Jamie Alberto Escobar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jamie Alberto Escobar has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Omar Darío Lopez Mejia
Department of Mechanical Engineering, Universidad de los Andes, Cra 1 Este N 19A-40, Bogota 111711, Colombia
4 shared publications Carlos Silva
3 shared publications- Andres Mauricio Pérez Gordillo
University of Los Andes
2 shared publications Camilo A. Suarez
2 shared publicationsCarlos A. Lara
2 shared publications- Juan Sebastian Velandia
Institute of Fluid Mechanics, TU Braunschweig
2 shared publications
Latest Publications
- Open Access
Influence of the Reynolds Number on the Aerodynamic Performance of a Small Rotor
The use of small rotors has increased due their applications in drones and UAVs. In order to improve the global performance of these aerial vehicles, it is necessary to understand the aerodynamics of small rotors, since this is related to the global energy consumption of such vehicles. Most of the computational fluid dynamics (CFD) studies found in the literature that are related to the analysis of small rotors employ fully turbulent models, despite the low-to-moderate Reynolds numbers of these applications. This paper presents CFD simulations for a small rotor at hover at different Reynolds numbers using fully turbulent and transitional SST turbulence models. Numerical results show that thrust and torque are close to experimental measurements, showing differences of less than 5% for both fully turbulent and transitional models. However, significant differences were observed between the fully turbulent and the transitional models when studying the boundary-layer development and separation. As the Reynolds number was increased, it was observed that at the tip of the blade, these differences were reduced, but at mid-span, the differences were more obvious.Open AccessInfluence of the Reynolds Number on the Aerodynamic Performance of a Small Rotor
The use of small rotors has increased due their applications in drones and UAVs. In order to improve the global performance of these aerial vehicles, it is necessary to understand the aerodynamics of small rotors, since this is related to the global energy consumption of such vehicles. Most of the computational fluid dynamics (CFD) studies found in the literature that are related to the analysis of small rotors employ fully turbulent models, despite the low-to-moderate Reynolds numbers of these applications. This paper presents CFD simulations for a small rotor at hover at different Reynolds numbers using fully turbulent and transitional SST turbulence models. Numerical results show that thrust and torque are close to experimental measurements, showing differences of less than 5% for both fully turbulent and transitional models. However, significant differences were observed between the fully turbulent and the transitional models when studying the boundary-layer development and separation. As the Reynolds number was increased, it was observed that at the tip of the blade, these differences were reduced, but at mid-span, the differences were more obvious. - Open Access
- 15 December 2022
- Published by MDPI AG in Chemosensors
- Vol. 10 (12) , 538
Kullback–Leibler Importance Estimation Procedure to Improve Gas Quantification in an Electronic Nose
An electronic nose sensor array can classify and quantify different types of gases; however, the sensor can alter its measurement capability over time. The main problem presented during the measurements of the sensors is related to the variation of the data acquired for long periods due to changes in the chemosensory response, thus affecting the correct functioning of the implemented measuring system. This research presents an approach to improve gas quantification through the implementation of machine learning regression techniques in an array of nose-type electronic sensors. The implemented methodology uses a domain adaptation approach with the Kullback–Leibler importance estimation procedure (KLIEP) to improve the performance of the gas quantification electronic nose array. This approach is validated using a three-year dataset measured by a 16-electronic-nose-sensor array. The R2 regression error obtained for each of the gases fits the resulting dataset’s measured values with good precision.
- 15 December 2022
- Published by MDPI AG in Chemosensors
- Vol. 10 (12) , 538
Open AccessKullback–Leibler Importance Estimation Procedure to Improve Gas Quantification in an Electronic Nose
An electronic nose sensor array can classify and quantify different types of gases; however, the sensor can alter its measurement capability over time. The main problem presented during the measurements of the sensors is related to the variation of the data acquired for long periods due to changes in the chemosensory response, thus affecting the correct functioning of the implemented measuring system. This research presents an approach to improve gas quantification through the implementation of machine learning regression techniques in an array of nose-type electronic sensors. The implemented methodology uses a domain adaptation approach with the Kullback–Leibler importance estimation procedure (KLIEP) to improve the performance of the gas quantification electronic nose array. This approach is validated using a three-year dataset measured by a 16-electronic-nose-sensor array. The R2 regression error obtained for each of the gases fits the resulting dataset’s measured values with good precision.
- Open Access
Numerical and Experimental Estimation of the Efficiency of a Quadcopter Rotor Operating at Hover
Globalization has led to an increase in the use of small copters for different activities such as geo-referencing, agricultural fields monitoring, survillance, among others. This is the main reason why there is a strong interest in the performance of small-scale propellers used in unmanned aerial vehicles. The flow developed by rotors is complex and the estimation of its aerodynamic performance is not a trivial process. In addition, viscous effects, when the rotor operates at low Reynolds, affect its performance. In the present paper, two different computational methods, Computational Fluid Dynamics (CFD) and the Unsteady Vortex Lattice Method (UVLM) with a viscous correction, were used to study the performance of an isolated rotor of a quadcopter flying at hover. The Multi Reference Frame model and transition turbulence model were used in the CFD simulations. The tip vortex core growth was used to account for the viscous effects in the UVLM. The wake structure, pressure coefficient, thrust and torque predictions from both methods are compared. Thrust and torque results from simulations were validated by means of experimental results of a characterization of a single rotor. Finally, figure of merit of the rotor is evaluated showing that UVLM overestimates the efficiency of the rotor; meanwhile, CFD predictions are close to experimental values.Open AccessNumerical and Experimental Estimation of the Efficiency of a Quadcopter Rotor Operating at Hover
Globalization has led to an increase in the use of small copters for different activities such as geo-referencing, agricultural fields monitoring, survillance, among others. This is the main reason why there is a strong interest in the performance of small-scale propellers used in unmanned aerial vehicles. The flow developed by rotors is complex and the estimation of its aerodynamic performance is not a trivial process. In addition, viscous effects, when the rotor operates at low Reynolds, affect its performance. In the present paper, two different computational methods, Computational Fluid Dynamics (CFD) and the Unsteady Vortex Lattice Method (UVLM) with a viscous correction, were used to study the performance of an isolated rotor of a quadcopter flying at hover. The Multi Reference Frame model and transition turbulence model were used in the CFD simulations. The tip vortex core growth was used to account for the viscous effects in the UVLM. The wake structure, pressure coefficient, thrust and torque predictions from both methods are compared. Thrust and torque results from simulations were validated by means of experimental results of a characterization of a single rotor. Finally, figure of merit of the rotor is evaluated showing that UVLM overestimates the efficiency of the rotor; meanwhile, CFD predictions are close to experimental values. - 11 April 2018
- Published by Springer Nature
- p. 93-111
RANS Simulations of the High Lift Common Research Model with Open-Source Code SU2
- 11 April 2018
- Published by Springer Nature
- p. 93-111
RANS Simulations of the High Lift Common Research Model with Open-Source Code SU2
- 1 July 2015
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Aircraft
- Vol. 52 (4) , 1112-1121
Detached-Eddy Simulation of a Wide-Body Commercial Aircraft in High-Lift Configuration
Numerical prediction of the aerodynamic properties of high-lift configurations has become an important topic for the computational fluid dynamics community in the last years. The present paper shows and discusses a numerical study of the DLR-F11 high-lift configuration that was used as a model reference in the Second High-Lift Prediction Workshop, organized by the AIAA in 2013. Case 1 of the workshop was simulated with the commercial software ANSYS Fluent v14.5, using the Spalart–Allmaras (fully turbulent Reynolds-averaged Navier–Stokes) model. Numerical results showed good agreement for angles of attack lower than 18 deg; however, above this value, simulations were not accurate enough near to . To study the influence of the turbulence model in the dynamics of the flow and the numerical prediction of the aerodynamic properties near to , the original grids were adapted and a hybrid Reynolds-averaged Navier–Stokes/large-eddy simulation model (detached-eddy simulation based on Spalart–Allmaras) was used. Numerical results for the detached-eddy simulation showed a small change in the prediction of the aerodynamic properties near to , as well as improved vorticity resolution in the wake.- 1 July 2015
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Aircraft
- Vol. 52 (4) , 1112-1121
Detached-Eddy Simulation of a Wide-Body Commercial Aircraft in High-Lift Configuration
Numerical prediction of the aerodynamic properties of high-lift configurations has become an important topic for the computational fluid dynamics community in the last years. The present paper shows and discusses a numerical study of the DLR-F11 high-lift configuration that was used as a model reference in the Second High-Lift Prediction Workshop, organized by the AIAA in 2013. Case 1 of the workshop was simulated with the commercial software ANSYS Fluent v14.5, using the Spalart–Allmaras (fully turbulent Reynolds-averaged Navier–Stokes) model. Numerical results showed good agreement for angles of attack lower than 18 deg; however, above this value, simulations were not accurate enough near to . To study the influence of the turbulence model in the dynamics of the flow and the numerical prediction of the aerodynamic properties near to , the original grids were adapted and a hybrid Reynolds-averaged Navier–Stokes/large-eddy simulation model (detached-eddy simulation based on Spalart–Allmaras) was used. Numerical results for the detached-eddy simulation showed a small change in the prediction of the aerodynamic properties near to , as well as improved vorticity resolution in the wake.