GBGunnar Bergman

Gunnar Bergman

*This is an algorithmically generated author record based on publicly available information.

Gunnar Bergman has a total of 27 co-authors. Here are the top co-authors by number of shared publications:

  • Mikael Stefan Hedenqvist

    School of Engineering Sciences in Chemistry, Biotechnology and Health, Fibre and Polymer Technology, KTH Royal Institute of Technology, Stockholm, Sweden

    10 shared publications
  • J. E. Ritums

    School of Chemical Science and Engineering, Fiber and Polymer Technology, Royal Institute of Technology, SE‐100 44 Stockholm, Sweden

    4 shared publications
  • S. Römhild

    SWEREA KIMAB, Drottning Kristinas väg 48, SE-114 28 Stockholm, Sweden

    4 shared publications
  • U. W. Gedde

    School of Chemical Science and Engineering, Fibre and Polymer Technology, Royal Institute of Technology , Stockholm, Sweden

    3 shared publications
  • M. Condé‐Brana

    Department of Fiber and Polymer Technology, Royal Institute of Technology, S-100 44 Stockholm, Sweden

    2 shared publications
  • Young J. Shur

    Department of Polymer Technology, The Royal Institute of Technology, S‐100 44 Stockholm, Sweden

    2 shared publications

Latest Publications

  • Failure analysis of a leaching reactor made of glass-fiber reinforced plastic

    by Mari Lindgren, Gunnar Bergman, Markus Kakkonen, Markus Lehtonen, Jarno Jokinen, Markus Wallin, Olli Saarela, Jyrki Vuorinen


  • The effect of water activity on the sorption and diffusion of water in thermosets based on polyester, vinyl ester, and novolac resins

    by S. Römhild, M.S. Hedenqvist, G. Bergman

    In this work, the transport properties of water in various thermoset resins typically used for fiber‐reinforced plastic process equipment (vinyl ester, novolac, bisphenol‐A‐epoxy‐based polyester, and urethane‐modified vinyl ester) were systematically studied with a focus on the effects of water activity. Sorption and desorption studies were carried out in aqueous solutions (water activity = 0.78–1) with different salts (NaCl, MgCl2, Na2SO4, and KCl) and one nonionic substance (sucrose) within the temperature interval 65–95°C. It was found that the water concentration in thermoset resins with different chemical structures could be predicted from the water activity, regardless of the actual solute (salt or sucrose) in the aqueous solution. The water quasi‐equilibrium concentration decreased with decreasing water activity, whereas the average diffusion coefficient was considered to be independent of water activity in the studied water activity range. A relationship, based on a power law fit, was established describing the water concentration as a function of the water activity and the concentration of pure water. The relationship was independent of resin chemistry and temperature. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers


  • Influence of Disclination Density and Crystallinity on the Transport Properties of a Liquid Crystalline Copolyester

    by S. Römhild, H. Yousefi, G. Bergman, U. W. Gedde, M. S. Hedenqvist

    The effect of annealing on the structure and transport properties of a compression‐molded liquid crystalline co‐polyester (Vectra® A950) consisting of 73mol% poly(hydroxybenzoic acid) and 27mol% poly(hydroxy‐naphthoic acid) was studied. Films were annealed above (310°C) or below (260°C) the melting point. The structure was studied with density measurements, optical microscopy, differential scanning calorimetry and wide‐angle X‐ray diffraction. It was observed that the density increased as a linear function of the logarithm of annealing time and that the crystallinity increased only on annealing below the crystal melting point. The increase in density above the melting point, and also to a large extent below the melting point, must have occurred through improved molecular packing but without any reduction in disclination density, as revealed by optical microscopy. The methanol diffusivity, obtained from desorption data, showed a moderate decrease with increasing density; the trend was only significant within a 60% confidence limit.


  • Assessing the transport properties of organic penetrants in low‐density polyethylene using free volume models

    by J. E. Ritums, B. Neway, F. Doghieri, G. Bergman, U. W. Gedde, M. S. Hedenqvist

    Three models, two of them relying on free volume—the Cohen–Turnbull–Fujita (CTF) model and the Vrentas–Duda (VD) model, and the third being empirical using an exponential concentration dependence of the diffusivity, were applied to desorption data for a series of alkane penetrants (2,2‐dimethylbutane, cyclohexane, n‐hexane, n‐decane, and n‐tetradecane) in low‐density polyethylene. The CTF model described the desorption data very well and better than the exponential diffusion law. The VD model with the attractive feature of being based on independently determined parameters was unsuccessful in describing the desorption data. Diffusivity data indicated that the three components outside the crystal core were less accessible to n‐tetradecane than to the other penetrants. This indication was further substantiated by solubility data. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 723–734, 2007


  • Mechanical properties of high‐density polyethylene and crosslinked high‐density polyethylene in crude oil and its components

    by J. E. Ritums, A. Mattozzi, U. W. Gedde, M. S. Hedenqvist, G. Bergman, M. Palmlöf

    The tensile and stress‐relaxation properties of an uncrosslinked and a loosely silane‐crosslinked high‐density polyethylene exposed to organic “crude‐oil” penetrants were assessed. The measurements were performed on penetrant‐saturated samples, surrounded by the organic liquid throughout the experiment. The penetrant solubilities in the two polymers were similar and in accordance with predicted values based on the solubility parameter method. The stiffness and strength of the swollen samples were significantly less than those of the dry samples, indicating a plasticization of the amorphous component. Raman spectroscopy on polyethylene exposed to deuterated n‐hexane revealed a penetrant‐induced partial melting/dissolution of the crystal surface and an intact crystal core component. The stress‐relaxation rates, within the time frame of the experiment (∼1 s to 18 h), were approximately the same, independent of silane‐crosslinks and the presence of penetrants. This indicated that the mechanical α‐relaxation, which is the main relaxation process occurring in the measured time interval, was not affected by the penetrants. Consequently, its rate seemed to be independent of the crystal surface dissolution (decrease in the content of crystal‐core interface). The shape of the “log stress–log time” curves of the swollen samples was, however, different from that of the dry samples. This was most likely attributed to a time‐dependent saturation of penetrant to a higher level associated with the stretched state of the polymer sample. The silane crosslinks affected only the elongation at break, which was less than that of the uncrosslinked material. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 641–648, 2006


  • Adhesion of microwave‐plasma‐treated fluoropolymers to thermoset vinylester

    by M. S. Hedenqvist, A. Merveille, K. Odelius, A.‐C. Albertsson, G. Bergman


  • Sorption behavior in polymers above Tg: Relations between mechanical properties and swelling in limonene

    by J.E. Ritums, M.S. Hedenqvist, G. Bergman, T. Prodan, I. Emri

    The sorption behavior of two highly swelling “rubbery” polymers, natural rubber and polyethylene, has been studied. The polymers are in many aspects very different. Yet, when the solute mass uptake, in this case limonene, is plotted as a function of the square root of time, both polymers show similar “sigmoidal”‐types of curves. This triggered the research to determine what mechanisms were responsible for the observed similarities and if the degree in sigmoidal behavior and swelling anisotropy could be easily assessed explicitly by any mechanical parameter. It was found that their degrees of swelling anisotropy, described by a solute‐surface‐concentration relaxation time, could be explained by their relative bulk moduli. It was assumed that the ratio in bulk modulus at zero pressure, determined from compression measurements, could represent the ratio in expansion bulk modulus during swelling. However, the prediction in swelling anisotropy during sorption using the ratio in bulk modulus was slightly less successful when the swelling anisotropy was quantified as the relative ratio of sheet thickness to cross‐sectional area side length. It should be noted that the ratio in uniaxial tensile modulus between polyethylene and natural rubber was several orders of magnitude higher than their ratio in swelling anisotropy. The natural rubber sheet became saddle‐shaped during limonene sorption and collapsed into a flat shape when the saturation concentration was approached. During desorption, the sheet went from flat to cup‐shaped and then flat again at the end of desorption. The saddle and cup shapes occurred in both square and round sheets. These shapes are believed to be a consequence of buckling and deformation due to instabilities in the stress state of the sheet. This was, in turn, explained by the normally existing local variation in cross‐link density. POLYM. ENG. SCI., 45:1194–1202, 2005. © 2005 Society of Plastics Engineers


  • Structure and properties of poly(ethylene‐co‐chlorotrifluoroethylene) and polyvinylidene fluoride exposed to water, hydrochloric acid, hydrobromic acid and tetrachloroethylene

    by M. S. Hedenqvist, J. E. Ritums, M. Condé‐Brana, G. Bergman

    The transport of water, hydrochloric acid, hydrobromic acid and tetrachloroethylene in an poly(ethylene‐co‐chlorotrifluoroethylene) and polyvinylidene fluoride were studied at 70°C by the sorption/desorption technique. The effects on the structure and mechanical properties were studied using size‐exclusion chromatography, infrared spectroscopy, differential scanning calorimetry and tensile testing. Solute concentrations in the polymers indicated that both the water and HCl/HBr components diffused into the polymers on exposure to acid solutions. The calculated water contents of the diffusing acids generally differed from the water content in the solution. The ratio of water content in the diffusing acid to that in the surrounding acid solution was generally a function of the relative vapor activity of water and HCl/HBr. It was possible to describe the 35%HCl and 47%HBr desorption data using a two component model. It was here assumed that the water and HCl/HBr diffused separately, each having its own constant diffusion coefficient. The water diffusivity was obtained from the pure water system, and this allowed the HCl/HBr diffusivity to be calculated. It was found that the diffusivity decreased, in a non‐simple way, as a function of solute size. The exposure to solute did not lower the molar mass of the polyvinylidene fluoride. Differential scanning calorimetry indicated the development of low‐melting point polyvinylidene fluoride crystals during the exposure to all solutes. This seemed to be a consequence of the long‐term exposure (175 to 376 days) at 70°C. The long‐term exposure stiffened several of the polyvinylidene fluoride resins and occasionally made them less ductile. The poly(ethylene‐co‐chlorotrifluoroethylene) also became stiffer, but it was otherwise unaffected as far as observation by the other available techniques was concerned.