Ameen El-Sinawi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ameen El-Sinawi has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Karumuri Srinivasa Rao
VLSI-Microelectronics Research Lab, Department of Electronics and Communication Engineering, Koneru Lakshmaiah Education Foundation (Deemed to be University), Vaddeswaram, India
2 shared publications - Koushik Guha
Department of Electronics and Communication Engineering, National Institute of Technology, Silchar, India
2 shared publications - Bukya Balaji
Koneru Lakshmaiah Education Foundation
1 shared publication - Isam Janajreh
Mechanical and Nuclear Engineering Department, Khalifa University of Science and Technology, Abu Dhabi, United Arab Emirates
1 shared publication Jabir Ubaid Parakkal
Mechanical Engineering Dept., Khalifa University of Science and Technology, Masdar Institute, P.O. Box 54224, Abu Dhabi, UAE
1 shared publicationJamal Shaikh‐Ahmad
Mechanical Engineering Department Khalifa University Abu Dhabi United Arab Emirates
1 shared publication
Latest Publications
- 16 October 2022
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 9 (4) , 1701-1722
Method for predicting tool condition using kriging analysis of normalised frequency shifts of spindle acceleration signature and validation in trimming operations of CFRPs
This work presents a method that deals with the problem of determining tool wear, surface roughness, and cutter temperate in the machining of a carbon fibre-reinforced polymer (CFRP) workpiece without the need for removing the tool for inspection. The spindle acceleration signature is dominated by the cutter passing frequency and its first harmonic. Cutting parameters and tool conditions strongly correlate with shifts in the latter two frequencies. The kriging method is utilised to construct prediction models of tool conditions using cutting parameters and spectral shifts. The presented Kriging-based method is unique in its ability to generate acceptable predictions of tool conditions using a small set of experimental data to construct the prediction models. Validation experiments have shown that the proposed method predicted tool wear, surface roughness, and cutter temperature with accuracies of 91%, 86%, and 84%, respectively. Benchmarking of the proposed method against another prediction method has shown acceptable performance.
- 16 October 2022
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 9 (4) , 1701-1722
Method for predicting tool condition using kriging analysis of normalised frequency shifts of spindle acceleration signature and validation in trimming operations of CFRPs
This work presents a method that deals with the problem of determining tool wear, surface roughness, and cutter temperate in the machining of a carbon fibre-reinforced polymer (CFRP) workpiece without the need for removing the tool for inspection. The spindle acceleration signature is dominated by the cutter passing frequency and its first harmonic. Cutting parameters and tool conditions strongly correlate with shifts in the latter two frequencies. The kriging method is utilised to construct prediction models of tool conditions using cutting parameters and spectral shifts. The presented Kriging-based method is unique in its ability to generate acceptable predictions of tool conditions using a small set of experimental data to construct the prediction models. Validation experiments have shown that the proposed method predicted tool wear, surface roughness, and cutter temperature with accuracies of 91%, 86%, and 84%, respectively. Benchmarking of the proposed method against another prediction method has shown acceptable performance.
- 1 June 2021
- Published by Elsevier in Microelectronics Journal
- Vol. 112, 105050
An intensive approach to optimize capacitive type RF MEMS shunt switch
- 1 June 2021
- Published by Elsevier in Microelectronics Journal
- Vol. 112, 105050
An intensive approach to optimize capacitive type RF MEMS shunt switch
- 15 February 2019
- Published by Wiley in International Journal of Numerical Modelling: Electronic Networks, Devices and Fields
- Vol. 32 (3)
A study of the effect of transient stresses on the fatigue life of RF MEMS switches
Fatigue affects the durability of radio frequency microelectromechanical systems (RF MEMS) devices. It is common to rely on actuation voltage cycles or resonant frequencies shift to estimate the fatigue life of MEMS devices. Actuation of moving mechanical parts within the device causes transient stresses because of transient vibration. Such stresses and stress cycles are difficult to account for when fatigue life is estimated by observing actuation voltage or resonant frequencies shift only. This work investigates the effect of transient stresses on the durability of RF MEMS switch, using a benchmarked finite element‐based structural dynamics model of the switch to generate the stress‐time history of the device. Principal normal stresses are calculated from raw stress data and ordered such that (σ1 ≥ σ2 ≥ σ3). Maximum principal stress amplitudes at pull‐in and pull‐out are calculated, and their corresponding number of cycles are determined by rainflow counting method. A Cumulative damage index (Dc) is determined using Miner's rule. This study revealed that, when transient stresses are taken into consideration, the cumulative damage caused by a single on‐off cycle, of the switch studied, is 1.031 × 10−6, and its life‐to‐failure is 9.7 × 105 on‐off cycles. Whereas the life‐to‐failure of the switch, without considering transient stresses, is approximately 10.3 × 108 cycles. Results are compared with published data for similar switches, and they are in good agreement.
- 15 February 2019
- Published by Wiley in International Journal of Numerical Modelling: Electronic Networks, Devices and Fields
- Vol. 32 (3)
A study of the effect of transient stresses on the fatigue life of RF MEMS switches
Fatigue affects the durability of radio frequency microelectromechanical systems (RF MEMS) devices. It is common to rely on actuation voltage cycles or resonant frequencies shift to estimate the fatigue life of MEMS devices. Actuation of moving mechanical parts within the device causes transient stresses because of transient vibration. Such stresses and stress cycles are difficult to account for when fatigue life is estimated by observing actuation voltage or resonant frequencies shift only. This work investigates the effect of transient stresses on the durability of RF MEMS switch, using a benchmarked finite element‐based structural dynamics model of the switch to generate the stress‐time history of the device. Principal normal stresses are calculated from raw stress data and ordered such that (σ1 ≥ σ2 ≥ σ3). Maximum principal stress amplitudes at pull‐in and pull‐out are calculated, and their corresponding number of cycles are determined by rainflow counting method. A Cumulative damage index (Dc) is determined using Miner's rule. This study revealed that, when transient stresses are taken into consideration, the cumulative damage caused by a single on‐off cycle, of the switch studied, is 1.031 × 10−6, and its life‐to‐failure is 9.7 × 105 on‐off cycles. Whereas the life‐to‐failure of the switch, without considering transient stresses, is approximately 10.3 × 108 cycles. Results are compared with published data for similar switches, and they are in good agreement.
- Open Access
- 1 February 2019
- Published by Elsevier in Energy Procedia
- Vol. 158, 1194-1201
Numerical analysis of VAWT wind turbines: Joukowski vs classical NACA rotor’s blades
- 1 February 2019
- Published by Elsevier in Energy Procedia
- Vol. 158, 1194-1201
Open AccessNumerical analysis of VAWT wind turbines: Joukowski vs classical NACA rotor’s blades
- 1 January 2015
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 221, 123-130
A novel comprehensive approach to feedback control of membrane displacement in radio frequency micro-electromechanical switches
- 1 January 2015
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 221, 123-130
A novel comprehensive approach to feedback control of membrane displacement in radio frequency micro-electromechanical switches