Derek R. Oliver
Derek R. Oliver has a total of 50 co-authors. Here are the top co-authors by number of shared publications:
- Douglas J. Thomson
Department of Electrical and Computer Engineering, University of Manitoba, Winnipeg, MB R3T 5V6, Canada
11 shared publications - Michael S. Freund
Dalhousie University
7 shared publications G. E. Bridges
Department of Electrical and Computer Engineering, The University of Manitoba, Winnipeg, MB, Canada
6 shared publications- Behzad Kordi
Department of Electrical and Computer Engineering, University of Manitoba, Winnipeg, MB, Canada
4 shared publications - Jared Patterson Bruce
Department of Interface Science, Fritz-Haber Institute of the Max-Planck Society, 14195 Berlin, Germany
4 shared publications T. Tran
IDERS Inc., Winnipeg, Man., Canada
4 shared publications
Latest Publications
- 8 March 2022
- Published by Springer Nature in Neural Computing and Applications
- Vol. 34 (14) , 11739-11750
An interpretable CNN model for classification of partial discharge waveforms in 3D-printed dielectric samples with different void sizes
- 8 March 2022
- Published by Springer Nature in Neural Computing and Applications
- Vol. 34 (14) , 11739-11750
An interpretable CNN model for classification of partial discharge waveforms in 3D-printed dielectric samples with different void sizes
- Open Access
- 1 September 2017
- Published by Institution of Engineering and Technology (IET) in High Voltage
- Vol. 2 (3) , 200-204
Sensitivity analysis of a parallel‐plate method for measuring the dielectric permittivity of high‐voltage insulating materials
Ascertaining the dielectric character of polymeric insulation materials is of particular interest for comparative studies that use accelerated ageing and samples from decommissioned installations. In the case of polymeric samples, the possibility of physical deformation within the sample holder adds additional variability to comparative measurements. Using readily obtainable instrumentation, this study undertakes a systematic sensitivity analysis of a parallel‐plate capacitance measurement approach for polymeric materials that only has one capacitance plate in contact with the sample, avoiding issues of sample deformation. The analysis demonstrates that the biggest contributor of uncertainty in the measurement of the relative permittivity and loss tangent is the precision with which the plate–plate and plate–sample separation is determined. The measurements show that the determination of loss tangent can be susceptible to uncertainties arising from electrical noise, but that these can be controlled further by utilising more refined instrumentation.
- 1 September 2017
- Published by Institution of Engineering and Technology (IET) in High Voltage
- Vol. 2 (3) , 200-204
Open AccessSensitivity analysis of a parallel‐plate method for measuring the dielectric permittivity of high‐voltage insulating materials
Ascertaining the dielectric character of polymeric insulation materials is of particular interest for comparative studies that use accelerated ageing and samples from decommissioned installations. In the case of polymeric samples, the possibility of physical deformation within the sample holder adds additional variability to comparative measurements. Using readily obtainable instrumentation, this study undertakes a systematic sensitivity analysis of a parallel‐plate capacitance measurement approach for polymeric materials that only has one capacitance plate in contact with the sample, avoiding issues of sample deformation. The analysis demonstrates that the biggest contributor of uncertainty in the measurement of the relative permittivity and loss tangent is the precision with which the plate–plate and plate–sample separation is determined. The measurements show that the determination of loss tangent can be susceptible to uncertainties arising from electrical noise, but that these can be controlled further by utilising more refined instrumentation.
- 14 November 2016
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 6 (111) , 110344-110348
Direct contact four-point probe characterization of Si microwire absorbers for artificial photosynthesis
We present a facile approach that achieves four-point electrical characterization of silicon microwires fabricated using a bottom-up vapour–liquid–solid process.
- 14 November 2016
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 6 (111) , 110344-110348
Direct contact four-point probe characterization of Si microwire absorbers for artificial photosynthesis
We present a facile approach that achieves four-point electrical characterization of silicon microwires fabricated using a bottom-up vapour–liquid–solid process.
- 7 September 2016
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 6 (91) , 88239-88243
Monohydride signature as a key predictor of successful Si(110) surface functionalization
Methyl-terminated (110)-oriented silicon surfaces have been prepared from monohydride-terminated, H–Si(110) surfaces using a chlorination/alkylation procedure. Transmission infrared spectroscopy of the H–Si(110) surfaces showed absorption features indicating monohydride structures along the [−110] direction. X-ray photoelectron spectroscopy was used to characterize the methyl-terminated, CH3–Si(110), surfaces. Surface coverage calculations revealed 0.83 of an equivalent monolayer coverage for methyl-terminated Si(110) surfaces. No oxidation of silicon was observed in the high-resolution Si 2p spectra and the samples were stable against oxidation over time, with only 0.2 of a monolayer of surface oxide observed a month after the sample preparation. Thus, the chlorination/alkylation procedure can be used for the functionalization of monohydride Si(110) surfaces with improved long term stability.
- 7 September 2016
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 6 (91) , 88239-88243
Monohydride signature as a key predictor of successful Si(110) surface functionalization
Methyl-terminated (110)-oriented silicon surfaces have been prepared from monohydride-terminated, H–Si(110) surfaces using a chlorination/alkylation procedure. Transmission infrared spectroscopy of the H–Si(110) surfaces showed absorption features indicating monohydride structures along the [−110] direction. X-ray photoelectron spectroscopy was used to characterize the methyl-terminated, CH3–Si(110), surfaces. Surface coverage calculations revealed 0.83 of an equivalent monolayer coverage for methyl-terminated Si(110) surfaces. No oxidation of silicon was observed in the high-resolution Si 2p spectra and the samples were stable against oxidation over time, with only 0.2 of a monolayer of surface oxide observed a month after the sample preparation. Thus, the chlorination/alkylation procedure can be used for the functionalization of monohydride Si(110) surfaces with improved long term stability.
- 25 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 468-471
Correlation of microscopic textural features and degree of polymerization for thermally deteriorated cellulose insulation
This paper presents experimental results obtained from texture analysis of microscopy measurements performed on cellulose paper samples which have been thermally deteriorated to different levels. Samples were prepared in vials containing a small sample of Kraft paper tape along with insulating oil that were thermally stressed in an oven at 140 °C for durations of 0, 120, 250, and 400 hours. Analysis of changes in texture as a consequence of thermal deterioration is presented with a quantitative analysis developed by converting each microscopy image to a spatial grey-level dependence matrix (SGLDM) representative of the overall image texture and extracting statistical features from the SGLDM. These statistical features are correlated with degree of polymerization measurements to observe how aspects of the paper texture may change in relation to the tensile strength for different levels of thermal deterioration.
- 25 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 468-471
Correlation of microscopic textural features and degree of polymerization for thermally deteriorated cellulose insulation
This paper presents experimental results obtained from texture analysis of microscopy measurements performed on cellulose paper samples which have been thermally deteriorated to different levels. Samples were prepared in vials containing a small sample of Kraft paper tape along with insulating oil that were thermally stressed in an oven at 140 °C for durations of 0, 120, 250, and 400 hours. Analysis of changes in texture as a consequence of thermal deterioration is presented with a quantitative analysis developed by converting each microscopy image to a spatial grey-level dependence matrix (SGLDM) representative of the overall image texture and extracting statistical features from the SGLDM. These statistical features are correlated with degree of polymerization measurements to observe how aspects of the paper texture may change in relation to the tensile strength for different levels of thermal deterioration.
- 1 April 2016
- Published by Elsevier in Electric Power Systems Research
- Vol. 133, 104-112
Classification of degradation in oil-impregnated cellulose insulation using texture analysis of optical microscopy images
- 1 April 2016
- Published by Elsevier in Electric Power Systems Research
- Vol. 133, 104-112
Classification of degradation in oil-impregnated cellulose insulation using texture analysis of optical microscopy images
- 3 December 2015
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 7 (49) , 27160-27166
Electrical Characteristics of the Junction between PEDOT:PSS and Thiophene-Functionalized Silicon Microwires
Thiophene moieties have been attached to Si microwires (Si MWs) by a two–step chlorination/alkylation reaction method. X-ray photoelectron spectroscopy indicated that saturation of the surface occurred after 30 min of reaction time. Electrical measurements using a standard probestation indicated that the junction between individual thiophene-functionalized Si MW’s and the conducing polymer poly(3,4 – ethylenedioxythiophene)/poly(styrenesulfonate) (PEDOT:PSS) became more ohmic as more thiophene was added to the MW surface. Under a light-limited current of 20 nA, representative of operation of Si MWs under 1 Sun illumination conditions, the iR loss of thiophene-n-Si MW/PEDOT-PSS contacts was 20 mV, representing an order of magnitude reduction compared with PEDOT-PSS junctions formed with methyl terminated n–Si MWs. Such iR losses are much less than typical catalytic overpotentials for fuel formation, and hence the thiophene-functionalized Si MW contacts will not limit the performance of a Si MW array-based ...
- 3 December 2015
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 7 (49) , 27160-27166
Electrical Characteristics of the Junction between PEDOT:PSS and Thiophene-Functionalized Silicon Microwires
Thiophene moieties have been attached to Si microwires (Si MWs) by a two–step chlorination/alkylation reaction method. X-ray photoelectron spectroscopy indicated that saturation of the surface occurred after 30 min of reaction time. Electrical measurements using a standard probestation indicated that the junction between individual thiophene-functionalized Si MW’s and the conducing polymer poly(3,4 – ethylenedioxythiophene)/poly(styrenesulfonate) (PEDOT:PSS) became more ohmic as more thiophene was added to the MW surface. Under a light-limited current of 20 nA, representative of operation of Si MWs under 1 Sun illumination conditions, the iR loss of thiophene-n-Si MW/PEDOT-PSS contacts was 20 mV, representing an order of magnitude reduction compared with PEDOT-PSS junctions formed with methyl terminated n–Si MWs. Such iR losses are much less than typical catalytic overpotentials for fuel formation, and hence the thiophene-functionalized Si MW contacts will not limit the performance of a Si MW array-based ...
- 1 August 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 610-613
Statistical texture analysis of morphological changes in pressboard insulation due to thermal aging and partial discharges
Power transformer pressboard insulation is subject to thermal aging effects during normal operation that can result in micrometer-scale physical/morphological changes to its surface. Such surface irregularities can increase the likelihood of particle/contaminant attachment to pressboard surfaces or static electrification of oil flowing along these surfaces. Both phenomena can lead to partial discharges which can ultimately lead to insulation failure. In this work, pressboard samples were thermally stressed in air inside an oven to produce pressboards with differing levels of thermal aging and therefore varying surface irregularities. Another set of samples were immersed in insulating oil after thermal stressing, and stressed electrically to produce surface tracking partial discharges. A statistical texture analysis of the thermally and electrically stressed samples was used to demonstrate that the surface condition of pressboard samples were affected by thermal deterioration and the presence of partial discharges.
- 1 August 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 610-613
Statistical texture analysis of morphological changes in pressboard insulation due to thermal aging and partial discharges
Power transformer pressboard insulation is subject to thermal aging effects during normal operation that can result in micrometer-scale physical/morphological changes to its surface. Such surface irregularities can increase the likelihood of particle/contaminant attachment to pressboard surfaces or static electrification of oil flowing along these surfaces. Both phenomena can lead to partial discharges which can ultimately lead to insulation failure. In this work, pressboard samples were thermally stressed in air inside an oven to produce pressboards with differing levels of thermal aging and therefore varying surface irregularities. Another set of samples were immersed in insulating oil after thermal stressing, and stressed electrically to produce surface tracking partial discharges. A statistical texture analysis of the thermally and electrically stressed samples was used to demonstrate that the surface condition of pressboard samples were affected by thermal deterioration and the presence of partial discharges.
- Open Access
- 17 June 2015
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 619
Fabrication of an interdigitated sample holder for dielectric spectroscopy of thin films
- 17 June 2015
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 619
Open AccessFabrication of an interdigitated sample holder for dielectric spectroscopy of thin films
- 12 January 2015
- Published by AIP Publishing in Applied Physics Letters
- Vol. 106 (2) , 022107
Piezoresistive characterization of bottom-up, n-type silicon microwires undergoing bend deformation
The piezoresistance of silicon has been studied over the past few decades in order to characterize the material's unique electromechanical properties and investigate their wider applicability. While bulk and top-down (etched) micro- and nano-wires have been studied extensively, less work exists regarding bottom-up grown microwires. A facile method is presented for characterizing the piezoresistance of released, phosphorus-doped silicon microwires that have been grown, bottom-up, via a chemical vapour deposition, vapour-liquid-solid process. The method uses conductive tungsten probes to simultaneously make electrical measurements via direct ohmic contact and apply mechanical strain via bend deformation. These microwires display piezoresistive coefficients within an order of magnitude of those expected for bulk n-type silicon; however, they show an anomalous response at degenerate doping concentrations (∼1020 cm−3) when compared to lower doping concentrations (∼1017 cm−3), with a stronger piezoresistive coefficient exhibited for the more highly doped wires. This response is postulated to be due to the different growth mechanism of bottom-up microwires as compared to top-down.
- 12 January 2015
- Published by AIP Publishing in Applied Physics Letters
- Vol. 106 (2) , 022107
Piezoresistive characterization of bottom-up, n-type silicon microwires undergoing bend deformation
The piezoresistance of silicon has been studied over the past few decades in order to characterize the material's unique electromechanical properties and investigate their wider applicability. While bulk and top-down (etched) micro- and nano-wires have been studied extensively, less work exists regarding bottom-up grown microwires. A facile method is presented for characterizing the piezoresistance of released, phosphorus-doped silicon microwires that have been grown, bottom-up, via a chemical vapour deposition, vapour-liquid-solid process. The method uses conductive tungsten probes to simultaneously make electrical measurements via direct ohmic contact and apply mechanical strain via bend deformation. These microwires display piezoresistive coefficients within an order of magnitude of those expected for bulk n-type silicon; however, they show an anomalous response at degenerate doping concentrations (∼1020 cm−3) when compared to lower doping concentrations (∼1017 cm−3), with a stronger piezoresistive coefficient exhibited for the more highly doped wires. This response is postulated to be due to the different growth mechanism of bottom-up microwires as compared to top-down.