Kannan Pidugu Kesavan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kannan Pidugu Kesavan has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Evgeny Alekseevich Trofimov
Department of Materials Science, Physical and Chemical Properties of Materials, South Ural State University, Chelyabinsk 454080, Russia
5 shared publications - Mariappan Anandkumar
South Ural State University, Chelyabinsk, Russia
5 shared publications - Shanmugavel Sudarsan
Department of Chemistry, Saveetha Engineering College, Chennai, India
4 shared publications - Suhash Ranjan Dey
Department of Materials Science and Metallurgical Engineering, Indian Institute of Technology Hyderabad, Kandi, Sangareddy, India
4 shared publications Sushmita Chaudhari
4 shared publications- Ahmad Ostovari Moghaddam
HSE University, Moscow, Russia
2 shared publications
Latest Publications
- Open Access
Sunlight-Assisted Photocatalytic Degradation of Rhodamine B Dye by High-Entropy Fluorite Oxide
In the present work, a six-cation high-entropy fluorite-type oxide photocatalyst composition (Ce1/6Gd1/6Pr1/6Sm1/6Y1/6Zr1/6)O2−δ (HEFO) was prepared with the concept of “high entropy” using a glycine-assisted solution combustion method. Several characterization techniques, such as X-ray diffraction (XRD), UV–visible spectroscopy, and field emission scanning electron microscopy (FESEM), were employed to evaluate the physicochemical properties. Structural analysis by XRD confirmed the formation of a single-phase cubic fluorite structure supported by the Rietveld refinement analysis. The photocatalytic application was systematically evaluated using the prepared HEFO for the degradation of Rhodamine B dye with the help of natural sunlight and H2O2. Several parameters such as photocatalyst dose, dye concentration, and pH were investigated, and the results revealed that 25 mg of photocatalyst, 20 ppm dye concentration, and pH 11 achieved 99.25% of Rhodamine B degradation. Similarly, radical-scavenger tests suggested the involvement of more than one reactive pathway. In addition, the photocatalyst demonstrated excellent reusability, retaining 74.46% degradation efficiency after five cycles (83.6% activity retention), with XRD confirming the preserved cubic fluorite structure. The photocatalytic investigations demonstrate high-entropy oxides to be highly efficient and sustainable photocatalysts for the degradation of Rhodamine B dye.
Open AccessSunlight-Assisted Photocatalytic Degradation of Rhodamine B Dye by High-Entropy Fluorite Oxide
In the present work, a six-cation high-entropy fluorite-type oxide photocatalyst composition (Ce1/6Gd1/6Pr1/6Sm1/6Y1/6Zr1/6)O2−δ (HEFO) was prepared with the concept of “high entropy” using a glycine-assisted solution combustion method. Several characterization techniques, such as X-ray diffraction (XRD), UV–visible spectroscopy, and field emission scanning electron microscopy (FESEM), were employed to evaluate the physicochemical properties. Structural analysis by XRD confirmed the formation of a single-phase cubic fluorite structure supported by the Rietveld refinement analysis. The photocatalytic application was systematically evaluated using the prepared HEFO for the degradation of Rhodamine B dye with the help of natural sunlight and H2O2. Several parameters such as photocatalyst dose, dye concentration, and pH were investigated, and the results revealed that 25 mg of photocatalyst, 20 ppm dye concentration, and pH 11 achieved 99.25% of Rhodamine B degradation. Similarly, radical-scavenger tests suggested the involvement of more than one reactive pathway. In addition, the photocatalyst demonstrated excellent reusability, retaining 74.46% degradation efficiency after five cycles (83.6% activity retention), with XRD confirming the preserved cubic fluorite structure. The photocatalytic investigations demonstrate high-entropy oxides to be highly efficient and sustainable photocatalysts for the degradation of Rhodamine B dye.
- Open Access
- 17 June 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (12) , 939
Phase Evolution of High-Entropy Stannate Pyrochlore Oxide Synthesized via Glycine-Assisted Sol–Gel Synthesis as a Thermal Barrier Coating Material
High-entropy ceramics have gained wider attention due to their structural integrity and stability, which can be used in various functional applications. Especially, high-entropy oxides exhibit excellent thermal stability, particularly at high temperatures. Thermal barrier coating materials must demonstrate good thermal stability without any phase transformation or phase separation, which is critical in aerospace and energy conversion applications. To address this, we have prepared new high-entropy stannate pyrochlore oxide nanoparticles with the composition (Gd0.2Nd0.2La0.2Pr0.2Sm0.2)2Sn2O7 through a simple glycine-assisted sol–gel synthesis. The phase evolution was probed at different heat-treatment temperatures from 1000 °C to 1500 °C. Among the temperatures investigated, a single-phase pyrochlore oxide was formed from 1300 °C without any impurity or phase separation. The obtained nanoparticles were characterized using various techniques, including X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), nanoindentation, and dilatometry to investigate their physiochemical and mechanical properties. The Vickers hardness of high-entropy oxides is 4.2 ± 0.33 GPa, while a thermal expansion coefficient (TEC) of 8.7 × 10−6 K−1 at 900 °C is calculated. The results show that the prepared high-entropy pyrochlore oxide can be a suitable candidate for thermal barrier coating.
- 17 June 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (12) , 939
Open AccessPhase Evolution of High-Entropy Stannate Pyrochlore Oxide Synthesized via Glycine-Assisted Sol–Gel Synthesis as a Thermal Barrier Coating Material
High-entropy ceramics have gained wider attention due to their structural integrity and stability, which can be used in various functional applications. Especially, high-entropy oxides exhibit excellent thermal stability, particularly at high temperatures. Thermal barrier coating materials must demonstrate good thermal stability without any phase transformation or phase separation, which is critical in aerospace and energy conversion applications. To address this, we have prepared new high-entropy stannate pyrochlore oxide nanoparticles with the composition (Gd0.2Nd0.2La0.2Pr0.2Sm0.2)2Sn2O7 through a simple glycine-assisted sol–gel synthesis. The phase evolution was probed at different heat-treatment temperatures from 1000 °C to 1500 °C. Among the temperatures investigated, a single-phase pyrochlore oxide was formed from 1300 °C without any impurity or phase separation. The obtained nanoparticles were characterized using various techniques, including X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), nanoindentation, and dilatometry to investigate their physiochemical and mechanical properties. The Vickers hardness of high-entropy oxides is 4.2 ± 0.33 GPa, while a thermal expansion coefficient (TEC) of 8.7 × 10−6 K−1 at 900 °C is calculated. The results show that the prepared high-entropy pyrochlore oxide can be a suitable candidate for thermal barrier coating.
- Open Access
- 22 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Latin America Transactions
- Vol. 23 (5) , 380-386
Enhancing Cu2ZnSnS4 Solar Cell Efficiency through Antimony Substitution for Tin: A SCAPS-1D Simulation Study
SCAPS-1D, a one-dimensional solar cell simulator, provides a valuable tool for predicting device performance based on layer-by-layer material properties. Copper Zinc Tin Sulfide (CZTS) has emerged as a promising absorber material due to its exceptional light absorption coefficient and the abundance and non-toxic nature of its constituent elements. This study leverages SCAPS-1D to investigate the working mechanism of CZTS-based solar cells. We simulate a Mo/CZTS/CdS/ZnO device structure under AM 1.5 spectrum illumination and 300 K temperature, analyzing the impact of individual layer thickness on photovoltaic performance. Further, a comparative analysis explores the influence of various n-type materials.. In addition, the introduction of antimony (Sb) doping into CZTS leads to a significant change in efficiency of the cell. The efficiency of Sbdoping CZTS attained 21.90%, while there was a great improvement by 3% via reduced recombination losses and enhanced photocurrent. This work gives an insight into the possibility of Sb doping for the improvement in the performance of thin-film solar cells.
- 22 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Latin America Transactions
- Vol. 23 (5) , 380-386
Open AccessEnhancing Cu2ZnSnS4 Solar Cell Efficiency through Antimony Substitution for Tin: A SCAPS-1D Simulation Study
SCAPS-1D, a one-dimensional solar cell simulator, provides a valuable tool for predicting device performance based on layer-by-layer material properties. Copper Zinc Tin Sulfide (CZTS) has emerged as a promising absorber material due to its exceptional light absorption coefficient and the abundance and non-toxic nature of its constituent elements. This study leverages SCAPS-1D to investigate the working mechanism of CZTS-based solar cells. We simulate a Mo/CZTS/CdS/ZnO device structure under AM 1.5 spectrum illumination and 300 K temperature, analyzing the impact of individual layer thickness on photovoltaic performance. Further, a comparative analysis explores the influence of various n-type materials.. In addition, the introduction of antimony (Sb) doping into CZTS leads to a significant change in efficiency of the cell. The efficiency of Sbdoping CZTS attained 21.90%, while there was a great improvement by 3% via reduced recombination losses and enhanced photocurrent. This work gives an insight into the possibility of Sb doping for the improvement in the performance of thin-film solar cells.
- Open Access
Band-Gap Engineering of High-Entropy Fluorite Metal Oxide Nanoparticles Facilitated by Pr3+ Incorporation by Gel Combustion Synthesis
Tailoring the bandgap of a material is necessary for improving its optical properties. Here, the optical bandgap of high-entropy oxide Ce0.2Gd0.2Sm0.2Y0.2Zr0.2O2-δ (HEO) nanoparticles was modified using Pr3+. Various concentrations of Pr3+ (x = 0, 0.01, 0.02, 0.05, 0.075, 0.1, 0.15) were incorporated into the host high-entropy oxide using a gel combustion synthesis. After the gel combustion step, the powders were heat-treated at various temperatures (650 °C, 800 °C, 950 °C) for 2 h. The obtained Pr3+-incorporated HEO powders were characterized using X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and UV–visible spectroscopy. The results indicate that, when the samples are calcined at 950 °C, a single-phase cubic fluorite structure is obtained without any phase separation or impurity. The optical absorbance red-shifts to higher wavelengths when the concentration of Pr3+ is increased. This reduces the bandgap of the material from 3.15 eV to 1.87 eV for Pr3+ concentrations of x = 0 (HEO-0) and x = 0.15 (HEO-6), respectively. The obtained HEOs can be suitable candidates for photocatalytic applications due to their absorbance in the visible region.
Open AccessBand-Gap Engineering of High-Entropy Fluorite Metal Oxide Nanoparticles Facilitated by Pr3+ Incorporation by Gel Combustion Synthesis
Tailoring the bandgap of a material is necessary for improving its optical properties. Here, the optical bandgap of high-entropy oxide Ce0.2Gd0.2Sm0.2Y0.2Zr0.2O2-δ (HEO) nanoparticles was modified using Pr3+. Various concentrations of Pr3+ (x = 0, 0.01, 0.02, 0.05, 0.075, 0.1, 0.15) were incorporated into the host high-entropy oxide using a gel combustion synthesis. After the gel combustion step, the powders were heat-treated at various temperatures (650 °C, 800 °C, 950 °C) for 2 h. The obtained Pr3+-incorporated HEO powders were characterized using X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and UV–visible spectroscopy. The results indicate that, when the samples are calcined at 950 °C, a single-phase cubic fluorite structure is obtained without any phase separation or impurity. The optical absorbance red-shifts to higher wavelengths when the concentration of Pr3+ is increased. This reduces the bandgap of the material from 3.15 eV to 1.87 eV for Pr3+ concentrations of x = 0 (HEO-0) and x = 0.15 (HEO-6), respectively. The obtained HEOs can be suitable candidates for photocatalytic applications due to their absorbance in the visible region.
- 17 November 2024
- Published by Elsevier in Ceramics International
- Vol. 51 (3) , 2770-2778
Electrochemical detection of p-nitrophenol using glassy carbon electrode modified using high-entropy oxide nanoparticles
- 17 November 2024
- Published by Elsevier in Ceramics International
- Vol. 51 (3) , 2770-2778
Electrochemical detection of p-nitrophenol using glassy carbon electrode modified using high-entropy oxide nanoparticles
- 17 July 2024
- Published by Elsevier in Surfaces and Interfaces
- Vol. 51
High-entropy oxide (CeGdHfPrZr)O2 nanoparticles as reusable photocatalyst for wastewater remediation
- 17 July 2024
- Published by Elsevier in Surfaces and Interfaces
- Vol. 51
High-entropy oxide (CeGdHfPrZr)O2 nanoparticles as reusable photocatalyst for wastewater remediation
- 1 March 2018
- Published by Elsevier in Thin Solid Films
- Vol. 649, 81-88
Detailed investigations on influence of precursor stacking and sulfurization for Cu2ZnSnS4 film formation
- 1 March 2018
- Published by Elsevier in Thin Solid Films
- Vol. 649, 81-88
Detailed investigations on influence of precursor stacking and sulfurization for Cu2ZnSnS4 film formation
- 1 August 2017
- Published by Elsevier in Thin Solid Films
- Vol. 636, 144-149
Influence of stabilizing agent on dip coating of Cu2ZnSnS4 thin film
- 1 August 2017
- Published by Elsevier in Thin Solid Films
- Vol. 636, 144-149
Influence of stabilizing agent on dip coating of Cu2ZnSnS4 thin film
- 1 August 2016
- Published by Elsevier in Thin Solid Films
- Vol. 612, 456-462
Investigation of optimum annealing parameters for formation of dip coated Cu2ZnSnS4 thin film
- 1 August 2016
- Published by Elsevier in Thin Solid Films
- Vol. 612, 456-462
Investigation of optimum annealing parameters for formation of dip coated Cu2ZnSnS4 thin film
- 1 February 2016
- Published by Elsevier in Thin Solid Films
- Vol. 600, 169-174
Pulsed electrodeposition of Cu2ZnSnS4 absorber layer precursor for photovoltaic application
- 1 February 2016
- Published by Elsevier in Thin Solid Films
- Vol. 600, 169-174
Pulsed electrodeposition of Cu2ZnSnS4 absorber layer precursor for photovoltaic application