Shigeru Hamada
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Shigeru Hamada has a total of 147 co-authors. Here are the top co-authors by number of shared publications:
- Hiroshi Noguchi
Kyushu University
46 shared publications Hiroshi Noguchi
15 shared publications- Motomichi Koyama
Institute for Materials Research, Tohoku University
13 shared publications Saburo Matsuoka
Kyushu University, Fukuoka, Japan
6 shared publicationsHao Wu
Department of Mechanical Engineering, Graduate School of Engineering, Kyushu University, 744 Moto-oka, Nishi-Ku, Fukuoka 819-0395, Japan
5 shared publicationsHisao Matsunaga
Research Center for Hydrogen Industrial Use and Storage, Kyushu University
5 shared publications
Latest Publications
- Open Access
- 14 October 2026
- Published by Elsevier in Materials & Design
- Vol. 271
Materials design framework for mitigating thermal cracking in high-carbon martensitic steel via coordinated cryogenic treatment and tempering
- 14 October 2026
- Published by Elsevier in Materials & Design
- Vol. 271
Open AccessMaterials design framework for mitigating thermal cracking in high-carbon martensitic steel via coordinated cryogenic treatment and tempering
- Open Access
- 3 June 2026
- Published by Elsevier in SSRN Electronic Journal
Hydrogen-Related Fracture in Ultrahigh-Strength Martensitic Steel: Role of Stress Concentration in Notched and Precracked Specimens
Hydrogen-related fracture behavior in ultra-high-strength martensitic steels is strongly influenced by the stress concentration associated with defect geometry. However, a systematic comparison between notch-root-controlled and crack-tip-controlled stress states, particularly using precracked specimens that better represent crack-like defects in service, remains limited. This study systematically compared notched and precracked specimens of a 2 GPa-class martensitic steel to clarify how defect geometry controls hydrogen-related fracture behavior through notch-root stress concentration and crack-tip stress intensity. Slow-strain-rate tensile tests, combined with scanning electron microscopy and electron backscatter diffraction analyses, were performed to correlate fracture morphology with local plastic strain accumulation under hydrogen-charged conditions. Hydrogen exposure significantly reduced the tensile strength of both specimen geometries. In the notched specimens, the strength decreased from 2276 to 1854 MPa, whereas in the precracked specimens, it decreased more severely from 1489 to 577 MPa, indicating a higher susceptibility of crack-tip-controlled configurations to hydrogen embrittlement. Distinct fracture features were observed depending on the type of stress concentration. The notched specimens exhibited mixed fracture features involving intergranular (IG) fracture and shear-band-associated ductile fracture. In contrast, the precracked specimens showed dominant IG fracture at the crack tip, followed by localized transgranular interlath features and increasing ductile dimpling with crack extension, consistent with elevated crack-tip plastic strain revealed by kernel average misorientation analysis. These findings demonstrate that hydrogen-related fracture behavior in ultra-high-strength martensitic steel is strongly controlled by defect-geometry-dependent local stress and strain fields, with important implications for structural integrity assessment in hydrogen environments.
- 3 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessHydrogen-Related Fracture in Ultrahigh-Strength Martensitic Steel: Role of Stress Concentration in Notched and Precracked Specimens
Hydrogen-related fracture behavior in ultra-high-strength martensitic steels is strongly influenced by the stress concentration associated with defect geometry. However, a systematic comparison between notch-root-controlled and crack-tip-controlled stress states, particularly using precracked specimens that better represent crack-like defects in service, remains limited. This study systematically compared notched and precracked specimens of a 2 GPa-class martensitic steel to clarify how defect geometry controls hydrogen-related fracture behavior through notch-root stress concentration and crack-tip stress intensity. Slow-strain-rate tensile tests, combined with scanning electron microscopy and electron backscatter diffraction analyses, were performed to correlate fracture morphology with local plastic strain accumulation under hydrogen-charged conditions. Hydrogen exposure significantly reduced the tensile strength of both specimen geometries. In the notched specimens, the strength decreased from 2276 to 1854 MPa, whereas in the precracked specimens, it decreased more severely from 1489 to 577 MPa, indicating a higher susceptibility of crack-tip-controlled configurations to hydrogen embrittlement. Distinct fracture features were observed depending on the type of stress concentration. The notched specimens exhibited mixed fracture features involving intergranular (IG) fracture and shear-band-associated ductile fracture. In contrast, the precracked specimens showed dominant IG fracture at the crack tip, followed by localized transgranular interlath features and increasing ductile dimpling with crack extension, consistent with elevated crack-tip plastic strain revealed by kernel average misorientation analysis. These findings demonstrate that hydrogen-related fracture behavior in ultra-high-strength martensitic steel is strongly controlled by defect-geometry-dependent local stress and strain fields, with important implications for structural integrity assessment in hydrogen environments.
- Open Access
- 30 March 2026
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 66 (4) , 570-576
Effect of Microstructural Heterogeneity on Fatigue Limit of As-quenched Low-carbon Low-alloy Martensitic Steel
Fatigue crack initiation and subsequent crack propagation behaviour in as-quenched low-carbon low-alloy steel were examined using a rotating-bending fatigue test and electron backscatter diffraction analysis to clarify the relationship between the fatigue limit and the microstructural heterogeneity of martensite. The as-quenched low-carbon low-alloy steel exhibited a low fatigue limit relative to its ultimate tensile strengths. The fatigue fracture was originated from slip deformation due to dislocation glide in the matrix. Furthermore, a tensile test revealed a low elastic limit in the steel, which can be explained by the movement of high-density mobile dislocations introduced during the transformation. These findings suggest that the low fatigue limit of as-quenched low-carbon low-alloy steel is due to its low elastic limit. Fatigue cracks initiated at prior austenite grain boundaries (PAGBs), at packet boundaries, and parallel to the block boundaries. These crack initiations were triggered by the preferential activation of slip systems parallel to the habit plane in the coarse martensite, which was nucleated at the PAGBs in the early stage of transformation and satisfied the Kurdjumov–Sachs orientation relationship (K–S OR), with not only its own parent austenite grain but also the adjacent austenite grain (i.e. the double K–S OR). Additionally, the initiated cracks were arrested at the fatigue limit. This is probably due to plasticity-induced crack closure stemming from the significant plastic deformation of the early transformed coarse martensite.
- 30 March 2026
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 66 (4) , 570-576
Open AccessEffect of Microstructural Heterogeneity on Fatigue Limit of As-quenched Low-carbon Low-alloy Martensitic Steel
Fatigue crack initiation and subsequent crack propagation behaviour in as-quenched low-carbon low-alloy steel were examined using a rotating-bending fatigue test and electron backscatter diffraction analysis to clarify the relationship between the fatigue limit and the microstructural heterogeneity of martensite. The as-quenched low-carbon low-alloy steel exhibited a low fatigue limit relative to its ultimate tensile strengths. The fatigue fracture was originated from slip deformation due to dislocation glide in the matrix. Furthermore, a tensile test revealed a low elastic limit in the steel, which can be explained by the movement of high-density mobile dislocations introduced during the transformation. These findings suggest that the low fatigue limit of as-quenched low-carbon low-alloy steel is due to its low elastic limit. Fatigue cracks initiated at prior austenite grain boundaries (PAGBs), at packet boundaries, and parallel to the block boundaries. These crack initiations were triggered by the preferential activation of slip systems parallel to the habit plane in the coarse martensite, which was nucleated at the PAGBs in the early stage of transformation and satisfied the Kurdjumov–Sachs orientation relationship (K–S OR), with not only its own parent austenite grain but also the adjacent austenite grain (i.e. the double K–S OR). Additionally, the initiated cracks were arrested at the fatigue limit. This is probably due to plasticity-induced crack closure stemming from the significant plastic deformation of the early transformed coarse martensite.
- Open Access
- 3 February 2026
- Published by Elsevier in Materials & Design
- Vol. 263
Evolution of cold-rolling work roll materials based on the elucidation of the cracking mechanism of thermal shock
- 3 February 2026
- Published by Elsevier in Materials & Design
- Vol. 263
Open AccessEvolution of cold-rolling work roll materials based on the elucidation of the cracking mechanism of thermal shock
- 20 December 2024
- Published by Elsevier in International Journal of Fatigue
- Vol. 193
Fatigue strength evaluation method based on fatigue crack extension mechanism in BCC martensitic steels
- 20 December 2024
- Published by Elsevier in International Journal of Fatigue
- Vol. 193
Fatigue strength evaluation method based on fatigue crack extension mechanism in BCC martensitic steels