simulations is typically 17% lower than in the experiments.
- 30 September 2024
- Published by ASME International in Journal of Fluids Engineering
- Vol. 147 (2) , 1-38
Simulation of Interfacial Waves in Core-Annular Pipe Flow With a Turbulent Annulus
Numerical simulations are conducted for the wave initiation, growth, and saturation at the oil–water interface in core-annular flow (CAF). The focus is on conditions with a turbulent water annulus, but the laminar water annulus is also considered. The simulation results are compared with lab measurements. The growth rate for the linear instability of different wavelengths in the case of a turbulent water annulus is obtained from two-dimensional (2D) axisymmetric Reynolds-averaged Navier–Stokes (RANS) simulations with the Launder–Sharma low-Reynolds number k–ε model. The latter simulation results provide the most unstable wavelength for the turbulent water annulus. Our study also shows the following. The maximum wave growth rate for a turbulent water annulus is significantly higher than for a laminar water annulus. The most unstable wavelength in the simulations is about 25% smaller than in the experiments. The wave amplitude for the different wavelengths in the simulations is typically 17% lower than in the experiments.
- Open Access
Entropy-Stable Model Reduction of One-Dimensional Hyperbolic Systems using Rational Quadratic Manifolds
In this work we propose a novel method to ensure important entropy inequalities are satisfied semi-discretely when constructing reduced order models (ROMs) on nonlinear reduced manifolds. We are in particular interested in ROMs of systems of nonlinear hyperbolic conservation laws. The so-called entropy stability property endows the semi-discrete ROMs with physically admissible behaviour. The method generalizes earlier results on entropy-stable ROMs constructed on linear spaces. The ROM works by evaluating the projected system on a well-chosen approximation of the state that ensures entropy stability. To ensure accuracy of the ROM after this approximation we locally enrich the tangent space of the reduced manifold with important quantities. Using numerical experiments on some well-known equations (the inviscid Burgers equation, shallow water equations and compressible Euler equations) we show the improved structure-preserving properties of our ROM compared to standard approaches and that our approximations have minimal impact on the accuracy of the ROM. We additionally generalize the recently proposed polynomial reduced manifolds to rational polynomial manifolds and show that this leads to an increase in accuracy for our experiments.
Open AccessEntropy-Stable Model Reduction of One-Dimensional Hyperbolic Systems using Rational Quadratic Manifolds
In this work we propose a novel method to ensure important entropy inequalities are satisfied semi-discretely when constructing reduced order models (ROMs) on nonlinear reduced manifolds. We are in particular interested in ROMs of systems of nonlinear hyperbolic conservation laws. The so-called entropy stability property endows the semi-discrete ROMs with physically admissible behaviour. The method generalizes earlier results on entropy-stable ROMs constructed on linear spaces. The ROM works by evaluating the projected system on a well-chosen approximation of the state that ensures entropy stability. To ensure accuracy of the ROM after this approximation we locally enrich the tangent space of the reduced manifold with important quantities. Using numerical experiments on some well-known equations (the inviscid Burgers equation, shallow water equations and compressible Euler equations) we show the improved structure-preserving properties of our ROM compared to standard approaches and that our approximations have minimal impact on the accuracy of the ROM. We additionally generalize the recently proposed polynomial reduced manifolds to rational polynomial manifolds and show that this leads to an increase in accuracy for our experiments.
- Open Access
- 7 February 2024
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 174
Energy-stable discretization of the one-dimensional two-fluid model
- 7 February 2024
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 174
Open AccessEnergy-stable discretization of the one-dimensional two-fluid model
- Open Access
- 29 January 2024
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 174
DNS and RANS for core-annular flow with a turbulent annulus
- 29 January 2024
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 174
Open AccessDNS and RANS for core-annular flow with a turbulent annulus
- Open Access
- 24 January 2023
- Published by Wiley in International Journal for Numerical Methods in Fluids
- Vol. 95 (5) , 869-898
Energy‐consistent formulation of the pressure‐free two‐fluid model
The pressure‐free two‐fluid model (PFTFM) is a recent reformulation of the one‐dimensional two‐fluid model (TFM) for stratified incompressible flow in ducts (including pipes and channels), in which the pressure is eliminated through intricate use of the volume constraint. The disadvantage of the PFTFM was that the volumetric flow rate had to be specified as an input, even though it is an unknown quantity in case of periodic boundary conditions. In this work, we derive an expression for the volumetric flow rate that is based on the demand for energy (and momentum) conservation. This leads to PFTFM solutions that match those of the TFM, justifying the validity and necessity of the derived choice of volumetric flow rate. Furthermore, we extend an energy‐conserving spatial discretization of the TFM, in the form of a finite volume scheme, to the PFTFM. We propose a discretization of the volumetric flow rate that yields discrete momentum and energy conservation. The discretization is extended with an energy‐conserving discretization of the source terms related to gravity acting in the streamwise direction. Our numerical experiments confirm that the discrete energy is conserved for different problem settings, including sloshing in an inclined closed tank, and a traveling wave in a periodic domain. The PFTFM solutions and the volumetric flow rates match the TFM solutions, with reduced computation time, and with exact momentum and energy conservation.
- 24 January 2023
- Published by Wiley in International Journal for Numerical Methods in Fluids
- Vol. 95 (5) , 869-898
Open AccessEnergy‐consistent formulation of the pressure‐free two‐fluid model
The pressure‐free two‐fluid model (PFTFM) is a recent reformulation of the one‐dimensional two‐fluid model (TFM) for stratified incompressible flow in ducts (including pipes and channels), in which the pressure is eliminated through intricate use of the volume constraint. The disadvantage of the PFTFM was that the volumetric flow rate had to be specified as an input, even though it is an unknown quantity in case of periodic boundary conditions. In this work, we derive an expression for the volumetric flow rate that is based on the demand for energy (and momentum) conservation. This leads to PFTFM solutions that match those of the TFM, justifying the validity and necessity of the derived choice of volumetric flow rate. Furthermore, we extend an energy‐conserving spatial discretization of the TFM, in the form of a finite volume scheme, to the PFTFM. We propose a discretization of the volumetric flow rate that yields discrete momentum and energy conservation. The discretization is extended with an energy‐conserving discretization of the source terms related to gravity acting in the streamwise direction. Our numerical experiments confirm that the discrete energy is conserved for different problem settings, including sloshing in an inclined closed tank, and a traveling wave in a periodic domain. The PFTFM solutions and the volumetric flow rates match the TFM solutions, with reduced computation time, and with exact momentum and energy conservation.
- 16 November 2018
- Published by ASME International in Journal of Fluids Engineering
- Vol. 141 (5)
Comparison of Computational Fluid Dynamics Simulations and Experiments for Stratified Air-Water Flows in Pipes
Stratified gas–liquid flow is a flow regime typically encountered in multiphase pipelines. The understanding and modeling of this regime is of engineering importance especially for the oil and gas industry. In this work, simulations have been conducted for stratified air–water flow in pipes. We solved the Reynolds-averaged Navier–Stokes (RANS) equations with the volume of fluid (VOF) method. The aim of this work was to evaluate the performance of the k–ω shear stress transport (SST) turbulence model with and without damping of the turbulence at the gas–liquid interface. Simulation results were compared with some of the latest experimental results found in the literature. A comparison between the simulated velocity and kinetic energy profiles and the experimental results obtained with the particle image velocimetry (PIV) technique was conducted. The characteristics of the interfacial waves were also extracted and compared with the experiments. It is shown that a proper damping of the turbulence close to the interface is needed to obtain agreement with the experimental pressure drop and liquid hold-up. In its current form, however, RANS with the k–ω turbulence model is still not able to give an accurate prediction of the velocity profiles and of the interface waves.
- 16 November 2018
- Published by ASME International in Journal of Fluids Engineering
- Vol. 141 (5)
Comparison of Computational Fluid Dynamics Simulations and Experiments for Stratified Air-Water Flows in Pipes
Stratified gas–liquid flow is a flow regime typically encountered in multiphase pipelines. The understanding and modeling of this regime is of engineering importance especially for the oil and gas industry. In this work, simulations have been conducted for stratified air–water flow in pipes. We solved the Reynolds-averaged Navier–Stokes (RANS) equations with the volume of fluid (VOF) method. The aim of this work was to evaluate the performance of the k–ω shear stress transport (SST) turbulence model with and without damping of the turbulence at the gas–liquid interface. Simulation results were compared with some of the latest experimental results found in the literature. A comparison between the simulated velocity and kinetic energy profiles and the experimental results obtained with the particle image velocimetry (PIV) technique was conducted. The characteristics of the interfacial waves were also extracted and compared with the experiments. It is shown that a proper damping of the turbulence close to the interface is needed to obtain agreement with the experimental pressure drop and liquid hold-up. In its current form, however, RANS with the k–ω turbulence model is still not able to give an accurate prediction of the velocity profiles and of the interface waves.
- 25 October 2018
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 857, 539-561
Formation and break-up of rigid agglomerates in turbulent channel and pipe flows
We have developed and applied an Eulerian–Lagrangian model for the transport, formation, break-up, deposition and re-entrainment of particle agglomerates. In this paper, we focus on agglomeration and break-up. Simulations were carried out to investigate what changes in the turbulent flow are inflicted by the presence of the agglomerates. Also, the dependence of the properties of the agglomerates on the Reynolds number of the flow and on the strength of the bonds between the primary particles is studied. The presence of the agglomerates attenuates the turbulence and thereby lowers the Reynolds stresses. As a result, the flow rate increases at constant pressure drop when agglomerates are formed (up to a certain dimension). If the agglomerates surpass this dimension, long-distance viscosity effects become dominant and a flow rate decrease occurs. The characteristics of the agglomerates are largely insensitive to the Reynolds number, provided the flow is turbulent. The agglomerates have an open and porous structure, and a fractal dimension of 1.8–2.3. Their mean mass scales exponentially with the strength of the internal bonds. Contrary to assumptions that are typically made in engineering models in the literature, agglomerates do not preferentially break into two fragments of similar size.
- 25 October 2018
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 857, 539-561
Formation and break-up of rigid agglomerates in turbulent channel and pipe flows
We have developed and applied an Eulerian–Lagrangian model for the transport, formation, break-up, deposition and re-entrainment of particle agglomerates. In this paper, we focus on agglomeration and break-up. Simulations were carried out to investigate what changes in the turbulent flow are inflicted by the presence of the agglomerates. Also, the dependence of the properties of the agglomerates on the Reynolds number of the flow and on the strength of the bonds between the primary particles is studied. The presence of the agglomerates attenuates the turbulence and thereby lowers the Reynolds stresses. As a result, the flow rate increases at constant pressure drop when agglomerates are formed (up to a certain dimension). If the agglomerates surpass this dimension, long-distance viscosity effects become dominant and a flow rate decrease occurs. The characteristics of the agglomerates are largely insensitive to the Reynolds number, provided the flow is turbulent. The agglomerates have an open and porous structure, and a fractal dimension of 1.8–2.3. Their mean mass scales exponentially with the strength of the internal bonds. Contrary to assumptions that are typically made in engineering models in the literature, agglomerates do not preferentially break into two fragments of similar size.
- Open Access
- 1 October 2017
- Published by Elsevier in Computers & Fluids
- Vol. 156, 34-47
Efficient simulation of one-dimensional two-phase flow with a high-order h-adaptive space-time Discontinuous Galerkin method
- 1 October 2017
- Published by Elsevier in Computers & Fluids
- Vol. 156, 34-47
Open AccessEfficient simulation of one-dimensional two-phase flow with a high-order h-adaptive space-time Discontinuous Galerkin method
- 1 November 2016
- Published by Elsevier in Journal of Computational Physics
- Vol. 325, 314-337
A fully conservative mimetic discretization of the Navier–Stokes equations in cylindrical coordinates with associated singularity treatment
- 1 November 2016
- Published by Elsevier in Journal of Computational Physics
- Vol. 325, 314-337
A fully conservative mimetic discretization of the Navier–Stokes equations in cylindrical coordinates with associated singularity treatment
- Open Access
- 1 June 2014
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 62, 161-173
PIV measurements of waves and turbulence in stratified horizontal two-phase pipe flow
- 1 June 2014
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 62, 161-173
Open AccessPIV measurements of waves and turbulence in stratified horizontal two-phase pipe flow